2022 MERCEDES-BENZ EQE SALOON Owners Manual

is being
changed and not for maintenance
wo rkunder theve hicle.
R The jack must be placed on a /rm, 0at and
non-slip sur face. If necessar y,use a lar ge, 0at,
load-bearing, non-slip underla y.
R The foot ofthe jack must be positioned verti-
cally under the jack support point. Ru
les of conduct when theve hicle is raised:
R Never place your hands or feet under theve hi-
cle.
R Never lie under theve hicle.
R Do not start theve hicle and do not release the
electric parking brake.
R Do not open or close any doors or the boot
lid. #
Using the wheel wrench, loosen the wheel
bolts on the wheel you wish tochange by
about one full turn. Do not unscr ewthe
scr ews comple tely. 406 406
Wheels and tyres

Po
sition of the jack support points
* N
NOOTE
TE Mercedes-AMG vehicles #
Obser vethe no tes in the Supplement.
Yo u could otherwise failto recognise
dangers. &
W
W ARNING
ARNING Risk of injury from incor rect
positioning of the jack
If yo u do not position the jack cor rectly at the
appropriate jacking point of theve hicle, the
jack could tip wi th theve hicle raised. #
Only position the jack at the appropriate
jacking point of theve hicle. The base of th
e jack must be positioned vertically
under the jacking point of theve hicle. *
N
NOOTE
TE Damage totheve hicle due tousing
an unsuitable jack Yo
u can damage theve hicle and, in particular,
th e high-voltage battery if you use a jack that
is not speci/cal lydesigned forth e jack sup-
port points of theve hicle. #
Only use jac ksthat are speci/cal ly
designed forth e jack support points, or
use an appropriate adap ter. *
N
NO
OTE
TE Risk of damage totheve hicle due
to incor rect positioning of the jack If
yo u do not position the jack at the designa-
te d jack support points, you could damage
yo ur vehicle and, in particular, the high-voltage
batter y. #
Only position the jack at the designated
jack support points. #
Take thera tchet out of the tyre-change tool kit
and place it on the he xagon nut of the jack so
th at the letters "AUF" are visible. #
Position support 2of jack 4on jack sup-
port point 1. #
Turn ratchet 3clockwise until support 2
sits comple tely on jack support point 1and
th e base of the jack lies evenly on thegr ound. Wheels and tyres
407
407

#
Turn ratchet 3until the tyre is raised a maxi-
mum of 3 cm from thegr ound. #
Loosen and remo vethe wheel (/ page 408). R
R
emo
emo ving a wheel
ving a wheel R
R
eq
eq uir
uir ements:
ements:
R The vehicle is raised (/ page 405).
* NO
NOTE
TE Mercedes-AMG vehicles #
Obser vethe no tes in the Supplement.
Yo u could otherwise failto recognise
dangers. When
changing a wheel, avoid applying any force
to the brake discs, as this could impair the le vel of
comfort when braking.
* N
NO OTE
TE Damage tothe wheels' plastic ele-
ments when changing a wheel Plastic elements on wheels may be damaged
when removing and repositioning the wheel. #
Do not raise the wheels bythe plastic
elements when removing and reposition-
ing. *
N
NOOTE
TE Damage tothre ading from dirt on
wheel bolts #
Do not place wheel bolts in sand or on a
dirty sur face. #
Unscr ewthe uppermost wheel bolt com-
ple tely. #
Screw cent ring pin 1into theth re ad ins tead
of the wheel bolt. #
Unscr ewthere maining wheel bolts com-
ple tely. #
Remo vethe wheel. F F
itting a ne
itting a ne w wheel
w wheel R
R
eq
eq uir
uir ements:
ements:
R The wheel tobe changed is remo ved and the
cent ring pin is sc rewe d in (/ page 408).
* NO
NOTE
TEMercedes-AMG vehicles #
Obser vethe no tes in the Supplement.
Yo u could otherwise failto recognise
dangers. &
W
WARNING
ARNING Risk of accident from losing a
wheel
Oiled or greased wheel bolts can cause the
wheel bolts tocome loose, as too can dam-
aged wheel bolts or wheel hub thre ads. #
Never oil or grease theth re ads. 408
408
Wheels and tyres

