2022 TOYOTA GR86 wheel size

41
1
1-1. For safe use
For safety and security
For the locations of the SRS
airbags, refer to P.32.
In a moderate to severe frontal col-
lision, the following components
deploy.
 SRS frontal airbag for driver
 SRS frontal airbag for front pas-
senger
 SRS curtain shield airbag*
SRS knee airbag for driver
*: When an offset frontal collision that is
severe enough to deploy the front
airbag occurs.
These components supplement the
seatbelts by reducin g the impact to
the occupant’s head, chest and
knees.
WA R N I N G
• Attachment of any equipment (bush
bar, bullbar, winches, snow plow,
skid/sump plate, etc.) to the front end other than genuine Toyota
accessory parts or parts that match
the quality of genuine Toyota accessory parts.
• Modification of the suspension sys-
tem or front end structure.
• Installation of a tire of different size
and construction from the tires specified on the vehicle placard
attached to the driver’s door pillar or
specified for individual vehicle mod- els in this Owner’s Manual.
• Attachment of any equipment (side steps or side sill protectors, etc.)
other than genuine Toyota acces-
sory parts to the side body.
We recommend that you always con-
sult your Toyota dealer if you want to install any accessory parts on your
vehicle.
NOTICE
■SRS Airbag System Servicing
●When discarding an airbag module or scrapping the entire vehicle dam-
aged by a collision, we recommend
that you consult your Toyota dealer.
●If you need service or repair in
areas indicated in the following list, we recommend that you have the
work performed by an authorized
Toyota dealer. The SRS airbag con- trol module, impact sensors and
airbag modules are stored in the
following areas.
• Under the center of the instrument
panel
• On both the right and left sides at
the front of the vehicle
• Steering wheel and column and nearby areas
• Bottom of the steering column and nearby areas
• Top of the dashboard on front pas- senger’s side and nearby areas
• Each front seat and nearby area
• Inside each center pillar
• Inside each door
• In each roof side (from the front pil- lar to a point over the rear seat)
• Between the rear seat cushion and rear wheel house on each side
In the event that the SRS airbag sys- tem is deployed, we recommend that
you have the system replaced with
genuine Toyota parts at an authorized Toyota dealer.
SRS airbag

1864-5. EyeSight
WA R N I N G
●Tires that are unevenly worn or tires
with uneven wear patterns are
installed.*1
●Tires that are the wrong size are
installed.*1
●A flat tire has been fixed temporarily
with a tire repair kit.
●The suspension has been modified
(including a genuine Toyota sus-
pension that has been modified).
●An object that ob structs the stereo
camera’s view is installed on the vehicle.
●Tire chains are installed.
●The headlights are dirty or they
have snow and ice or dirt on them. (Objects are not correctly illumi-
nated and are difficult to detect.)
●The optical axes are not aligned
correctly. (Objects are not correctly
illuminated and are difficult to detect.)
●The lights including headlights and fog lights have been modified.
●Vehicle operation has become unstable due to an accident or mal-
function.
●The brake system warning light is
illuminated in red.*2
●A heavy cargo is inside the vehicle.
●The maximum num ber of occu- pants is exceeded.
●The meter is not operating properly; such as when the lights do not illu-
minate, the beeps do not sound, the
display is different from when it is normal, etc.*3
*1: The wheels and tires have func-
tions that are critically important.
Be sure to use the correct ones.
(P.375)
*2: If the brake system warning light
(red) does not turn off, immediately
pull the vehicle over in a safe place
and contact any authorized Toyota
retailer or Toyota authorized
repairer, or any reliable repairer to
have the system inspected.
*3: For details about the meter, refer to
P.88.
Adaptive Cruise Control is designed for use on expressways, freeways,
toll roads, motorways and similar lim-
ited access roads. It is not intended to be used in city traffic. In the following
conditions, do not use Adaptive
Cruise Control. Doin g so may result in an accident.
●Ordinary roads (roads other than those mentioned above)
• Depending on the driving environ-
ment (complexity of roads and other factors), the system may not
be able to perform as the traffic
conditions require, and that may result in an accident.
●Sharp curves or winding roads
●Frozen roads, snow-covered roads
or other slippery road surfaces
• The tires may spin, causing loss of
control of the vehicle.
●Traffic conditions when frequent
acceleration and deceleration make
it difficult to maintain the following
distance
• It may not be possible for the sys-
tem to perform as the traffic condi-
tions require.

