2021 VOLKSWAGEN T-ROC trailer

Vehicles with a manual gearbox:

Pulled vehicle (rear)
Ensure that the ignition is switched on so that the steering wheel is not locked and so that you can
indicate, sound the horn and operate the wipers if necessary.
the
ignition is switched on and the vehicle is rolling. Otherwise you must press the brake pedal with
significantly more force and also use more effort for steering.

-rope is always taut.
ox in neutral or select the selector lever position N.
Fitting the rear towing eye

Fig. 178 On the right-hand side of the rear bumper: removing the cover.

Fig. 179 On the right-hand side of the rear bumper: screwed-in towing eye.
First read and observe the introductoryinformation and safety warnings⇒Introduction 
The towing eye must always be kept in the vehicle.
In vehicles with a factory-fitted towing bracket, there is no mounting for the screw-in towing eye
behind the cover. To tow, swivel out or fit and use the ball head ⇒ Trailer towing .

When the engine is working hard, the engine oil level should be kept within the upper permissible
area ⇒ Fig. 186  Ⓒ, for instance during extended motorway journeys in summer, when towing a
trailer ⇒ Trailer towing , or when climbing mountain passes.
Checking the engine oil level and refilling the engine oil

Fig. 186 Engine oil level markings on the oil dipstick (variants).

Fig. 187 In the engine compartment: engine oil filler cap (illustration).
First read and observe the introductoryinformation and safety warnings⇒Introduction 
Key to ⇒ Fig. 186 :
Engine oil level too high – observe the messages on the instrument cluster display or contact a
qualified workshop, if necessary.
Do not fill engine oil.
Engine oil level OK.
Engine oil level too low – fill engine oil.
Checklist
Carry out the steps in the specified order ⇒ :

temporary spare wheel should be exchanged for a normal wheel as soon as possible. The
temporary spare wheel is designed for a short period of use only.
-supplied wheel bolts.
ve using more than one spare wheel that differs from the normal tyres.
⇒ Tyre pressure .

ot fit a temporary spare wheel to the rear axle when towing a trailer ⇒  .
Tyre lettering and tyre type

Fig. 198 International tyre lettering.
First read and observe the introductoryinformation and safety warnings⇒Introduction 
⇒ Fig. 198  Tyre lettering
(example)
Meaning
① Product name Individual tyre designation of the manufacturer.
② DOT The tyre complies with the legal requirements of
the USA Department of Transportation,
responsible for tyre safety standards.
③ JHCO CHWS 2213 Tyre identification number (a) – may be only
on the inner side of the wheel) and date of

Manual gearbox: select a gear.

Ask all vehicle occupants to leave the vehicle and stand at a safe distance away from moving traffic.

Switch on the hazard warning lights and set up the warning triangle In an emergency. Observe any
legal requirements.

Chock the wheel diagonally opposite the wheel being worked on with a stone, collapsible chocks or
another suitable object.

When towing a trailer: unhitch the trailer from the vehicle and park it properly .

Remove any items of luggage from the luggage compartment.

Remove the spare wheel or temporary spare wheel and the vehicle toolkit from the luggage
compartment.

Remove the hubcaps Hubcaps.

WARNING
Ignoring any of the items on this important safety checklist can lead to accidents and severe injuries.

Wheel bolts

When towing a trailer : unhitch the trailer from the vehicle and park it properly.

Loosen the wheel bolts Wheel bolts.

Find the jacking point under the vehicle which is closest to the wheel that is being changed.

Insert the crank into the opening on the jack (depends on the vehicle equipment).

Crank up the jack until it just fits under the jacking point of the vehicle.

Ensure that the entire surface of the foot of the jack is resting securely on the floor, and that the
foot of the jack is positioned fully underneath the point of application and .

Position the jack and simultaneously continue to crank the claw up until it is in position around the
vertical rib underneath the vehicle .

Crank the jack further until the wheel is just clear of the ground.