#
Intheev ent of damage totheth re ads,
contact a quali/ed specialist workshop
immediatel y. #
Have the damaged wheel bolts or dam-
aged hub thre ads replaced. #
Do not continue driving. #
Obser vethe information on thech oice of tyres
(/ page 401).
Fo r tyres with a speci/ed direction of rotation, an
ar ro w on the side wall of the tyre indicates the
cor rect direction of rotation. Obser vethe direc-
tion of rotation when /tting.
* N NOOTE TE Damage tothe wheels' plastic ele-
ments when changing a wheel Plastic elements on wheels may be damaged
when removing and repositioning the wheel. #
Do not raise the wheels bythe plastic
elements when removing and reposition-
ing. #
Slide the wheel tobe mounted onto the cen-
tring pin and push it on. &
W
WARNING
ARNING Risk of injury from tightening
wheel bolts and nuts
If yo u tighten the wheel bolts or wheel nuts
when theve hicle is raised, the jack could tip. #
Only tighten wheel bolts or wheel nuts
when theve hicle is on thegr ound. #
Be sure toobser vethe inst ructions and saf ety
no tes on "Changing a wheel" (/ page 401). #
For saf etyre asons, only use wheel bolts which
ha ve been appr oved byMercedes-Benz and
fo rth e wheel in question. #
Tighten the wheel bolts evenly in a diagonal
pattern in the order indicated until they are
/nger-tight. #
Unscr ewand remo vethe centring pin. #
Tighten the last wheel bolt until it is /n ger-
tight. #
Lowe rth eve hicle (/ page 409). Low Low
er
ering t
ing t he v
he vehicle
ehicle aTer
aTera wheel c
a wheel c hange
hange R
R
eq
eq uir
uir ements:
ements:
R The new wheel has been /tted (/ page 408).
* NO
NOTE
TERisk of vehicle jack becoming trap-
ped bythe AIRMATIC system If
th e AIRMATIC system has released air when
ra ising theve hicle, the jack can become trap-
ped when theve hicle is lo wered. #
Start the drive system. This adapts the
ve hicle le vel. #
Remo vethe jack from under theve hicle. #
T
To low
o low er t
er the v
he v ehicle:
ehicle: placethera tchet onto
th e he xagon nut of the jack so that the letters
"AB" are visible and turn anti-clockwise. Wheels and tyres
409
409

#
Tighten the wheel bolts evenly in a diagonal
pattern in the order indicated 1to5 with
an initial maximum forc e of 80 Nm. #
Tighten the wheel bolts evenly in a diagonal
pattern in the order indicated 1to5 with
th e speci/ed tightening torque of 150 Nm. &
W
WARNING
ARNING Risk of accident due toincor-
re ct tightening torque
The wheels could come loose if the wheel
bolts or wheel nuts are not tightened tothe
prescribed torque. #
Ensure that the wheel bolts or wheel
nuts are tightened tothe prescribed
tightening torque. #
Ifyo u are not sure, do not mo vetheve hi-
cle. Con tact a quali/ed specialist work-
shop and ha vethe tightening torque
ch ecked immediatel y. #
Check the tyre pressure of the ne wly/tted
wheel and adjust it if necessar y.
% The following does not apply if the new wheel
is an emer gency spa rewheel. #
V
V ehicles wit
ehicles wit h a tyr
h a tyre pr
e pressur
essur e monit
e monit or
oring sy
ing sy s-
s-
t
t em:
em: restart the tyre pressure monitoring sys-
te m (/ page 400). Emerg
Emerg
ency spar
ency spar e wheel
e wheel N
No
ot
tes on t
es on t he emerg
he emerg ency spar
ency spar e wheel
e wheel &
W
WARNING
ARNING Risk of accident caused by
incor rect wheel and tyre dimensions
The wheel or tyre size and the tyre type of the
emer gency spa rewheel or spare wheel and
th e wheel tobe replaced may di.er. The emer-
ge ncy spa rewheel or spare wheel can signi/-
cantly impair driving characteristics of the
ve hicle.
To prev ent hazardous situations: #
Drive carefull y. #
Never /t more than one emer gency
spa rewheel or spare wheel that di.ers
in size. #
Only use an emer gency spa rewheel or
spare wheel brie0y. #
Do not deacti vate ESP ®
. #
Have the emer gency spa rewheel or
spare wheel of a di.erent size replaced
at the nearest quali/ed specialist work- 410
410
Wheels and tyres

shop. The new wheel must ha
vethe cor-
re ct dimensions. %
The emer gency spa rewheel is secured in the
emer gency spa rewheel bag in the boot.
Obser vethefo llowing no tes on /tting an emer-
ge ncy spa rewheel:
R The maximum permissible speed with an
emer gency spa rewheel /tted is 80 km/h.
R Do not /t the emer gency spa rewheel with
snow chains.
R Replace the emer gency spa rewheel aTer six
ye ars at the latest, rega rdless of wear.
R Use the wheel bolts that are included with the
emer gency spa rewheel.
R Check the tyre pressure of the emer gency
spa rewheel /tted. Cor rect the pressure as
necessar y.
% The speci/ed tyre pressure is stated on the
label of the emer gency spa rewheel.
% V
V ehicles wit
ehicles wit h a tyr
h a tyre pr
e pressur
essur e monit
e monit or
oring sy
ing sy s-
s-
t
t em:
em: if an emer gency spa rewheel is /tted, the
tyre pressure monitoring system cannot func- tion
reliabl y.Fo r a few minutes aTer an emer-
ge ncy spa rewheel is /tted, the system may
still display the tyre pressure of there mo ved
wheel. Only restart the system again when the
emer gency spa rewheel has been replaced
with a new wheel.
Be sure toalso obser vethefo llowing fur ther rela-
te d subjects:
R Notes on tyre pressure (/ page 397)
R Tyre pressure table (/ page 398)
R Notes on /tting tyres (/ page 401)
R Fitting an emer gency spa rewheel
(/ page 405) Wheels and tyres
411
411

