2022 TOYOTA BZ4X door lock

245
5
Owners Manual_Europe_M42D76_en
5-2. Driving procedures
Driving
■Customization
If the smart entry & start system has been deactivated in a customized set-ting, refer to P.542.
1 Stop the vehicle completely.
2 Set the parking brake. (P.254)
3 Press the P position switch.
( P.248)
Check that the shift position indicator
shows P and the parking brake indica- tor is illuminated.
4 Press the power switch.
The EV system will stop, and the meter display will be extinguished (the shift
position indicator will be extinguished a few seconds after the meter display).
5 Release the brake pedal and
check that “ACCESSORY” or
“POWER ON” is not shown on
the meter.
■When the shift control system mal-
functions
When attempting to turn the power switch off while there is a malfunction in
the shift control system, the power switch mode may change to ACC. In this case, ACC may be turned off by apply-
ing the parking brake and pressing the power switch again. If there is a mal-function in the system, have the vehicle
inspected by any authorized Toyota retailer or Toyota authorized repairer, or any reliable repairer immediately.
■Automatic P position selection
function
 P. 2 5 0
WARNING
■When starting the EV system
Always start the EV system while sit- ting in the driver’s seat. Do not
depress the accelerator pedal while starting the EV system under any cir-cumstances.
Doing so may cause an accident resulting in death or serious injury.
■Caution while driving (some models)
If EV system failure occurs while the
vehicle is moving, do not lock or open the doors until the vehicle reaches a safe and complete stop. Otherwise,
the steering lock function will activate and this may lead to an accident, resulting in death or serious injury.
NOTICE
■When starting the EV system
If the EV system becomes difficult to start, have your vehicle checked by any authorized Toyota retailer or
Toyota authorized repairer, or any reli- able repairer immediately.
■Symptoms indicating a malfunc-tion with the power switch
If the power switch seems to be oper-
ating somewhat differently than usual, such as the switch sticking slightly, there may be a malfunction. Contact
any authorized Toyota retailer or Toyota authorized repairer, or any reli-able repairer immediately.
Stopping the EV system

255
5
Owners Manual_Europe_M42D76_en
5-2. Driving procedures
Driving
ing brake manually. (P.254)
■Turning the automatic mode
off
While the vehicle is stopped and
depressing the brake pedal, press
and hold the parking brake switch
until a buzzer sounds and message
is shown on the multi-information
display.
■Parking brake operation
●When the power switch is not in ON, the parking brake cannot be released using the parking brake switch.
●When the power switch is not in ON, automatic mode (automatic brake set-
ting and releasing) is not available.
■Parking brake automatic release function
When all of the following conditions are
met in manual mode, the parking brake can be released by depressing the accelerator pedal.
●The driver’s door is closed
●The driver is wearing the seat belt
●The shift position is in a forward driv-
ing position or reverse driving position
●The malfunction indicator lamp or brake system warning light is not illu-minated.
When depressing the accelerator pedal, depress it slowly.
If the parking brake is not released when
the accelerator pedal is depressed, release the parking brake manually.
■Parking brake automatic lock func-tion
The parking brake will be set automati- cally under the following conditions:
●The brake pedal is not depressed
●The driver’s door is open
●The driver’s seat belt is not fastened
●The shift position is in a position other
than P or N (The shift position is in P during advanced park operation.) (If
equipped)
●The malfunction indicator lamp or
brake system warning light are not illuminated
■If “Parking Brake Temporarily Unavailable” is displayed on the
multi-information display
If the parking brake is operated repeat- edly over a short period of time, the sys-
tem may restrict operation to prevent overheating. If this happens, refrain from operating the parking brake. Normal
operation will return after about 1 min- ute.
■If “Parking Brake Unavailable” is displayed on the multi-information
display
Operate the parking brake switch. If the message does not disappear after oper-
ating the switch several times, the sys- tem may be malfunctioning. Have the vehicle inspected by any authorized
Toyota retailer or Toyota authorized repairer, or any reliable repairer.
■Parking brake operation sound
When the parking brake operates, a
motor sound (whirring sound) may be heard.
This does not indicate a malfunction.
■Parking brake indicator light
●Depending on the power switch mode, the parking brake indicator light will
turn on and stay on as described below:ON: Comes on until the parking brake
is released. Not in ON: Stays on for approximately 15 seconds.
●When the power switch is turned off with the parking brake set, the parking
brake indicator light will stay on for about 15 seconds.This does not indicate a malfunction.