WARNING
Incorrect use of the vehicle jack could cause the vehicle to slip off the jack. This could lead to severe
injuries. Observe the following points in order to reduce the risk of injuries:
jacks could slip out of position – this includes vehicle jacks supplied with other Volkswagen models.
the vehicle to slip off the jack. If necessary, use a large, sturdy board or similar support for the
vehicle jack.

side member securely ⇒ Fig. 206 .
lace any part of your body (e.g. an arm or leg) underneath the vehicle if the latter is
supported only by the vehicle jack.

The air compressor from the breakdown set may be operated from the 12-volt socket, even if the
power rating on the type plate of the air compressor exceeds the maximum power rating of the
socket.
Preparations
First read and observe the introductoryinformation and safety warnings⇒Introduction 
Checklist
Always carry out the following actions in the given order ⇒ :

If your vehicle has a flat tyre, park the vehicle on a firm and level surface at a safe distance from
moving traffic.

Switch on the electronic parking brake Parking and manoeuvring.

DSG® dual clutch gearbox: move the selector lever to position P DSG® dual clutch gearbox.

Switch off the engine and remove the key from the ignition.

Manual gearbox: select a gear Manual gearbox: selecting a gear.

Ask all vehicle occupants to leave the vehicle and stand at a safe distance away from moving traffic.

Switch on the hazard warning lights and set up the warning triangle In an emergency. Observe any
legal requirements.

Check whether the puncture can be repaired with the breakdown set The tyre sealant must not be
used:.

When towing a trailer: unhitch the trailer from the vehicle and park it properly .

Vehicles with two seats: there is no floor covering in the rear of the vehicle interior because there is
no rear bench seat ⇒ .
Vehicles with four seats: the centre seat on the rear bench seat cannot be used⇒ .
Transporting children safely
As with vehicles with passenger car approval (M1), approved child restraint systems can be used on
the seats ⇒ Safe transport of children .
Towing a trailer
If the vehicle is approved for towing a trailer, observe any local regulations for driving with a trailer
and using a towing bracket.
If the vehicle exceeds the gross vehicle weight rating or the rear axle load, do not exceed 80 km/h
when towing a trailer. This also applies to countries where higher speeds are permitted. Keep to
country-specific speed limits which may be lower for vehicles with trailers than for vehicles without
trailers.
The vehicle documents contain details of permitted excess loads. If no excess loads are shown, the
vehicle can be driven at 100 km/h, taking account of the laws which apply in different countries.
Technical data
Please refer to the vehicle documentation for technical data.

WARNING
Risk of injury and electric shock from exposed cables.
vehicle are covered up when using the vehicle.

WARNING
Risk of serious injuries due to transporting passengers incorrectly.

ms such as seat
belts and head restraints.

WARNING
Risk of serious and fatal injuries.

Fig. 214 Vehicle identification number.
Vehicle data sticker
The vehicle data sticker ⇒ Fig. 213  is located on the cover of the owner's manual and under the
rear luggage compartment trim on the luggage compartment wall. It contains the following data:
Vehicle identification number (chassis number)
Vehicle type, engine power, gearbox type
Engine and gearbox codes, paint number, interior equipment. In the example, the engine code
is CPTA ⇒ Fig. 213 .
Additional equipment, PR numbers
Type plate
The type plate ⇒ Fig. 213  can be seen on the lower part of the door pillar when the driver door is
open. Vehicles for certain export countries do not have a type plate.
The type plate contains the following data:
Approval
Gross vehicle weight rating
Gross combination weight rating (vehicle plus trailer)
Gross front axle weight rating
Gross rear axle weight rating
Vehicle identification number (VIN)
The vehicle identification number can be read from outside the vehicle through a viewer in the
windscreen ⇒ Fig. 214  (arrow). The viewer is located in the lower corner of the windscreen. The
vehicle identification number is also stamped on the right-hand water drainage channel. The water
drainage channel is located between the suspension turret and wing. Open the bonnet to gain
access to the vehicle identification number ⇒ In the engine compartment .
The vehicle identification number can be displayed in the Infotainment system using the button
and the and Service function buttons ⇒ Infotainment system controls and displays .
Vehicle data