2022 TOYOTA BZ4X display

315
5
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Driving
system is operating, if a speed limit
sign is detected, the detected
speed limit will be displayed with an
up/down arrow. The set speed can
be increased/reduced to the
detected speed limit by pressing
and holding the “+” switch or “-”
switch.
Press and hold the “+” switch.
Press and hold the “-” switch.
■The dynamic radar cruise control with road sign assist may not oper-
ate properly when
As the dynamic radar cruise control with road sign assist may not operate prop-
erly in situations where the RSA may not operate or cannot detect signs correctly ( P.304), when using this function,
make sure to confirm the actual speed limit.
In the following situations, the set speed
may not change to the detected speed limit by pressing and holding the “+” switch or “-” switch:
●When speed limit information is not available
●When the detected speed limit is the same as the set speed
●When the detected speed limit is out-side of the speed range which the
dynamic radar cruise control system can operate
The settings of Dynamic radar
cruise control can be changed
through customize settings.
( P.568)
When the set speed is lower
than the detected speed
limit
When the set speed is
higher than the detected
speed limit
Changing Dynamic radar
cruise control settings

316
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
■Meter display
Set vehicle speed
Cruise control indicator
■Switches
Driving assist switch
Driving assist mode select
switch
Cancel switch
“-” switch
“+” switch/“RES” switch
1 Press the driving assist mode
select switch to select cruise
control.
Cruise control
The vehicle can be driven at a
set speed even if the accelera-
tor pedal is not depressed.
Use the cruise control only on
highways and expressways.
WARNING
■For safe use
●Driving safely is solely the responsi-
bility of the driver. Therefore, do not overly rely on this system. The driver is solely responsible for pay-
ing attention to the vehicle’s sur- roundings and driving safely.
●Set the speed appropriately accord-ing to the speed limit, traffic flow, road conditions, weather condi-
tions, etc. The driver is responsible for confirming the set speed.
■Situations in which cruise con-trol should not be used
Do not use the cruise control in the
following situations. As the system will not be able to provide appropriate control, using it may lead to an acci-
dent resulting in death or serious injury.
●On roads with sharp bends
●On winding roads
●On slippery roads, such as those covered with rain, ice or snow
●On steep downhills, or where there are sudden changes between sharp
up and down gradients Vehicle speed may exceed the set speed when driving down a steep hill.
●When it is necessary to disable the system: P.275
System components
Setting the vehicle speed

317
5
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Driving
The cruise control indicator will illumi-
nate.
2 Using the accelerator pedal,
accelerate to the desired vehicle
speed (approximately 30 km/h
[20 mph] or more), and press
the driving assist switch to set
the set vehicle speed.
The vehicle speed at the moment the
switch is released will be the set vehicle speed.
■Adjusting the set vehicle
speed using the switches
To change the set vehicle speed,
press the “+” or “-” switch until the
desired speed is displayed.
1 Increase set vehicle speed
2 Decrease set vehicle speed
The set vehicle speed will increase
or decrease as follows:
Short press adjustment: By 1 km/h (0.6
mph) or 1 mph (1.6 km/h) each time the
switch is pressed
Long press adjustment: Increases con-
tinuously while the switch is pressed
and held
■Increasing the set vehicle
speed using the accelerator
pedal
1 Depress the accelerator pedal
to accelerate the vehicle to the
desired vehicle speed.
2 Press the “+” switch.
Adjusting the set vehicle
speed
Canceling/resuming control

318
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
1Press the cancel switch or driv-
ing assist switch to cancel con-
trol.
Control will also be canceled if the brake pedal is depressed.
2 Press the “RES” switch to
resume control.
■Automatic cancelation of the cruise
control
In the following situations, the cruise control will be canceled automatically:
●When the vehicle speed drops approximately 16 km/h (10 mph) or
more below the set vehicle speed
●When the vehicle speed drops below
approximately 30 km/h (20 mph)
●When the brake control or output
restriction control of a driving support system operates (For example: PCS, drive-start control)
●When the parking brake has been operated
●Situations in which some or all of the functions of the system cannot oper-
ate: P. 2 8 1
*: If equipped
■Meter display
Set vehicle speed
Speed limiter indicator
Speed limiter*
A desired maximum speed can
be set using the speed limiter
switch. The speed limiter pre-
vents the vehicle speed from
exceeding the set speed.
WARNING
■Situations in which speed limiter should not be used
●Situations in which the sensors may
not operate properly: P.279
●When it is necessary to disable the
system: P.275
System Components

319
5
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Driving
■Switches
Driving assist switch
Driving assist mode select
switch
Cancel switch
“-” switch
“+” switch/“RES” switch
1 Press the driving assist mode
select switch to select the speed
limiter.
The speed limiter indicator will illumi- nate in white.
2 Accelerate or decelerate to the
desired vehicle speed, and
press the driving assist switch to
set the maximum vehicle speed.
The speed limiter indicator will change
from illuminated in white to green.
The set vehicle speed will be displayed on the multi-information display in
green.If the vehicle speed is set while driving at below approximately 30 km/h (20 mph), the set vehicle speed will be
set to approximately 30 km/h (20 mph).
Press the cancel switch or driving assist switch to cancel control.
The system does not start when the shift position is R.
The system does not start when the driving assist switch is pressed continu-ously.
To change the set vehicle speed,
press the “+” or “-” switch until the
desired speed is displayed.
1 Increase set vehicle speed
Setting the maximum vehi-
cle speed
Adjusting the set vehicle
speed