323
5
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Driving
functions of the system cannot oper-
ate: P. 2 8 1
■LTA control when operation is can- celed
When emergency driving stop system
operation is canceled, LTA control may also be canceled.
If driving operations are not
detected after the hands off steer-
ing wheel warning operates, a
buzzer will sound intermittently and
a message will be displayed to
warn the driver, and the system will
judge if the driver is responsive or
not. If driving operations, such as
holding the steering wheel, are not
performed within a certain amount
of time, the system will enter warn-
ing phase 2.
Vehicles with a driver monitor cam-
era: Depending on the type of
detection of the driver’s unrespon-
siveness, the system may skip
warning phase 1 and start the con-
trol of warning phase 2.
After entering warning phase 2, a
buzzer will sound in short intervals
and a message will be displayed to
warn the driver, and the vehicle will
slowly decelerate. If driving opera-
tions, such as holding the steering
wheel, are not performed within a
certain amount of time, the system
will determine that the driver is not
responsive and enter the decelera-
tion stop phase.
The audio system will be muted until
the driver becomes responsive.
When the vehicle is decelerating, the
brake lights may illuminate, depending
on the road conditions, etc.
After the vehicle has decelerated a cer-
tain amount, the emergency flashers
(hazard lights) will flash.
After the driver is judged as being
not responsive, a buzzer will sound
continuously and a message will be
displayed to warn the driver, and
the vehicle will slowly decelerate
and stop. While the vehicle is
decelerating, the emergency flash-
ers (hazard lights) will flash to warn
other drivers of the emergency.
After the vehicle is stopped, the
parking brake will be applied auto-
matically. After entering the stop
and hold phase, the buzzer will
continue sounding continuously, the
emergency flashers (hazard lights)
will flash to warn other drivers of
the emergency, and the doors will
unlock.
Warning phase 1
Warning phase 2
Deceleration stop phase
Stop hold phase

367
5
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Driving
WARNING
●Depending on the condition of the road surface or the vehicle, the dis-
tance between the vehicle and a parking space, etc., it may not be possible to detect a parking space
or the system may not be able to provide assistance to the point the vehicle is fully parked.
●This system will guide the vehicle to appropriate positions for changing
the direction of travel, however, if you feel that the vehicle is approaching too close to an adja-
cent parked vehicle at any time, depress the brake pedal and change the shift position. However,
if this is performed, the number of times the vehicle changes direction may increase, and the vehicle may
be parked at an angle.
●As following objects may not be
detected, make sure to check the safety of the area around your vehi-cle and depress the brake pedal to
stop the vehicle if it may collide with an object.
• Thin objects such as wire, fences, rope, etc.
• Cotton, snow and other materials that absorb sound waves
• Sharply-angled objects
• Low objects (curb stones, parking
blocks, etc.)
• Tall objects with upper sections that
protrude outward
●Even if there is an object in the tar-
get parking space, it may not be detected and assistance may be performed.
●While the system is operating, if it is likely that your vehicle will collide with a nearby vehicle, parking
block, object, or person, depress the brake pedal to stop the vehicle and press the Advanced Park main
switch to disable the system.
●Never use only the multimedia dis-
play to view the area behind the vehicle. The image displayed may differ than the actual situation.
Using only the screen when back- ing up may lead to an accident, such as a collision with another
vehicle. When backing up, make sure to look directly or use the mir-rors to check the safety of the area
around your vehicle, especially behind the vehicle.
●When the ambient temperature is extremely low, the screen may appear dark or the displayed image
may become unclear. Also, as mov- ing objects may appear distorted or may not be able to be seen on the
screen, make sure to directly check the safety of the area around your vehicle.
●In the following situations, while the vehicle is stopped and held by
Advanced Park, it may be canceled and the vehicle may start moving. Immediately depress the brake
pedal. Failure to do so may lead to an accident.
• When the driver’s door is opened
• When operations instructed by the
system are not performed within a certain amount of time
• When the brake pedal is depressed and the vehicle is stopped for a cer-tain amount of time
• When the system malfunctions
●As the steering wheel will turn while this system is operating, pay atten-tion to the following.