N
N
o
ot
tes on t
es on t ec
echnical data
hnical data
* NO
NOTE
TEMercedes-AMG vehicles #
Obser vethe no tes in the Supplement.
Yo u could otherwise failto recognise
dangers. The
tech nical data was de term ined in accordance
with EU Directives. The data stated only applies to
ve hicles with standard equipment. You can obtain
fur ther information from a Mercedes-Benz Service
Centre.
Onl Onl y f
y for cert
or cert ain countr
ain countr ies:
ies:you can /n dvehicle-
speci/c vehicle data in theCO C documents (CER-
TIFIC ATE OF CONFORMITY). These documents
are supplied when theve hicle is deli vered. On-boar
On-boar
d electr
d electronics
onics N
No
ot
tes on t
es on t am
amper
per ing wit
ing wit h t
h the engine electr
he engine electr onics
onics *
N
NOOTE
TE Premature wearthro ugh improper
maintenance Improper maintenance may cause
vehicle
components towe ar more quickly and the
ve hicle's operating permit may be in validated. #
Always ha veworkon the engine elec-
tronics and related components car ried
out at a quali/ed specialist workshop. T
T
w
w o-wa
o-wa y r
y radios
adios N
No
ot
tes on
es on /tting
/tting tw
two-wa
o-wa y r
y radios
adios &
W
WARNING
ARNING Risk of accident due to
improper workon two-w ayradios
If two-w ayradios are manipulated or retro/t-
ted incor rectl y,the electromagnetic radiation
from the two-w ayradios can inter fere with the
ve hicle elect ronics and jeopardise the operat-
ing saf ety of theve hicle. #
You should ha veall workon electrical
and electronic components car ried out
at a quali/ed specialist workshop. &
W
WARNING
ARNING Risk of accident due to
improper operation of two-w ayradios
If yo u use two-w ayradios in theve hicle
improper ly,th eir electromagnetic radiation
can disrupt theve hicle's elect ronics. This is
th e case in thefo llowing situations, in particu-
lar:
R The two-w ayradio is not connected toan
ex terior aerial.
R The exterior aerial is /tted incor rectly or is
not a lo w-re0ection aerial.
This could jeopardise the operating saf ety of
th eve hicle. #
Have the lo w-re0ection exterior aerial /t-
ted at a quali/ed specialist workshop. #
When operating two-w ayradios in the
ve hicle, alw ays connect them tothe lo w-
re 0ection exterior aerial. 412
412
Te
ch nical data

*
N
N O
OTE
TE Inva lidation of the operating permit
due tofailure tocomply with the inst ruc-
tions for installation and use The operating permit may be in
validated if the
inst ructions for installation and use of two-w ay
ra dios are not obser ved. #
Only use appr oved frequency bands. #
Obser vethe maximum permissible out-
put po wer in these frequency bands. #
Only use appr oved aerial positions. 1
Rear roof area
On vehicles with a panoramic sliding sunroof, /t-
ting an aerial is not permitted.
Use Tech nical Speci/cation ISO/TS 21609 (Road
Ve hicles – "EMCs for installation of aTermar ket
ra dio frequency transmitting equipment") when
re tro/tting two- wayra dios. Comply with the legal
re qu irements for de tach able parts. If
yo ur vehicle has /ttings for two-w ayradio equip-
ment, use the po wer supply and aerial connectors
pr ov ided in the pre-ins tallation. Obser vethe man-
ufacturer's supplements when /tting.
T
T w
w o-wa
o-wa y r
y radio tr
adio tr ansmission output
ansmission output
The maximum transmission output (PEAK) at the
base of the aerial must not exceed theva lues in
th efo llowing table.
Fr
Fr eq
eq uency band and maximum tr
uency band and maximum tr ansmission out-
ansmission out-
put
put F
F
r
req
eq uency band
uency band Maximum tr
Maximum transmis-
ansmis-
sion output
sion output
2‑m frequency band
144 - 174 MHz 50 W
Te rrestrial Trunked
Ra dio (TETRA)
380 - 460 MHz 10 W
70‑cm frequency band
430 - 470 MHz 35 W Te
ch nical data
413 413