2023 CITROEN C3 clock

9
Access
2Key

The key allows the central locking or unlocking of
the vehicle using the door lock.
It also allows the engine to be started or
switched off.
Key with remote control
function
Remote control function

The remote control can be used for the following
remote functions, depending on version:
–
Unlocking / Locking the vehicle.
–


Locating the vehicle.
Key
The key allows starting and switching off the
engine. It can also be used to lock/unlock the
vehicle.
Unlocking the vehicle
With the remote control
► Press this button to unlock the vehicle.
The direction indicators blink twice to signal
unlocking of the vehicle.
With the key
► Turn the key in the driver's door lock
clockwise to unlock.
Locking the vehicle
With the remote control
► Press this button to lock the vehicle.
The direction indicators blink once to signal the
locking of the vehicle.
If one of the doors or the boot is still open, the
central locking does not work; the vehicle locks,
then immediately unlocks, identifiable by the
locks making a rebound sound.
When the vehicle is locked, if it is
unlocked without the opening of a door
or the boot, it will automatically lock itself
again after thirty seconds.
With the key
► Turn the key in the driver's door lock
anticlockwise to lock.
Check that the doors and boot are fully
closed.
Locating the vehicle
This function helps you to spot your vehicle from
a distance, with the vehicle locked.
► Press this button.
The direction indicators or daytime running
lamps/sidelamps, depending on version, flash or
light up for a few seconds.
Advice
Remote control
The remote control is a sensitive, high-
frequency device; avoid handling it in your
pocket, due to the risk of unintentionally
unlocking the vehicle.
Avoid pressing the remote control buttons
while out of range of the vehicle, due to
the risk of rendering the remote control
inoperative. It would then be necessary to
reset it.
The remote control does not work when the
key is in the ignition switch.

10
Access
As a safety precaution, remove the key from the ignition when leaving the
vehicle, even for a short time.
Do not modify the electronic vehicle
immobiliser, as this might result in
malfunctions.
Remember to remove the key and turn the
steering wheel to engage the steering lock.
Central locking
Manual

► Push/pull this knob located on the driver's
door handle to lock/unlock the doors from inside
the vehicle.
When the doors are locked, the red indicator is
no longer visible.
The central locking does not take place if one of the doors is open.
Driving with the doors locked could make
it more difficult for the emergency
services to enter the vehicle in an emergency.
Automatic (anti-intrusion security)
The doors and boot lock automatically when
driving (speed above 4-5
km/h).
Back-up procedures
Lost keys, remote control
Visit a CITROËN dealer with the vehicle's
registration certificate, a personal identification
document and, if possible, the label bearing the
key code.
The CITROËN dealer will be able to retrieve the
key code and the transponder code required to
order a new key.
Central locking not
functioning
Use these procedures in the following cases:
– Central locking malfunction.
–

Battery disconnected or discharged.
In the event of a malfunction of the
central locking system, the battery must
be disconnected to ensure that the vehicle is
locked fully.
Driver's door
► Turn the key anticlockwise to lock it, or
clockwise to unlock it.
All doors
► Use the manual knob in the driver's door to
lock in the four doors and close the doors.
Changing the remote
control battery
Battery ref.: CR2032/3 Volts.

► Hold the key blank and pull the key top cover
in opposite direction.
►

Remove the discharged battery from its
housing.
►


Insert the new battery
, observing the polarity,
and clip the cover onto the housing.
Do not throw remote control batteries
away, as they contain metals that are
harmful to the environment. Take them to an
approved disposal point.

46
In the event of a breakdown
Light-emitting diode (LED)
headlamps and lamps
Depending on version, the affected types of
headlamps / lamps are:
–
Daytime running lamps / sidelamps.
–


Direction indicator side repeaters.
–


Third brake lamp.
–


Number plate lamps.
Light emitting diodes (LED)
For the replacement of this type of bulb,
you must contact a CITROËN dealer.
Do not touch the LED technology lamps - risk
of electrocution!
Front lamps
Model 1

1. Daytime running lamps/sidelamps (W5W
bulb)
2. Direction indicators (PY21W
- 12V - 21W)
3. Beam headlamps (H4
- 12V - 60/55W)
Model 2

1.Daytime running lamps/sidelamps (LED)
2. Direction indicators (PY21W
- 12V - 21W)
3. Beam headlamps (H4
- 12V - 60/55W)
Daytime running lamps/sidelamps

► Turn the bulb holder a quarter of a turn and
pull it out.
►
Pull the bulb out and change it.
Direction indicators
Rapid flashing of a direction indicator
lamp (left or right) indicates that one of
the bulbs on the corresponding side has
failed.