370
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
WARNING
●Rem ot e co nt r o l f u nc t io n i s a sys t em which assists in remote parking or
exiting operations using a smart- phone. When using Remote con-trol function, the driver must carry
the electronic key and smartphone and confirm the safety of the area around the vehicle.
●While using Remote control func-tion, the vehicle can be stopped by
stop continuously operating the smartphone (stopping movement of your finger, removing your finger
from the screen, etc.). The vehicle can also be stopped by touching the cancel button on the smart-
phone application, unlocking the doors using the electronic key, or opening a door.
●If it seems like your vehicle may contact an obstruction, etc., stop
operating the smartphone and can- cel Remote control function if nec-essary.
●System operation will only be per-formed at a fixed speed and the
vehicle cannot be accelerated or decelerated even if the speed of continuous operation of the smart-
phone is increased or decreased.
●Never drive the vehicle while star-
ing at the smartphone screen.
●When driving, make sure to directly
check the safety of the area around your vehicle.
●Do not use Remote control function when passengers or pets are in the vehicle.
●In an emergency, the system can be canceled by operating a switch
on the electronic key or by opening a door.
●To use Remote control function, it is necessary to have a smartphone with the latest version of the
Remote Park app. The following operating systems are supported:
• Android™
• Apple® iOS
●When registering the vehicle to the Remote Park smartphone app, dis-
connect any other apps which are connected to the vehicle.
●To enable Remote control function, make sure to disable the Apple CarPlay connection.
●When parking, make sure that the vehicle can be parked in the target
parking space before beginning operation.
●Only use Remote control function on level road surfaces which are not slick. Do not use Remote con-
trol function for parking spaces on a downward or upward incline.
●While Remote control function is operating, if a malfunction or sys-tem limitation is detected, the fol-
lowing will occur automatically:
• Remote control function will be can-
celed
• The vehicle will stop
• The shift position will change to P and the parking brake will be
engaged
• The power switch will turn off (for
some malfunctions, the power switch will not turn off or cannot be turned off. Enter the vehicle and
take corrective action according to the message displayed on the smartphone.)
• The doors will remain locked

371
5
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Driving
WARNING
●When starting Remote control func- tion, unlock the doors with wireless
remote control by electronic key.
●When Remote control function is
operating, the driver should remain within approximately 3 m (9.8 ft.) of the vehicle. If the driver becomes
more than approximately 3 m (9.8 ft.) away, Remote control function will be suspended and a message
will be displayed on the smart- phone. Remote control function operation can be resumed by
approaching the vehicle.
●The headlights will be turned on if
the surrounding area is dark.
●If system operation is canceled due
to a malfunction, the emergency flashers will flash.The emergency flashers will turn off
if any of the following conditions are met:
• A door is opened
• 3 minutes have elapsed since the
emergency flashers began flashing
●Remote control function can only
be started when the following con- ditions are met:
• When the EV system is starting, after assist mode is selected
• When the power switch is off
• When the remote air conditioning is
operating
●After unlocking the doors using the
wireless remote control, if the doors are locked using the smart entry function, the lock operation may be
delayed.
NOTICE
■Precautions for use Advanced Park
If the 12-volt battery was discharged or has been removed and installed, fold and extend the outside rear view
mirrors.
■When using Remote control
function
●Check the battery charge level of
the smartphone before using Remote control function. If the bat-tery of the smartphone dies while
operating Remote control function, assist will be suspended. Also, if the battery charge level of the
smartphone is 20% or less when attempting to start Remote control function, Remote control function
will not be started.
●Turn on the Bluetooth communica-
tion function of the smartphone before using Remote control func-tion. Remote control function can-
not be used if the Bluetooth function is off.
●Do not turn off the Bluetooth func-tion of the smartphone or discon-nect from the multimedia system
while using Remote control func- tion. If the vehicle cannot be con-nected to via Bluetooth, Remote
control function cannot be used.
●While using Remote control func-
tion, if a call is received, etc., and another app is opened, Remote control function will be suspended.
Assist can be resumed if the Remote Park app is reopened within 3 minutes. If 3 minutes or
more elapse, assist will be can- celed.

