2022 MAZDA MODEL MX-30 EV charging

Charge connector
The charge connector is used for
connecting to the normal charge port.

When the charge connector is
connected to the normal charge port,
a vehicle system locks the charge
connector.
When the charge connector is locked
by the vehicle system, it unlocks when
the driver’s door is unlocked.
If the charge connector locked by the
vehicle system is not unlocked even
though the driver’s door is unlocked,
consult an Authorized Mazda Dealer.

The conditions for locking the system
on the vehicle side can be changed.
For the procedure to change the
conditions, refer to Charging Settings
on page 3-21.
Control box
The control box indicates the charge
status by turning on/flashing the
indicator light.
For the indicator light illumination/
fl ash pattern, refer to the instruction
manual accompanying the charge
cable.
Charge plug
The charge plug is the part for
connecting to the power supply.
Charge port
The charge port refers to the area
where the charge connector is
connected.
The component parts of the charge
port are as follows.
1. Charge indicator
2. Normal charge port
3. Normal charge port cap
4. Charge lid
5. Quick charge port cap
6. Quick charge port
Charge indicator
The charging indicator indicates the
charging status by turning on/flashing
the light.
For the charging indicator
illumination/ flash pattern, refer to
Checking Charging Status on page
3-18.
Normal charge port
The normal charge port is the part to
which the connector of the charge
cable is connected. This is used for
normal charging.
Charge lid
The charge lid is locked/unlocked in
conjunction with the door locking/
unlocking mechanism.
When unlocking the driver’s door, the
charge lid is unlocked. When locking
the driver’s door, the charge lid is
locked.
However, if the driver’s door is
unlocked using the auxiliary key, the
charge lid is not unlocked.
Before Driving
Electric Vehicles
3-13
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

NOTE
When the driver's door is locked using
any of the following functions, the
charge lid is also locked at the same
time.
Vehicle speed sensing auto door lock
function
Auto re-lock function
Quick charge port
The quick charge port is the part to
which the connector of the quick
charger is connected. This is used for
quick charging.
Battery heater
The battery heater is designed to
maintain the appropriate high voltage
battery temperature.
Because the driving performance and
the charging performance decrease if
the high voltage battery temperature
decreases, decreases in their
performance are reduced by
maintaining the appropriate high
voltage battery temperature using the
battery heater.
When the high voltage battery
temperature decreases signi ficantly
while parking or charging , the battery
heater operates. When the
temperature increases to the speci fied
value, the heater turns o ff.
However, when the high voltage
battery level is low, the battery heater
does not operate.
NOTE
Because the electrical power of the
high voltage battery is used by the
battery heater, we recommend that
the charge connector is left
connected to the vehicle when
parked in a location where charging
is available.
If the vehicle is not used for a long
period of time, we recommend that
the battery heater is turned o ff using
[Settings] in Mazda Connect.
When the battery heater operates,
the charging time could take longer.
Battery cooling
If the high voltage battery temperature
reaches 40 ℃ (104 ℉) or higher after
driving the vehicle, it is possible to cool
the high voltage battery while the
vehicle is parked for maintaining a long
high voltage battery life.
If the Excessive Battery Temperature
noti fication is displayed on the center
display after completing a trip, select
Start to operate the battery cooling.
NOTE
Because the electrical power of the
high voltage battery is used by the
battery cooling , we recommend that
the charge connector is connected to
the vehicle while the battery cooling is
operating , when parked in a location
where charging is available.
▼ Charging
Charging type
There are two methods of charging the
high voltage battery, normal charging
and quick charging.
We recommend that you use normal
charging as the preferred charging
method as this will help to keep the
high voltage battery in optimal
condition and maintain a long battery
life.

The exact charging time depends on
various conditions at the time of
charging , such as the type of charger,
battery condition, ch
arging patterns, as
well as the battery temperature and
ambient temperature. In cold weather
Before Driving
Electric Vehicles
3-14
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

conditions, both the battery and
ambient temperature will affect the
required charging time and, in certain
situations, this may lead to a signi ficant
increase in the charging time.
Normal charging
Normal Charging can be performed at
home using either a household power
source such as a wall outlet or wall
box, or similar method (alternating
current). Additionally, charging can be
performed at a public charging facility
using a charger other than a quick
charger (direct current).
When charging is started after the
remaining high voltage battery power
warning indication/warning light turns
on, the time it takes to fully charge the
high voltage battery at a public AC
charging facility is about 5 hours. Using
a household power source for charging
will increase the charging time to fully
charge the high voltage battery.
For normal charging , the charging
timer function can be used to charge
automatically from start to finish.
For details on how to use the charging
timer function, refer to Charging
Settings on page 3-21.
Quick charging
When charging is started at a quick
charging station (DC with 50 kW or
higher) the high voltage battery can be
charged from a 20% to 80% battery
charge level in about 36 minutes. The
exact charging time depends on
various conditions at the time of
charging , such as the type of charger,
battery condition, ch arging patterns, as
well as the battery temperature and
ambient temperature. In cold weather
conditions, both the battery and
ambient temperature will aff ect the
required charging time and, in certainsituations, this may lead to a significant
increase in the charging time.
WARNING
Always heed the following when
using a quick charger:
Otherwise, it could lead to an
accident.
 Do not use a charge cable which
exceeds 30 m (98 ft).
 This vehicle is compatible with quick
chargers with charge cables of 30 m
(98 ft) or shorter and which do not
charge other devices or vehicles at
the same time.

