2022 MERCEDES-BENZ GLC COUPE service

#
Drain o. any excess engine oil that has been
added. Todo so, consult a quali/ed specialist
wo rkshop.
R For engine oil level turn on ignition #
Switch on theve hicle tocheck the engine oil
le ve l.
R Engine oil level System inoperative: The oil
le ve l sensor is defective or not connected. #
Consult a quali/ed specialist workshop.
R Engine oil level System currently unavail. #
Close the bonnet.
T
T op up engine oil
op up engine oil &
W
W ARNING
ARNING Risk of burns from hot compo-
nent parts in the engine compartment
Cer tain component parts in the engine com-
partment can be very hot, e.g. the engine, the
cooler and parts of theex haust system. #
Allow the engine tocool down and only
to uch component parts described in the
fo llowing. &
W
WARNING
ARNING Risk of /re and injury from
engine oil
If engine oil comes into contact with hot com-
ponent parts in the engine compartment, it
may ignite. #
Make sure that no engine oil is spilled
next tothe /ller opening. #
Allow the engine tocool o. and thor-
oughly clean the engine oil from compo-
nent parts before starting theve hicle. *
N
NOOTE
TE Engine damage caused byan inco r-
re ct oil /lter, incor rect oil or additi ves #
Do not use engine oils or oil /lters which
do not cor respond tothe speci/cations
ex plicitly prescribed forth e service inter-
va ls. #
Follow the inst ructions on the service
inter val display forch anging the engine
oil and obser vethe prescribed change
inter vals. #
Do not use additives. *
N NOOTE
TE Damage caused bytopping up too
much engine oil To
o much engine oil can damage the engine or
th e catalytic con verter. #
Have excess engine oil remo ved at a
qu ali/ed specialist workshop. %
Depending on driving st yle, theve hicle con-
sumes up to0.8 litre of oil per 1000 km. The
oil consum ption may be higher than this when
th eve hicle is new or if you frequently drive at
high engine speeds. Maintenance and care
333
333

P
P
aint
aint
R Insect remains: Soak with insect remo ver and
ri nse o. the treated areas aTer wards.
R Bird droppings: Soak with water and rinse o.
aTer wards.
R Tree resin, oils, fuels and greases: remo veby
ru bbing gently with a clo thsoaked in petro-
leum ether or lighter 0uid.
R Coolant and brake 0uid: remo vewith a damp
clo thand clean water.
R Tar stains: use tarre mo ver.
R Wax: use silicone remo ver.
R Do not attach sti ckers, /lms or similar materi-
als. Only ha ve/lm attached tothe bumper at
a quali/ed specialist workshop.
R Remo vedirt immediatel y,where possible.
Matt
Matt /nish
/nish
R Only use care products appr ovedfor
Mercedes-Benz.
R Do not attach stic kers, /lms or similar materi-
als. Only ha ve/lm attached tothe bumper at
a qu ali/ed specialist workshop. R
Do not polish theve hicle and light-alloy
wheels.
R Only use car washes that cor respond tothe
latest engineering standards.
R Do not use car wash prog rammes with a /nal
hot wax treatment.
R Do not use paint cleaners, bu1ng or polishing
products, gloss preser vers,e. g. wa x.
In theev ent of paintwork damage:
R Always ha vepaintwork repairs car ried out at a
qu ali/ed specialist workshop.
R Make sure thera dar sensors function
(/ page 213). N No
ot
tes on cleaning decor
es on cleaning decor ativ
ative f
e foils
oils Obser
vethe no tes on matt /nish care in thech ap-
te r "No tes on paintwork/matt /nish paintwork
care" (/ page 337). They also apply tomatt dec-
orative foils.
Obser vethe no tes on cleaning decorative foils to
av oid damage. Cleaning
Cleaning
R For cleaning, use plenty of water and a mild
cleaning agent without additives or abrasive
substances (e.g. a car shampoo appr ovedfor
Mercedes-Benz).
R Remo vedirt as soon as possible. Avoid rub-
bing too hard in order tonot ir reparably dam-
age the decorative foil.
R Ifth ere is dirt on the /nish or if the decorative
fo il is dull: Use thePa int Cleaner recommen-
ded and appr ovedfo r Mercedes-Benz.
R Insect remains: Soak with insect remo ver and
ri nse o. the treated areas aTer wards.
R Bird droppings: Soak with water and rinse o.
aTer wards.
R Toprev ent water stains, dry a foil-wrapped
ve hicle with a soT, absorbent clo thaTer every
car wash.
Av
Av oiding damag
oiding damag e t
e to t
o t he decor
he decor ativ
ative f
e foil
oil
R The service life and colouring of decorative
fo ils are impaired by:
- Sunlight
- Temp erature (e.g. hot air blo wer) 338
338
Maintenance and care