211
4
4-5. EyeSight
Driving
WA R N I N G
• Fluid has not been fully wiped off
the windshield during or after use of
the window washer.
• Obstacles cannot be correctly rec-
ognized due to water droplets from rain or the washer, or the wiper
blades obstructing the stereo cam-
era’s field of view.
• The stereo camera’s field of view is
obstructed.
• With low obstacles (low wall, crash
barrier, low vehicle, etc.)
• The size and height of an obstacle
is smaller than the limitations of the
stereo camera’s recognition capa- bility. (Small animals, children,
pedestrians who are sitting or lying
down, etc.)
• The rear portion nearest your vehi-
cle is too small or too close (such as a trailer or oncoming vehicle).
The system may not recognize the
part of that vehicle which is closest to you.
• There is a fence or wall, etc., with a uniform pattern (striped pattern,
brick, etc.) or with no pattern in
front.
• There is a wall or door made of glass or a mirror in front.
• An obstacle (another vehicle, motorcycle, bicycle, pedestrian,
animal or child, etc.) cuts in from
the side or jumps out suddenly.
• Your vehicle is immediately behind
an obstacle after changing lanes.
• On sharp curves, steep uphill
grades or steep downhill grades
●The system determines that steer-
ing operation by the driver is intended as evasive action.
●For your safety, do not test Pre-Col-lision Throttle Management on its
own. It may operate improperly and
cause an accident.
NOTICE
In the following situations, turn off Pre-Collision Throttle Management.
Otherwise Pre-Collision Throttle Man-
agement may activate unexpectedly.
●The vehicle is being towed.
●The vehicle is being loaded onto a
carrier.
●A chassis dynamometer, free-roll-
ers or similar equipment is being
used.
●A mechanic lifts up the vehicle,
starts the engine and allows the wheels to spin freely.
●Driving on a race track

2384-6. Using other driving systems
bicycle carrier, bumper guard) are
attached. • Parts that emit high frequency sound,
such as a horn or speaker, are
attached.
●Vehicle conditions:
• Ice, snow or mud is adhered to the sonar sensors or the rear bumper
near the sonar sensor.
• The vehicle is significantly inclined. • The ground clearance is significantly
reduced due to the vehicle’s loading
condition, etc. • When the sonar sensor is misaligned
due to a collision or an accident.
●Surrounding environment:
• A cloth banner, flag, hanging branch
or railroad crossing bars are present in the reversing direction.
• When reversing on a gravel or grassy
area. • When reversing in an area where
objects or walls are adjacent to the
vehicle such as narrow tunnels, nar- row bridges, narrow roads or narrow
garages.
• Wheel track or hole is present in the ground of the reversing direction.
• When reversing over a drainage cover
(grating cover).
• The path of the reversing direction is
inclined such as on a steep uphill.
• When reversing downhill.
• Reversing in a garage with a low ceil-
ing or a tunnel.
• A curb or step is present in the revers-
ing direction.
• There is a patch of snow rearward.
• There is a puddle of water.
• There is an obstacle that is next to an
object.
• Going back along a wall.
• The area where the road starts touch-
ing dirt and snow.
• When reversing on an uneven road.
●In circumstances su ch as the follow- ing, it may not be possible to avoid a
collision even when the system oper-
ates normally. • Roads are slippery.
• The tire air pressure is not correct.
• The tires have become worn. • Tire chains are installed.
• Tires which are not the designated
size are installed. • Emergency repairs were performed
using a puncture repair kit.
• The suspension was modified. • Vehicle driving is unstable due to acci-
dent or malfunction.
• The brake system warn ing light is illu-
minated.