374
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
• When a camera lens is dirty or cov-
ered with water droplets
●In situations such as the following, the
target parking space may not be rec- ognized correctly:• When there marks from repairs or
other marks on the road surface, or there is a parking block, traffic bollard, or other object on the road surface
• When it is raining or has rained and the road surface is wet and reflective or there are puddles
• When the area around the vehicle is dark or backlit• When the color or brightness of the
road surface is uneven • When the parking space is on a slope• When there are diagonal lines (access
aisle) near the parking space • When the appearance of the parking space is affected by the shadow of a
parked vehicle (such as shadows from the grille, side step, etc.)• When accessories which obstruct the
view of the camera are installed • When the parking space lines are faded or dirty, making them unclear
• When the appearance of the parking space is affected by the shadow of the vehicle or trees
■Sensor detection information
 P. 3 3 5
■Objects which the sensor may not be properly detected
 P. 3 3 5
■Situations in which the sensor may
not operate properly
 P. 3 3 5
■Situations in which parking assis- tance may not operate even if there
is no possibility of a collision
 P. 3 3 6
Press the Advanced Park main
switch.
If the switch is pressed while assistance
is being performed, the assistance will
be canceled.
■Operating conditions of the
Advanced Park
Assistance will begin when all of the fol- lowing conditions are met:
●The brake pedal is depressed
●The vehicle is stopped
●The driver’s seat belt is fastened
●The steering wheel is not being oper-ated
●The accelerator pedal is not depressed
●All of the doors are closed
●The outside rear view mirrors are not folded
●The parking brake is not engaged
●The dynamic radar cruise control are
not operating
●ABS, VSC, TRAC, PCS and PKSB
are not operating
●The vehicle is not on a steep slope
●The VSC and TRAC are not turned off
If assistance cannot be started, check
the message displayed on the multime-
dia display ( P.400)Turning the Advanced Park
on/off

392
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
6From outside of the vehicle,
confirm the parking space on
the screen of the smartphone
and then select the start button.
Start operation of Remote control func-
tion while standing approximately 50 cm (1.6 ft.) or more from the vehicle and out of the path of the vehicle.
7 Checking the safety of the area
around the vehicle, trace the
operation area on the screen of
the smartphone continuously,
the vehicle will move and park-
ing assistance will be per-
formed.
If operation of the screen of the smart-
phone is stopped, assistance can be suspended and the vehicle can be stopped. The doors are automatically
locked before the vehicle starts moving.
8 When the parking space is
reached, after the vehicle is
stopped by the parking brake,
the shift position will be changed
to P, the power switch will be
turned off, and the doors will be
locked.
A completion screen will be displayed on the smartphone
■The parking function can be used
even if obstructions exist if
●When using the parking functions at a
parking space made of white lines, even if an obstruction exists in the parking space, the space can be set
as the target parking space. This allows for assistance to continue after setting a parking space from inside
the vehicle and then exiting the vehi- cle to move an obstruction, such as a traffic cone placed in a handicapped
parking space.
●When perpendicular parking using
Advanced Park, 3 parking spaces on each side of the vehicle (up to 6 total) can be detected. However, when
using Remote control function, only 1 parking space on each side of the vehicle can be detected
After the vehicle is stopped, assis-
tance can be provided to move the
vehicle into a garage, etc., by using
the forward and backward move-
ment function.
1 Stop the vehicle at the location
you would like to start assis-
tance.
2 Press the Advanced Park main
switch. ( P.374)
3 Select and then select
[Forward/reverse].
4 Select [OK].
5 Exit the vehicle while carrying
the electronic key and smart-
phone, and then start the
Remote Park app on the smart-
phone.
Moving the vehicle forward
and backward using Remote
control function