2023 CITROEN C3 wheel bolts

42
In the event of a breakdown
Tool kit
Set of tools supplied with the vehicle.
Accessing the tools

The tools are located under the boot floor carpet,
with the spare wheel.
List of tools

1.Jack
To raise the vehicle.
2.Jack handle
3. Wheel wrench
To remove the wheel bolts.
4. Removable towing eye
For more information on Towing the vehicle
and using the removable towing eye, refer to the
corresponding section.
These tools are specific to the vehicle and may vary according to the level of
equipment.
Do not use them for any other purpose.
The jack must only be used to change a wheel with a damaged or punctured tyre.
Do not use any jack other than the one
supplied with the vehicle.
If the vehicle does not have its original jack,
contact a CITROËN dealer.
The jack does not require any maintenance.
Spare wheel
Access to the spare wheel
The spare wheel is installed in the boot, under
the floor carpet.
Removing the spare wheel

► Rotate the fixing screw to unlock the spare
wheel.
►

Lift the spare wheel towards you from the
rear

.
►

T
ake the wheel out of the boot.
Removing the jack

► Rotate the fixing screw to unlock the jack on
one end.
►

T
ilt the jack towards the right and lift it from
the rear.

43
In the event of a breakdown
8Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does
not obstruct traffic: the ground must be level,
stable and non-slippery.
With a manual gearbox, engage first gear to
lock the wheels, apply the parking brake and
switch off the ignition.
Check for the fixed illumination of the parking
brake indicator lamps in the instrument panel.
The occupants must get out of the vehicle
and wait where they are safe.
If necessary, place a chock under the wheel
diagonally opposite the wheel to be changed.
Never go underneath a vehicle raised using a
jack; use an axle stand.
Wheel with wheel trim
When removing the wheel , first remove
the wheel trim by pulling at the valve aperture.
When refitting the wheel , refit the wheel
trim, starting by placing its aperture in line
with the valve and then pushing it into place
all round its edge with the palm of your hand.
Wheel nuts removing pattern

► Loosen the nuts on the wheel in diagonal
sequence. Do not remove wheel nuts.


► Slacken the bolts using the wheel wrench 3
only.


► Place the foot of jack 1 on the ground and
ensure that it is directly below the front A or
rear
B jacking point on the underbody, whichever
is closest to the wheel to be changed.


► Extend jack 1 with the jack handle 2 and
wheel wrench 3 until its head comes into contact
with jacking point

A
or B; contact area A or B
on the vehicle must be properly inserted into the
central part of the head of the jack.
►

Raise the vehicle until there is sufficient
space between the wheel and the ground to
admit the spare (not punctured) wheel easily

.

44
In the event of a breakdown
Ensure that the jack is stable. If the
ground is slippery or loose, the jack may
slip or collapse - risk of injury!
Take care to position the jack strictly at
one of the jacking points

A
or B under the
vehicle, ensuring that the head of the jack is
centred under the contact area of the vehicle.
Otherwise, there is a risk of damage to the
vehicle and/or of the jack collapsing - risk of
injury!


► Remove the bolts and store them in a clean
place.
►

Remove the wheel.
Fitting a wheel

► Fit the wheel on the hub.
► Screw in the bolts by hand as far as possible.
►

Pre-tighten the bolts using the wheel wrench
3

only.


► Lower the vehicle again fully .
► Fold jack 1 and remove it.


► Tighten the bolts using the wheel wrench 3
only.
►

Refit the bolt cover (depending on
equipment).
►


Store the tools.
Putting the spare wheel
back in place


► Put the spare wheel back in its housing.