320
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
2Decrease set vehicle speed
Short press adjustment: Press the
switch
Long press adjustment: Press and hold
the switch until the desired set vehicle
speed is reached.
The set vehicle speed will increase or
decrease as follows:
Short press adjustment: By 1 km/h (0.6
mph) or 1 mph (1.6 km/h) each time the
switch is pressed
Long press adjustment: Increases or
decreases in 5 km/h (3.1 mph) or 5
mph (8 km/h) increments continuously
while the switch is pressed and held
The set vehicle speed adjustment
increment can be changed through a
customize setting.
1 Press the cancel switch or driv-
ing assist switch to cancel con-
trol.
2 Press the “RES” switch to
resume control.
When control is canceled, the speed
limiter indicator will change from illumi- nated in green to white.
■Exceeding the set speed
In the following situations, if the vehicle
speed exceeds the set vehicle speed, the displayed set vehicle speed will flash:
●When the accelerator pedal is deeply depressed
●When driving down a slope
■Automatic cancellation of the speed limiter
●Situations in which some or all of the functions of the system cannot oper-
ate: P. 2 8 1
■Changes in brake operation sound and pedal response
 P. 4 0 8
When RSA function is enabled and
the speed limiter is operating, if a
speed limit sign is detected, the
detected speed limit will be dis-
played with an up/down arrow. The
set vehicle speed can be
increased/reduced to the detected
speed limit by pressing and holding
the “+” or “-” switch.
■When the set veh icle speed is
lower than the detected speed
limit
Press and hold the “+” switch.
Canceling/resuming control
Speed limiter with Road
Sign Assist

323
5
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Driving
functions of the system cannot oper-
ate: P. 2 8 1
■LTA control when operation is can- celed
When emergency driving stop system
operation is canceled, LTA control may also be canceled.
If driving operations are not
detected after the hands off steer-
ing wheel warning operates, a
buzzer will sound intermittently and
a message will be displayed to
warn the driver, and the system will
judge if the driver is responsive or
not. If driving operations, such as
holding the steering wheel, are not
performed within a certain amount
of time, the system will enter warn-
ing phase 2.
Vehicles with a driver monitor cam-
era: Depending on the type of
detection of the driver’s unrespon-
siveness, the system may skip
warning phase 1 and start the con-
trol of warning phase 2.
After entering warning phase 2, a
buzzer will sound in short intervals
and a message will be displayed to
warn the driver, and the vehicle will
slowly decelerate. If driving opera-
tions, such as holding the steering
wheel, are not performed within a
certain amount of time, the system
will determine that the driver is not
responsive and enter the decelera-
tion stop phase.
The audio system will be muted until
the driver becomes responsive.
When the vehicle is decelerating, the
brake lights may illuminate, depending
on the road conditions, etc.
After the vehicle has decelerated a cer-
tain amount, the emergency flashers
(hazard lights) will flash.
After the driver is judged as being
not responsive, a buzzer will sound
continuously and a message will be
displayed to warn the driver, and
the vehicle will slowly decelerate
and stop. While the vehicle is
decelerating, the emergency flash-
ers (hazard lights) will flash to warn
other drivers of the emergency.
After the vehicle is stopped, the
parking brake will be applied auto-
matically. After entering the stop
and hold phase, the buzzer will
continue sounding continuously, the
emergency flashers (hazard lights)
will flash to warn other drivers of
the emergency, and the doors will
unlock.
Warning phase 1
Warning phase 2
Deceleration stop phase
Stop hold phase

324
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
*: If equipped
Meter control switches
Turning the Blind Spot Monitor on/off.
Outside rear view mirror indica-
tors
When a vehicle is detected in a blind
spot of the outside rear view mirrors or
approaching rapidly from behind into a
blind spot, the outside rear view mirror
indicator on the detected side will illumi-
nate. If the turn signal lever is operated
toward the detected side, the outside
rear view mirror indicator flashes.
Driving assist information indica-
tor
Illuminates when the Blind Spot Monitor
is turned off. At this time, “Blind Spot
Monitor OFF” will be displayed on the
multi-information display.
■Outside rear view mirror indicator
visibility
In strong sunlight, the outside rear view mirror indicator may be difficult to see.
■Customization
Some functions can be customized. ( P.570)
■Certification
 P. 6 4 3
BSM (Blind Spot Moni-
tor)*
The Blind Spot Monitor is a
system that uses rear side
radar sensors installed on the
inner side of the rear bumper
on the left and right side to
assist the driver in confirming
safety when changing lanes.
WARNING
■Cautions regarding the use of
the system
●The driver is solely responsible for safe driving. Always drive safely,
taking care to observe your sur- roundings.
●The Blind Spot Monitor is a supple-mentary function which alerts the driver that a vehicle is in a blind
spot of the outside rear view mirrors or is approaching rapidly from
behind into a blind spot. Do not overly rely on the Blind Spot Moni-tor. As the function cannot judge if it
is safe to change lanes, over reli- ance could lead to an accident resulting in death or serious injury.
As the system may not function cor- rectly under certain conditions, the
driver’s own visual confirmation of safety is necessary.
System components