2022 TOYOTA BZ4X brake

537
8
Owners Manual_Europe_M42D76_en
8-2. Steps to take in an emergency
When trouble arises
may get dirty.
24Store the bottle in the luggage
compartment while it is con-
nected to the compressor.
25 Taking precautions to avoid sud-
den braking, sudden accelera-
tion and sharp turns, drive
carefully at under 80 km/h (50
mph) to the nearest authorized
Toyota retailer or Toyota autho-
rized repairer, or any reliable
repairer that is less than 100 km
(62 miles) away for tire repair or
replacement.
For repair and replacement of a tire or disposal of the tire puncture repair kit, contact any authorized Toyota retailer
or Toyota authorized repairer, or any reliable repairer.
When having the tire repaired or
replaced, make sure to tell any autho- rized Toyota retailer or Toyota autho-rized repairer, or any reliable repairer
that the sealant is injected.
■If the tire is inflated to more than the specified air pressure
1 Disconnect the hose from the valve.
2 Install the air release cap to the end of the hose and push the protrusion
on the air release cap into the valve to let some air out.
3 Disconnect the hose from the valve,
remove the air release cap from the hose and then reconnect the hose.
4 Turn the compressor switch on and wait for several seconds, then turn it
off. Check that the air pressure indi- cator shows the specified air pres-sure is reached. ( P.559)
If the air pressure is under the desig- nated pressure, turn the compres-sor switch on again and repeat the
inflation procedure until the specified air pressure is reached.
■After a tire is repaired with the emergency tire puncture repair kit
●The tire pressure warning valve and transmitter should be replaced.
●Even if the tire inflation pressure is at the recommended level, the tire pres-
sure warning light may come on/flash.
WARNING
■When fixing the flat tire
●Stop your vehicle in a safe and flat
area.
●Do not touch the wheels or the area
around the brakes immediately after the vehicle has been driven. After the vehicle has been driven,
the wheels and the area around the brakes may be extremely hot. Touching these areas with hands,
feet or other body parts may result in burns.

540
Owners Manual_Europe_M42D76_en
8-2. Steps to take in an emergency
system.
 The EV system may be malfunc-
tioning due to an electrical prob-
lem such as electronic key
battery depletion or a blown fuse.
However, depending on the type
of malfunction, an interim mea-
sure is available to start the EV
system. ( P.540)
 There is a possibility that the
temperature of the traction bat-
tery is extremely low (approxi-
mately below -30°C [-22°F]).
( P.87, 244)
*: It may not be possible to shift the shift
position from P.
One of the following may be the
cause of the problem:
 The 12-volt battery may be dis-
charged. ( P.544)
 The 12-volt battery terminal con-
nections may be loose or cor-
roded. ( P.473)
One of the following may be the
cause of the problem:
 One or both of the 12-volt battery
terminals may be disconnected.
( P.473)
 The 12-volt battery may be dis-
charged. ( P.544)
Contact any authorized Toyota retailer
or Toyota authorized repairer, or any
reliable repairer if the problem cannot
be repaired, or if repair procedures are
unknown.
When the EV system does not
start, the following steps can be
used as an interim measure to start
the EV system if the power switch
is functioning normally.
Do not use this starting procedure
except in cases of emergency.
1 Set the parking brake.
2 Turn the power switch to ACC.*
3Press and hold the power switch
for about 15 seconds while
depressing the brake pedal
firmly.
Even if the EV system can be
started using the above steps, the
system may be malfunctioning.
Have the vehicle inspected by any
authorized Toyota retailer or Toyota
authorized repairer, or any reliable
repairer.
*: Setting can be customized. ( P.567)
The interior lights and head-
lights are dim, or the horn
does not sound or sounds at
a low volume.
The interior lights and head-
lights do not turn on, or the
horn does not sound.
Emergency start function