#
Pump up the tyre again.
ATer a maximum of ten minutes the tyre pres-
sure must be at least 200 kPa (2.0 bar/
29 psi). &
W
W ARNING ARNING Risk of accident due tothe
speci/ed tyre pressure not being attained
If th e speci/ed tyre pressure is not attained
aTer the speci/ed time, the tyre is too badly
damaged. The tyre sealant cannot repair the
tyre in this instance.
The braking and driving characteristics may be
gr eatly impaired. #
Do not continue driving. #
Consult a quali/ed specialist workshop. If,
If,
aTer
aTer t
ten minut
en minut es, a tyr
es, a tyr e pr
e pressur
essur e of 200 kPa
e of 200 kPa
(2.0 bar/29 psi) has been att
(2.0 bar/29 psi) has been att ained:
ained:#
Switch o. the tyre in0ation compressor. #
Unscr ewthe /lling hose from theva lve of the
defective tyre. &
W
WARNING
ARNING Risk of accident from driving
with sealed tyres
A tyre temp orarily sealed with tyre sealant
impairs the handling characteristics and is not
suitable for higher speeds. #
Adapt your driving style accordingly and
drive carefull y. #
Do not exceed the maximum speed limit
with a tyre that has been repaired using
tyre sealant. #
Obser vethe maximum permissible speed of
80 km/h for a tyre sealed with tyre sealant.
* N
NOOTE
TE Staining from leaking tyre sealant ATer use,
excess tyre sealant may leak out
from the /lling hose. #
Therefore, place the /lling hose in the
plastic bag that contained the TIREFIT
kit. +
ENVIR
ENVIR ONMENT
ONMENT AL NO
AL NOTE
TEEnvironmental
pollution caused byenvironmentally ir re-
sponsible disposal Ty
re sealant contains pollu tants. #
Have the tyre sealant bottle disposed of
professionall y,e.g. at a Mercedes-Benz
Service Centre. #
Stow the tyre sealant bottle and the tyre in0a-
tion compressor. #
Pull away immediatel y. #
Stop driving aTer appr oximately ten minutes
and check the tyre pressure using the tyre
in0ation compressor.
The tyre pressure must now be at least
130 kPa (1.3 bar/19 psi). &
W WARNING
ARNING Risk of accident due tothe
speci/ed tyre pressure not being attained
If th e speci/ed tyre pressure is not reached,
th e tyre is too badly damaged. The tyre seal-
ant cannot repair the tyre in this instance. Breakdown assistance
349
349

&
W
W ARNI NG
ARNI NGRisk of explosion from a frozen
battery
A dischar ged battery may freeze at temp era-
tures slightly abo veor below freezing point.
During starting assistance or battery charging,
battery gas can be released. #
Always allow a battery tothaw before
ch arging it or per form ing starting assis-
ta nce. If
th e indicator/warning lamps in the inst rument
cluster do not light up at low temp eratures, it is
ve ry likely that the dischar ged battery has frozen.
In this case you may neither jump-start theve hi-
cle nor charge the batter y.
The service life of a bat tery that has been thawed
may be dramatically shor tened. The starting char-
acteristics may be impaired, especially at low
te mp eratures.
It is recommended that you ha veath awe d battery
ch ecked at a quali/ed specialist workshop. Plug-in h
Plug-in h ybr
ybrid
id
If yo ur vehicle has been star ted with starting
assistance, it may not be possible touse the elec-
tric drive for appr oximately 30 minutes.
St arting assis tance is not considered tobe a nor-
mal operating condition.
All v
All v ehicles ehicles
* NO
NOTE
TEDamage caused bynume rous or
ex tended attem ptsto start the engine Numerous or
extended attem ptsto start the
engine may damage the catalytic con verter
due tonon-combusted fuel. #
Avoid numerous and extended attem pts
to start the engine. Obser
vethefo llowing points during starting assis-
ta nce and when charging the batter y:
R Only use undamaged jump lead/charging
cables with a su1cient cross-section and
insulated term inal clamps.
R Non-insulated parts of thete rm inal clamps
must not come into contact with other me tal parts while
the jump lead/charging cable is
connected tothe battery/jump-start connec-
tion point.
R The jump lead/charging cable must not come
into contact with any parts which may mo ve
when the engine is running.
R Always make sure that nei ther you nor the bat-
te ry is electros tatically charge d.
R Keep awa y from /re and naked 0ames.
R Do not lean overth e batter y.
Obser vethe additional following points when
ch arging the batter y:
R Only use battery charge rs tested and
appro vedfo r Mercedes-Benz.
R Read the battery charge r's operating inst ruc-
tions before charging the batter y.
Obser vethe additional following points during
starting assistance:
R Starting assis tance may only be pr ovided
using vehicles, batteries or other jump start
devices with a nominal voltage of 12 V.
R The vehicles must not touch. Breakdown assistance
353 353