259
4
4-6. Using other driving systems
Driving
WA R N I N G
■The ABS does not operate effec-
tively when
●The limits of tire gripping perfor- mance have been exceeded (such
as excessively worn tires on a snow
covered road).
●The vehicle hydroplanes while driv-
ing at high speed on wet or slick
roads.
■Stopping distance when the ABS
is operating may exceed that of normal conditions
The ABS is not designed to shorten
the vehicle’s stopping distance. Always maintain a safe distance from
the vehicle in front of you, especially
in the following situations:
●When driving on dirt, gravel or
snow-covered roads
●When driving with tire chains
●When driving over bumps in the
road
●When driving over roads with pot-
holes or uneven surfaces
■TRC may not operate effectively
when
Directional control and power may not be achievable while driving on slip-
pery road surfaces, even if the TRC
system is operating. Do not drive the vehicle in conditions where stability
and power may be lost.
■When the VSC and/or brake LSD
function is activated
The slip indicator flashes. Always drive carefully. Reckless driving may
cause an accident. Exercise particular
care when the indicator flashes.
■When the TRC/VSC systems are turned off
Be especially careful and drive at a
speed appropriate to the road condi- tions. As these are the systems to
help ensure vehicle stability and driv-
ing force, do not turn the TRC/VSC systems off unless necessary.
■Replacing tires
Make sure that all tires are of the
specified size, brand, tread pattern
and total load capacity. In addition, make sure that the tires are inflated to
the recommended tire inflation pres-
sure level.
The ABS, TRC and VSC systems will
not function correctly if different tires
are installed on the vehicle. Contact any authorized Toyota retailer
or Toyota authorized repairer, or any
reliable repairer for further information when replacing tires or wheels.
■Handling of tires and the suspen-sion
Using tires with any kind of problem
or modifying the suspension will affect the driving assist systems, and may
cause a system to malfunction.

2604-7. Driving tips
4-7.Driving tips
Use fluids that are appropriate to
the prevailing out side tempera-
tures.
• Engine oil
• Engine coolant
• Washer fluid
 Have a service technician
inspect the condition of the bat-
tery.
 Have the vehicle fitted with four
snow tires or purchase a set of
tire chains for the rear tires.
Make sure to install 4 tires that are of
the specified size, and that all 4 tires
are the same size, same maker, same
brand and tread pattern. Also, make
sure to use tire chains that match the
size of the tires.
Winter driving tips
Carry out the necessary prepa-
rations and inspections before
driving the vehicle in winter.
Always drive the vehicle in a
manner appropriate to the pre-
vailing weather conditions.
Preparation for winter
WA R N I N G
■Driving with snow tires
Observe the following precautions to
reduce the risk of accidents.
Failure to do so may result in a loss of vehicle control and cause death or
serious injury.
●Use tires of the specified size, and that are the same size, same
maker, same brand and tread pat-
tern.
●Maintain the recommended level of
air pressure.
●Do not drive at speeds in excess of
the speed limit or the speed limit specified for the snow tires being
used.
●Use snow tires on a ll, not just some
wheels.
■Driving with tire chains
●When any of the tires are punc-
tured, you can seal the tire tempo- rarily. However, do not use the tire
chain on a sealed tire. If any of the
rear tires are punctured although it is required to use tire chains, con-
tact any authorized Toyota dealer or
repairer, or another duly qualified and equipped professional.
●Observe the following precautions to reduce the risk of accidents.
Failure to do so may result in the
vehicle being unable to be driven safely, and may cause death or
serious injury.
• Do not drive in excess of the speed limit specified for the tire chains
being used, or 30 km/h (19 mph),
whichever is lower.
• Avoid driving on bumpy road sur-
faces or over potholes.
• Avoid sudden acceleration, abrupt
steering, sudden braking and shift- ing operations that cause sudden
engine braking.
• Slow down sufficiently before enter- ing a curve to ensure that vehicle
control is maintained.