543
8
Owners Manual_Europe_M42D76_en
8-2. Steps to take in an emergency
When trouble arises
in order to perform the following
operations:
1 Locks all the doors
2 Unlocks all the doors
■Key linked functions
1 Closes the windows (turn and hold)*
2Opens the windows (turn and hold)*
*: These settings must be customized at
any authorized Toyota retailer or
Toyota authorized repairer, or any reli-
able repairer.
1 Depress the brake pedal.
2 Touch the electronic key to the
power switch.
When the electronic key is detected, a buzzer sounds and the power switch
will turn to ON. When the smart entry & start system is deactivated in customization setting,
the power switch will turn to ACC.
3 Firmly depress the brake pedal
and check that is shown on
the multi-information display.
4 Press the power switch.
In the event that the EV system still cannot be started, contact any autho-rized Toyota retailer or Toyota autho-
rized repairer, or any reliable repairer.
WARNING
■When using the mechanical key and operating the power win-
dows
Operate the power window after checking to make sure that there is no
possibility of any passenger having any of their body parts caught in the window.
Also, do not allow children to operate the mechanical key. It is possible for children and other passengers to get
caught in the power window.
Starting the EV system

544
Owners Manual_Europe_M42D76_en
8-2. Steps to take in an emergency
■Stopping the EV system
Set the parking brake, shift the shift
position to P and press the power switch as you normally do when stopping the EV system.
■Electronic key battery
As the above procedure is a temporary measure, it is recommended that the electronic key battery be replaced
immediately when the battery is depleted. ( P.499)
■Alarm (if equipped)
Using the mechanical key to lock the
doors will not set the alarm system. If a door is unlocked using the mechani-cal key when the alarm system is set,
the alarm may be triggered. ( P. 7 7 )
■Changing power switch modes
Release the brake pedal and press the power switch in step 3 above.
The EV system does not start and modes will be changed each time the switch is pressed. ( P.246)
If you have a set of jumper (or
booster) cables and a second vehi-
cle with a 12-volt battery, you can
jump start your vehicle by following
the steps below.
1 Confirm that the electronic key
is being carried.
When connecting the jumper (or
booster) cables, depending on the situ- ation, the alarm may activate and the doors may lock. ( P.78)
2Open the hood (P.467).
3 Open the positive (+) battery ter-
minal cover.
While pressing on the claw, open the
If the 12-volt batter y is
discharged
The following procedures may
be used to start the EV system
if the vehicle’s 12-volt battery
is discharged.
You can also call any autho-
rized Toyota retailer or Toyota
authorized repairer, or any reli-
able repairer.
Restarting the EV system

551
8
Owners Manual_Europe_M42D76_en
8-2. Steps to take in an emergency
When trouble arises
1Stop the EV system. Set the
parking brake and shift the shift
position to P.
2 Remove the mud, snow or sand
from around the front wheels.
3 Place wood, stones or some
other material under the front
wheels to help provide traction.
4 Restart the EV system.
5 Shift the shift position to D or R
and release the parking brake.
Then, while exercising caution,
depress the accelerator pedal.
■When it is difficult to free the vehi-
cle
Press the switch to turn off TRC.
( P.407)
If the vehicle becomes
stuck
Carry out the following proce-
dures if the tires spin or the
vehicle becomes stuck in mud,
dirt or snow:
Recovering procedure
WARNING
■When attempting to free a stuck vehicle
If you choose to push the vehicle back and forth to free it, make sure the surrounding area is clear to avoid
striking other vehicles, objects or peo- ple. The vehicle may also lunge for-ward or lunge back suddenly as it
becomes free. Use extreme caution.
■When shifting the shift position
Be careful not to shift the shift position with the accelerator pedal depressed.This may lead to unexpected rapid
acceleration of the vehicle that may cause an accident resulting in death or serious injury.
NOTICE
■To avoid damage to the transmis-sion and other components
●Avoid spinning the tires and depressing the accelerator pedal more than necessary.
●If the vehicle remains stuck even
after these procedures are per- formed, the vehicle may require towing to be freed.