#
Insert lid 4into the brac ket at there ar of the
fuse box. #
Fold down lid 4ofthe fuse box and tighten
scr ews3. #
Fold down co ver1. #
Turn reta ining clip 2on co ver1 aqu arter-
turn clockwise. #
Close the bonnet. Opening and closing t
Opening and closing t
he fuse bo
he fuse box in t
x in the coc
he coc kpit
kpit R
Obser vethe no tes on elect rical fuses
(/ page 361).
The fuse box is on the driver's side on the side of
th e cockpit under a co ver. #
Toopen and close it, consult a Mercedes-Benz
Service Centre. Opening and closing t
Opening and closing t
he fuse bo
he fuse box in t
x in the fr
he front
ont
passeng
passeng er f
er f oo
ootw
twell
ell Obser
vethe no tes on elect rical fuses
(/ page 361). #
T To open: o open: open cover1 inthe direction of the
ar ro w and remo veit. #
T To close:
o close: reinsert co ver1. Opening and closing t Opening and closing t
he fuse bo
he fuse box in t
x in the load com-
he load com-
par
par tment
tment Obser
vethe no tes on elect rical fuses
(/ page 361). #
Open the load compartment 0oor . #
T
To open:
o open: fold co ver1 up in the direction of
th e ar row.
The fuse assignment dia gram is on the side of the
fuse box. #
T
To close:
o close: fold down co ver1. Breakdown assistance
363
363

*
N
N O
OTE
TE Damage tocomponents of theve hi-
cle body or chassis due to/tted snow
ch ains If
yo u /t snow chains tothe front wheels of
4MATIC vehicles, you may damage compo-
nents of theve hicle body or chassis. #
Only /t snow chains tothere ar wheels
of 4MATIC vehicles. Obser
vethefo llowing no tes when using snow
ch ains:
R Snow chains are only permissible for cer tain
wheel/tyre combinations. You can obtain
information about this from a Mercedes-Benz
Service Centre.
R For saf etyre asons, only use snow chains that
ha ve been speci/cally appr oved foryo ur vehi-
cle byMercedes-Benz, or snow chains with
th e same quality standard.
R Comply with the installation inst ructions of the
snow chain manu facturer.
R If snow chains are /tted, the maximum per-
missible speed is 50 km/h. R
V
V ehicles wit
ehicles wit h A
h Activ
ctiv e P
e Par
arking Assist
king Assist: :do not use
Ac tive Parking Assist when snow chains are
/tted.
R V
Vehicles wit
ehicles wit h lev
h level contr
el contr ol:
ol:if snow chains are
/tted, only drive at raised vehicle le vel
( / page 246).
% You can permanently limit the maximum
speed for driving with winter tyres
(/ page 224).
% You can deactivate ESP ®
to pull away
( / page 217). This allo ws the wheels tospin,
achieving an increased driving forc e. T
T
yr
yr e pr
e pr essure
essure N
No
ot
tes on tyr
es on tyr e pr
e pressure
essure &
W
WARNING
ARNING Risk of accident due toinsu1-
cient or excessive tyre pressure
Un derin0a tedorove rin0ated ty res pose in par-
ticular thefo llowing risks:
R The tyres can burst. R
The tyres can wearexcessively and/or
une venly.
R The driving characteristics as well as the
stee ring and braking characteristics may
be greatly impaired. #
Comply with there commended tyre
pressure and check the tyre pressure of
all tyres, including the spare wheel, regu-
lar ly:
R monthly
R when the load changes
R before embarking on a lon ger journey
R if operating conditions change, e.g. o.-
ro ad driving #
Adjust the tyre pressure, if necessar y. Ty
re pressure which is too high or too low can:
R Shor tenth e service life of the tyres.
R Cause increased tyre damage.
R Adve rsely a.ect driving characteristics and
th us driving saf ety, e.g. due toaquaplaning. Wheels and tyres
365
365