3026-3. Do-it-yourself maintenance
Replace the tires if the treadwear indi-
cators are showing on a tire.
■When to replace your vehicle’s
tires
Tires should be replaced if:
●The treadwear indicators are showing on a tire.
●You have tire damage such as cuts, splits, cracks deep enough to expose
the fabric, and bulges indicating inter-
nal damage
●A tire goes flat repeatedly or cannot
be properly repaired due to the size or location of a cut or other damage
If you are not sure, consult with any
authorized Toyota dealer or repairer, or another duly qualified and equipped pro-
fessional.
■Tire life
Any tire over 6 years old must be checked by a qualified technician even if
it has seldom or never been used or
damage is not obvious.
■Low profile tires
Generally, low profile tires will wear
more rapidly and tire grip performance
will be reduced on snowy and/or icy roads when compared to standard tires.
Be sure to use snow tires or tire chains
on snowy and/or icy roads and drive
carefully at a speed appropriate for road and weather conditions.
■If the tread on snow tires wears
down below 4 mm (0.16 in.)
The effectiveness of the tires as snow tires is lost.
WA R N I N G
■When inspecting or replacing
tires
Observe the following precautions to prevent accidents.
Failure to do so may cause damage
to parts of the drive train as well as dangerous handling characteristics,
which may lead to an accident result-
ing in death or serious injury.
●Make sure to insta ll 4 tires that are
of the specified size, and that all 4
tires are the same size, same maker, same brand and tread pat-
tern.
●Do not use tire sizes other than
those recommended by Toyota.
●Only use radial tires.
●Do not mix summer, all season and snow tires.
●Do not use tires that have been used on another vehicle.
Do not use tires if you do not know
how they were used previously.
NOTICE
■Low profile tires
Low profile tires may cause greater
damage than usual to the tire wheel when sustaining impact from the road
surface. Therefore, pay attention to
the following:
●Be sure to use proper tire inflation
pressure. If tires are under-inflated, they may be damaged more
severely.
●Avoid potholes, uneven pavement,
curbs and other road hazards. Fail-
ure to do so may lead to severe tire and wheel damage.

3046-3. Do-it-yourself maintenance
pressure has been adjusted.
●Tire inflation pressure changes with
temperature. The displayed values
may also be different from the values measured using a tire pressure
gauge.
■Situations in which the tire pres-
sure warning system may not oper- ate properly
●In the following cases, the tire pres-sure warning system may not operate
properly.
• If non-genuine Toyota wheels are used.
• A tire has been replaced with a tire
that is not an OE (Original Equipment) tire.
• A tire has been replaced with a tire
that is not of the specified size. • Tire chains, etc. are equipped.
• An auxiliary-supported run-flat tire is
equipped. • If a window tint that affects the radio
wave signals is installed.
• If there is a lot of snow or ice on the vehicle, particularly around the wheels
or wheel housings.
• If the tire inflation pressure is extremely higher than the specified
level.
• If tires not equipped with tire pressure warning valves and transmitters are
used.
• If the ID code on the tire pressure warning valves and transmitters is not
registered in the tire pressure warning
computer.
●Performance may be affected in the
following situations. • When driving near a TV tower, electric
power plant, gas station, radio station,
large display, airport or other facility
that generates strong radio waves or electrical noise
• When carrying a portable radio, cellu-
lar phone, cordless phone or other wireless communication device
If tire position information is not correctly
displayed due to the radio wave condi- tions, the display ma y be corrected by
driving and changing the radio wave
conditions.
●When the vehicle is parked, the time
taken for the warning to start or go off
could be extended.
●When tire inflation pressure declines
rapidly for example when a tire has burst, the warning may not function.
■Warning performance of the tire
pressure warning system
The warning of the tire pressure warning system will change in accordance with
driving conditions. For this reason, the
system may give a warning even if the tire pressure does not reach a low
enough level, or if the pressure is higher
than the pressure that was adjusted to when the system was initialized.
When replacing tires or wheels, tire
pressure warning valves and trans-
mitters must also be installed.
When new tire pressure warning
valves and transmitters are
installed, new ID codes must be
registered in the tire pressure warn-
ing computer and the tire pressure
warning system must be initialized.
Have tire pressu re warning valve
and transmitter ID codes regis-
tered by any authorized Toyota
retailer or Toyota authorized
repairer, or any reliable repairer.
( P. 3 0 6 )
■Replacing tires and wheels
If the ID code of the tire pressure warn-
ing valve and transmitter is not regis- tered, the tire pressure warning system
will not work properly. After driving for
about 10 minutes, the tire pressure warning light blinks for 1 minute and
Installing tire pressure warn-
ing valves and transmitters