558
Owners Manual_Europe_M42D76_en
9-1. Specifications
*: The fluid capacity is a reference quantity.
If replacement is necessary, contact any authorized Toyota reta iler or Toyota
authorized repairer, or any reliable repairer.
*: The fluid capacity is the quantity of reference.
If replacement is necessary, contact any authorized Toyota reta iler or Toyota
authorized repairer, or any reliable repairer.
Charging rates:
Quick charge
Slow charge
15 A max.
5 A max.
Front eAxle
Fluid capacity*3.9 L (4.1 qt., 3.4 Imp.qt.)
Fluid typee-Transaxle Fluid TE
NOTICE
■Front eAxle fluid type
Using transaxle fluid other than the above type may cause abnor mal noise or
vibration, or ultimately damage the front eAxle of your vehicle .
Rear eAxle (AWD models)
Fluid capacity*3.1 L (3.3 qt., 2.7 Imp. qt.)
Fluid typee-Transaxle Fluid TE
NOTICE
■Rear eAxle fluid type
Using transaxle fluid other than the above type may cause abnor mal noise or
vibration, or ultimately damage the rear eAxle of your vehicle.
Brakes
Pedal clearance*158 mm (2.28 in.) Min.*3
62 mm (2.44 in.) Min.*4
Pedal free play1.0 - 6.0 mm (0.04 - 0.24 in.)

559
9
Owners Manual_Europe_M42D76_en
9-1. Specifications
Vehicle specifications
*1: Minimum pedal clearance when depressed with a force of 300 N (31 kgf, 66 lbf)
while the EV system is operating.
*2: Make sure to confirm that the brake system warning light (yell ow) does not illumi-
nate. (If the brake system warning light illuminates, refer to P.515)
*3: Left-hand drive vehicles
*4: Right-hand drive vehicles
18-inch tires
20-inch tires
Parking brake indicator*2
When pushing the parking brake switch for 1 to
4 seconds: turns off
When pulling the parking brake switch for 1 to 4
seconds: comes on
Fluid typeSAE J1703 or FMVSS No.116 DOT 3
SAE J1704 or FMVSS No. 116 DOT 4
Steering
Free playLess than 30 mm (1.2 in.)
Tires and wheels
Tire size235/60R18 103H
Tire inflation pressure
(Recommended cold tire inflation
pressure)
Front: 260 kPa (2.6 kgf/cm2 or bar, 38 psi)
Rear: 260 kPa (2.6 kgf/cm2 or bar, 38 psi)
Wheel size18  7 1/2 J
Wheel bolt torque140 N•m (14.3 kgf•m, 103 ft•lbf)
Tire size235/50R20 104V XL
Tire inflation pressure
(Recommended cold tire inflation
pressure)
Front: 260 kPa (2.6 kgf/cm2 or bar, 38 psi)
Rear: 260 kPa (2.6 kgf/cm2 or bar, 38 psi)
Wheel size20  7 1/2 J
Wheel bolt torque140 N•m (14.3 kgf•m, 103 ft•lbf)

561
9
Owners Manual_Europe_M42D76_en
9-2. Customization
Vehicle specifications
9-2.Customiz ation
■Changing using the multi-
information display
1 Press or of the meter
control switches and select .
2 Press or of the meter
control switches, select the item.
3 To switch the function on and
off, press icon to switch to
the desired setting.
4 To perform detailed setting of
the function, press and hold
and display the setting screen.
The method of detailed setting differs
for each screen. Please refer to the advice sentence displayed on the screen.
To go back to the previous screen or
exit the customize mode, press .
■Changing by using the multi-
media system
1 Select on the main menu
2 Select “Vehicle customize”.
3 According to the display, select
the desired setting.
Various setting can be changed.
Refer to the list of settings that can be
changed for details.
■When customizing using the multi-
media system or multi-information display
Stop the vehicle in a safe place, apply
the parking brake, and shift the shift position to P. Also, to prevent 12-volt battery discharge, leave the EV system
operating while customizing the fea- tures.
Some function settings are changed simultaneously with other fu nctions
being customized. Contact any authorized Toyota retailer or Toy ota autho-
rized repairer, or any reliable repairer for further details.
Customizable features
Your vehicle includes a variety
of electronic features that can
be personalized to your prefer-
ences. The settings of these
features can be changed by
using the multi-information
display, multimedia system, at
any authorized Toyota retailer
or Toyota authorized repairer,
or any reliable repairer.
Customizing vehicle fea-
tures
NOTICE
■During customization
To prevent 12-volt battery discharge, ensure that the EV system is operat-
ing while customizing features.
Customizable features