If
th e preceding tyre sizes are complemented by
th e+ symbol, the tyre pressure information
fo llowing sho wsalternative tyre pressures. Fuel
consum ption may then increase slightl y.
The load conditions "pa rtially laden" and "fully
laden" are de/ned in theta ble for di.erent num-
bers of passengers and amounts of luggage. The
actual number of seats may di.er from this. T
T
yr
yr e pr
e pr essur
essur e monit
e monit or
oring syst
ing syst em
em F
F
unction of t
unction of t he tyr
he tyre pr
e pressur
essur e monit
e monit or
oring syst
ing syst em
em
The system checks the tyre pressure and the tyre
te mp erature of the tyres /t tedtotheve hicle by
means of a tyre pressure sensor.
The tyre pressure and the tyre temp erature
appear in the on-board computer (/ page 367).
If th ere is a substantial pressure loss or if the tyre
te mp erature is excessive, you will be warned with
display messages (/ page 460) ortheh
wa rning lamp in the inst rument cluster
(/ page 485).
The tyre pressure monitoring system is only an
aid. It is the driver's responsibility toset the tyre pressure
tothere commended cold tyre pressure
suitable forth e operating situation.
In most cases, the tyre pressure monitoring sys-
te m will automatically update the new refere nce
va lues aTer you ha vechanged the tyre pressure.
Yo u can, ho wever, also update there fere nce val-
ues byrestarting the tyre pressure monitoring
system manually (/ page 368).
Syst
Syst em limits
em limits
The system may be impaired or may not function
particular lyin thefo llowing situations:
R incor rect refere nce values were ta ught in
R sudden pressure loss caused byafo re ign
object penetrating the tyre, forex ample
R there is a malfunction caused byano ther radio
signal source
Chec
Chec king t
king t he tyr
he tyr e pr
e pressur
essur e wit
e with t
h the tyr
he tyr e pr
e pressure
essure
monit
monit or
oring syst
ing syst em
em
R
R eq
equir uir ements:
ements:
R The vehicle is switched on. On-board computer:
4 Service 5
Tyres
One of thefo llowing displa ysappears:
R Current tyre pressure and tyre temp erature of
th e individual wheels: R
Tyre pressures will be displayed after a few
minutes of driving
R Tyre pressure monitor active: thete ach-in
process of the system is not yetcomple te. The
tyre pressures are already being monitored. #
Compare the tyre pressure with there com-
mended tyre pressure forth e cur rent ope rat-
ing condition (/ page 366).Additionall y, Wheels and tyres
367 367

obser
vethe no tes on cold tyres
(/ page 365).
% The values displa yed in the on-board com-
puter may deviate from those of the tyre pres-
sure gauge as they referto sea le vel.At high
ele vations, the tyre pressure values indicated
by a pressure gauge are higher than those
shown bythe on-board computer. In this case,
do not reduce the tyre pressure.
R
R est
est ar
arting t
ting t he tyr
he tyr e pr
e pressur
essur e monit
e monit or
oring syst
ing syst em
em
R
R eq
eq uir
uir ements:
ements:
R The recommended tyre pressure is cor rectly
set forth ere specti veoperating status on all of
th e wheels (/ page 365).
Re start the tyre pressure monitoring system in the
fo llowing situations:
R The tyre pressure has changed.
R The wheels or tyres ha vebeen changed or
ne wly /tted. On-board computer:
4 Service 5
Tyres #
Swipe down wards on Touch Control on the
leT-hand side of the steering wheel.
The Use current tyre pressures as new refer-
ence values? message is shown in the multi-
function displa y. #
Torestart, press Touch Control on the leT-
hand side of the steering wheel.
The Tyre press. monitor restarted message is
shown in the multifunction displa y.
Cur rent wa rning message s are deleted and
th eye llow h warning lamp goes out.
ATer you ha vebeen driving for a few minutes,
th e system checks whe ther the cur rent tyre
pressures are within the speci/ed range. The
cur rent tyre pressures are then accep ted as
re fere nce values and monitored.
Be sure toalso pay attention tothefo llowing rela-
te dto pic:
R Notes on tyre pressure (/ page 365) T
T
yr
yr e pr
e pr essur
essur e loss w
e loss w ar
arning syst
ning syst em
em F
F
unction of t
unction of t he tyr
he tyre pr
e pressur
essur e loss w
e loss w ar
arning syst
ning syst em
em
The tyre pressure loss warning system warnsthe
driver bymeans of display messages when there
is a se vere tyre pressure loss.
Syst
Syst em limits
em limits
The system may be impaired or may not function
particula rly in thefo llowing situations:
R incor rect refere nce values were ta ught in
R sudden pressure loss caused byafo re ign
object penetrating the tyre, forex ample
R aneven pressure loss on more than one tyre
occurs
The system has a restric ted or dela yed function
particular lyin thefo llowing situations:
R poor ground conditions, e.g. snow or grav el
R driving with snow chains
R when adopting a very sporty driving st yle with
high cornering speeds or sudden acceleration
R driving with a very heavy or lar getrailer
R driving with a high load 368
368
Wheels and tyres