► Turn the bulb holder a eighth of a turn anti-
clockwise and remove it.
►

Remove the bulb and replace it.
Amber coloured bulbs, such as the direction indicators, must be replaced by
bulbs with identical colour and specifications.
Beam headlamps

► Remove the protective cover by pulling on
the tab.
►

Disconnect the bulb connector
.
►

Release the retaining tab.
►


Change the bulb taking care to align the
metal part with the grooves on the lamp.
►


Reposition the retaining tab.
►


Reconnect the bulb connector
.

47
In the event of a breakdown
8► Ensure that the cover is refitted correctly all
around to ensure correct sealing.
Rear lamps
Model 1

1. Sidelamps / Brake lamps
(P21/5W - 12V - 21W/5W)
2. Direction indicators (PY21W
- 12V - 21W)
3. Reversing lamp (P21W
- 12V - 21W)
Model 2

1.Sidelamps / Brake lamps
(P21/5W - 12V - 21W/5W)
2. Direction indicators (PY21W
- 12V - 21W)
3. Reversing lamp (P21W
- 12V - 21W)
4. Additional sidelamps (W3W
- 12V - 3W)
5. Connecting tail lamps (W3W
- 12V - 3W)
Changing bulbs
These bulbs are changed after removing the tail
lamp assembly.
►
Open the boot.
►


Unscrew the nut and remove it. Be careful
not to drop it inside the wing.
►


Unclip the lamp unit and carefully extract it
pulling straight towards the outside.
A

standard pair of pliers or the wheel wrench
(depending on equipment) may be necessary to
remove the nut.
Sidelamps/Brake lamps / Reversing lamp /
Direction indicators


► Turn the bulb holder a eighth of a turn anti-
clockwise and remove it.
►

Remove the bulb and replace it.
Additional sidelamps / Connecting tail
lamps (if equipped)


► Turn the bulb holder a quarter of a turn and
pull it out.
►
Pull the bulb out and change it.
Interior lighting
Courtesy lamp (10W - 12V - 10W)

► Using a thin, flap tip screwdriver , unclip the
entire console surrounding the courtesy lamp.
►

Remove the defective bulb and replace it.
►


Fit the console back into place around the
courtesy lamp and clip it correctly

.

68
10" Touch Screen
Settings

General settings
Press Settings to display the main page.
Press General.
–

Select Language to choose a language in the
list displayed.
–

Select Factory Reset to return to factory
default system.
–

Select About to see information about the
current software version.
–

Select Wi-Fi to generate a new password
for the Wi-Fi network. Only the password can
be changed and not the network name (Wi-Fi
SSID).
The Wi-Fi connection including credential sharing with the user’s smartphone
happens automatically after successful
Bluetooth
® connection with a wireless
supported smartphone.
It cannot be used for Internet sharing in
the vehicle nor software update nor any
other purpose.
The Wi-Fi network uses the 5 GHz frequency. Some smartphones may not
support this feature.
To protect your system, only networks with a sufficient level of security are
allowed to connect. WPA2 encryption level,
equivalent to a domestic level, is required.
Display settings
Press Settings to display the main page.
Press Display.
–

Select User off Mode to enable/disable date
and time display when the system is powered off.
–

Select Brightness to adjust the brightness of
the touch screen by using the + or - buttons.
Phone settings
Press Settings to display the main page.
Press Phone.
–

Select BT visibility to turn on/off the
Bluetooth
® visibility of the system.
–

Select Add device to select a mobile device
to be connected.
–

Select Device list to view the previously
paired mobile devices and connect or delete a
device.
Audio settings
Press Settings to display the main page.
Press Audio .
In this screen, you can modify the Balance
& Fade settings, the Equalizer settings, the
Volume settings and activate the SDVC (Speed
Dependent Volume Control) option.
Clock settings
Press Settings to display the main page.
Press Clock.
Automatic date & time setting
Select Sync to GPS to enable date and time
synchronisation to GPS.
Select Time Zone to choose the appropriate
time zone.
Manual date setting
Select Date.
Choose the date format and then set the day,
month and year using up and down arrows.
Press Set.
Manual time setting
Select Time.
Choose the time format (12 hrs or 24 hrs) and
then set the hours and minutes using up and
down arrows.
Press Set.