2022 TOYOTA GR86 light

3226-3. Do-it-yourself maintenance
rag.
2 Pull the cover to disengage
each claw and remove it.
3 Turn the bulb base
counterclockwise.
4 Remove the light bulb.
5 Install a new light bulb then
install the bulb base to the light
unit by inserting it and turning
the bulb base clockwise.
6 Install the cover.
Align the cover with the claws on the
vehicle and push the cover toward the
front of the vehicle to engage each claw and install it.

323
6
6-3. Do-it-yourself maintenance
Maintenance and care
7 Install the clips.
■Rear fog lights
1 Remove the clips.
To prevent damage to the vehicle,
cover the tip of the screwdriver with a rag.
2 Pull the cover to disengage
each claw and remove it.
3 Turn the bulb base
counterclockwise.
4 Remove the light bulb.
5 Install a new light bulb then
install the bulb base to the light
unit by inserting it and turning
the bulb base clockwise.
6 Install the cover.
Align the cover with the claws on the
vehicle and push the cover toward the front of the vehicle to engage each claw

3246-3. Do-it-yourself maintenance
and install it.
7 Install the clips.
WA R N I N G
■Replacing light bulbs
●Turn off the lights. Do not attempt to
replace the bulb immediately after
turning off the lights. The bulbs become very hot and may cause
burns.
●Do not touch the glass portion of
the light bulb with bare hands.
When it is unavoidable to hold the glass portion, use and hold with a
clean dry cloth to avoid getting
moisture and oils on the bulb. Also, if the bulb is scratched or dropped,
it may blow out or crack.
●Fully install light bulbs and any
parts used to secure them. Failure
to do so may result in heat damage, fire, or water entering the light unit.
This may damage the lights or
cause condensation to build up on the lens.
■When changing the rear fog light or back-up lights
●Stop the engine and wait until the
exhaust pipes and surrounding parts have cooled down suffi-
ciently. The lights are located near
the exhaust pipe and touching a hot exhaust pipe and surrounding parts
can cause burns.
■To prevent damage or fire
●Make sure bulbs are fully seated
and locked.
●Check the wattage of the bulb
before installing to prevent heat damage.

7
325
When trouble arises
7
When trouble arises
.7-1. Essential information
Emergency flashers .......... 326
If your vehicle has to be
stopped in an emergency
....................................... 326
If the vehicle is submerged or
water on the road is rising
....................................... 327
7-2. Steps to take in an emer-
gency
If your vehicle needs to be
towed .............................. 329
If you think something is wrong
....................................... 334
Fuel pump shut off system
....................................... 335
If a warning light turns on or a
warning buzzer sounds... 336
If a warning message is dis-
played ............................. 344
If you have a flat tire ......... 345
If the engine will not start .. 355
If you lose your keys ......... 356
If the fuel filler door cannot be
opened ........................... 357
If the electronic key does not
operate properly ............. 357
If the vehicle battery is dis-
charged .......................... 359
If your vehicle overheats ... 362
If the vehicle becomes stuck
....................................... 364

3267-1. Essential information
7-1.Essential information
Press the switch.
All the turn signal lights will flash.
To turn them off, press the switch once
again.
■Emergency flashers
If the emergency flashers are used for a long time while the engine is not operat-
ing, the battery may discharge.
1 Steadily step on the brake pedal
with both feet and firmly depress
it.
Do not pump the brake pedal repeat-
edly as this will increase the effort required to slow the vehicle.
2 Shift the shift lever to N.
If the shift lever is shifted to N
3 After slowing down, stop the
vehicle in a safe place by the
road.
4 Stop the engine.
If the shift lever cannot be shifted
to N
3 Keep depressing the brake
pedal with both feet to reduce
vehicle speed as much as possi-
ble.
4 To stop the engine, press and
hold the engine switch for 2 con-
secutive seconds or more, or
Emergency flashers
The emergency flashers are
used to warn other drivers
when the vehicle has to be
stopped on the road due to a
breakdown, etc.
Operating instructions
If your vehicle has to be
stopped in an emer-
gency
Only in an emergency, such as
if it becomes impossible to
stop the vehicle in the normal
way, stop the vehicle using the
following procedure:
Stopping the vehicle