How to perform normal charging
1. Shift the selector lever to the P position.
2. Switch the power switch OFF.
3. Press the location shown in the figure to open the charge lid.
4. Open the normal charge port cap.
1. Normal charge port cap
Before Driving
Electric Vehicles
3-15
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

5. Connect the charge plug to theoutlet.
6. Connect the charge connector to the normal charge port. Charging
starts after connection is
completed.
Make sure to lock all the doors
before leaving the vehicle while
charging.
NOTE
When the charging timer is set,
charging does not start even if the
charge connector is connected.
When you prefer to start charging
immediately, use the charging
timer cancellation function.
1. Normal charge port
7. When charging is finished, remove
the charge connector.
8. Close the normal charge port cap.
9. Close the charge lid.
10.Remove the charge plug from the power supply.
Make sure to lock all the doors before
leaving the vehicle.

How to perform quick charging
1. Shift the selector lever to the P
position.
2. Switch the power switch OFF.
3. Press the location shown in the figure to open the charge lid.
4. Open the quick charge port capand normal charge port cap.
1. Quick charge port cap
2. Normal charge port cap
5. Connect the charge connector of the quick charger to the quick
charge port.
1. Quick charge port
6. Operate the quick charger to start charging.
Before Driving
Electric Vehicles
3-16
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

CAUTION
When operating a quick charger,
always use the charger according to
its instructions. If the quick charger
is operated incorrectly, the quick
charger or vehicle could be
damaged.
Make sure to lock all the doors
before leaving the vehicle while
charging.
7. When charging is finished, remove
the charge connector.
8. Close the quick charge port cap.
9. Close the charge lid.
Make sure to lock all the doors before
leaving the vehicle.
Before Driving
Electric Vehicles
3-17
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

▼Checking Charging Status
Charge indicator
The illumination/
flash pattern of the charge indicator can be checked using the
labels on the charge lid.
Charge indicator illumination/
flash pattern Content
— OFF Charging is possible.
(White) ON Turns on when waiting for starting to charge.
(White)Flashes slowly The brightness changes when the charging timer is set.
(Green)
Flashes slowly The brightness changes during charging.
(Green)
ONTurns on when charging is completed.
Tu r n s o
ff after a certain period of time has passed since charging was
completed.
(Amber) FlashesFlashes when the charging connector is connected and the selector
lever is in a position other than P.
Shift the selector lever to the P position.
(Amber)
ONTurns on if there is a problem with the charging system when the
charging connector is connected.
Wait a few minutes then reconnect the charging connector.
(Red)
ONTurns on if there is a problem with the charging system and the
charging port lid is opened or the charging connector is connected.
Have your vehicle inspected by an Authorized Mazda Dealer.
Multi-information Display
When the driver's door is opened with the charge connector connected, the
charging status is displayed on the multi-information display.
Before Driving
Electric Vehicles
3-18
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Powe r s wi tc h O F F
1. High voltage battery indication
2. Charging completion time

Powe r s wi tc h O N
1. High voltage battery indication
2. Charging completion time

IndicationContent
— Preparing to Charge Displays while the charging timer is being canceled
and when the charging connector is connected.
— Charging Scheduled Displays while in charging timer mode and when the
charging connector is connected.
Charging
Displays during charging.
Charging Complete Displays when charging is completed.
Charging Error. Shift Selector Lev-
er Not in ParkDisplays when charging is started with the selector
lever in a position other than P.
Charging Interrupted. See Own-
er's Manual for Details Displays when charging is interrupted.
Charging Error. Have the Vehicle
Inspected Displays when charging is not possible due to a
charging system problem.
NOTE
When charging is started, the charging st
atus screen is displayed for a while. The
charging status screen turns off after a certain period of time passes or the doors or
liftgate is locked.
The screen is displayed again when the doors or liftgate is unlocked.
Before Driving
Electric Vehicles
3-19
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

▼Convenient Functions
Timer Charging
Timer charging is a function which
charges the battery automatically
according to a preset time.
You can charge the battery using this
function during time periods when
electricity rates are low. In addition,
the maximum charge limit can be set
and changed.
For the setting method, refer to
Charging Settings on page 3-21.

Canceling the Charging Timer
You can cancel the charging timer
setting temporarily to start charging the
battery immediately.
For the setting method, refer to
Charging Settings on page 3-21.

Climate Control Timer
The climate control timer is a function
which operates the cooling or heating
system automatically according to a
preset time.
The power consumption of the air
conditioner after starting to drive the
vehicle is reduced by operating the air
conditioner and providing a
comfortable temperature in the cabin
before driving.
For the setting method, refer to Turning
On the Climate Control System Using
the Timer (Climate Control Timer) on
page 5-12.

Charge Connector Lock
The charge connector lock is a function
which locks the charging connector
connected to the vehicle so that it
cannot be pulled out.
You can also select the lock conditions
for the charging connector according
to locations and situations.
For the setting method, refer to
Charging Settings on page 3-21.
Locked When Connected
The charging connector is locked at
the same time the charging
connector is connected. The
charging connector is unlocked for 1
minute after the driver’s door is
unlocked.
Select Locked When Connected
when charging in the following
locations/situations.
Outdoor parking lotCharging using your charging cable
at a charging facility
Locked When Charging
The charging connector is locked
only while charging. The charging
connector is unlocked when the
charging is
finished. In addition, the
charging connector is unlocked for 1
minute after the driver’s door is
unlocked, even while charging.
Select Locked When Charging when
leaving the vehicle while charging at
a public charging station where
people are waiting to charge their
vehicles.
O ff
The charging connector is not
locked.
Select O ff when charging in the
following locations/situations.
Indoor parking lot with a shutter
Before Driving
Electric Vehicles
3-20
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07