333
7
7-2. Steps to take in an emergency
When trouble arises
If the engine does not start, turn the
engine switch to ON.
9 Shift the shift lever to N and
release the parking brake.
Vehicles with an automatic transmis-
sion: When the shift lever cannot be shifted: P. 1 4 4
■Towing eyelet purpose
The towing eyelet is to be used to tow your vehicle, not to tow other vehicles.
■While towing
If the engine is not running, the power
assist for the brakes and steering will not function, making steering and brak-
ing more difficult.
■Wheel nut wrench
Wheel nut wrench is installed in trunk. ( P.346)
■Rear towing eyelet
If the towing eyelet is installed to the
rear, it can be used in an emergency to tow a vehicle lighter than your vehicle on
a normal road, using a rope.
■When towing another vehicle
For vehicles with BSD/RCTA, make sure
to turn BSD/RCTA off.
As the radar waves will be blocked by the towed vehicle, this system will not
operate properly.
■When installing a towing eyelet to
the rear
When installing a towing eyelet to the
rear, install it using the following proce-
dure.
1 Take out the wheel nut wrench,
flathead screwdriver and towing eye- let. ( P.346)
2 Remove the eyelet cover using a
flathead screwdriver.
To protect the bodywork, place a rag between the screwdriver and the vehicle
body as shown in the illustration.
3 Remove the cover from the bumper.
4 Insert the towing eyelet into the hole and tighten partially by hand.
5 Tighten down the towing eyelet
securely using a wheel nut wrench
or hard metal bar.

3367-2. Steps to take in an emergency
■Brake system warning light (warning buzzer)
■Vacuum pressure system warning light
■High coolant temperature warning light (warning buzzer)
If a warning light turns on or a war ning buzzer sounds
Calmly perform the following actions if any of the warning lights
comes on or flashes. If a light comes on or flashes, but then goes
off, this does not necessarily indicate a malfunction in the system.
However, if this continues to occur, have the vehicle inspected by
any authorized Toyota retailer or Toyota authorized repairer, or any
reliable repairer.
Actions to the warning lights or warning buzzers
Warning lightDetails/Actions
(red)
Indicates that:
 The brake fluid level is low; or
 The brake system is malfunctioning
This light also comes on when the parking brake is not released. If
the light turns off after the parki ng brake is fully released the sys-
tem is operating normally.
 Immediately stop the vehicle in a safe place and contact
any authorized Toyota retailer or Toyota authorized
repairer, or any reliable repairer. Continuing to drive the
vehicle may be dangerous.
Warning lightDetails/Actions
(yellow)
Indicates a malfunction in the vacuum pressure system.
 Have the vehicle inspected by any authorized Toyota
retailer or Toyota authorized repairer, or any reliable
repairer immediately.
Warning lightDetails/Actions
Indicates that the engine coolant temperature is too high
 Immediately stop the vehicle in a safe place.
Handling method ( P.362)

337
7
7-2. Steps to take in an emergency
When trouble arises
■Charging system warning light
■Low engine oil pressure warning light
■Malfunction indicator lamp
■SRS warning light (warning buzzer)
Warning lightDetails/Actions
Indicates a malfunction in the vehicle’s charging system
 Immediately stop the vehicle in a safe place and contact
any authorized Toyota retailer or Toyota authorized
repairer, or any reliable repairer.
Warning lightDetails/Actions
Indicates that the engine oil pressure is too low
 Immediately stop the vehicle in a safe place and contact
any authorized Toyota retailer or Toyota authorized
repairer, or any reliable repairer.
Warning lightDetails/Actions
Indicates a malfunction in:
 The electronic engine control system;
 The electronic throttle control system; or
 The electronic automatic transmission control system (if
equipped)
 Have the vehicle inspected by any authorized Toyota
retailer or Toyota authorized repairer, or any reliable
repairer immediately.
Warning lightDetails/Actions
Indicates a malfunction in:
 The SRS airbag system; or
 The seat belt pretensioner system
 P. 5 3