2021 MERCEDES-BENZ V-CLASS MPV heating

#
Avoid high engine speeds and driving at
full thro ttle until the engine has reached
its operating temp erature. Note
s on short-distance trips
If th eve hicle is predominantly used in short-dis‐
ta nce driving, a fault in the automatic cleaning
function of the diesel particulate filter can occur.
Due tothis, fuel may also accumulate in the
engine oil and cause engine failure.
During automatic cleaning, extreme lyhot exhaust
ga ses escape from theex haust pipe. Maintain a
dis tance of at least 1 m to other objects, e.g.
par kedve hicles, in order toavoid material dam‐
age.
If yo u main lydrive short dis tances, you should
drive on a mo torw ay or go for a country drive for
20 minutes every500 km. This facilitates the
re ge neration of the diesel particulate filter.
Information about driving abroad
Service
An extensive Mercedes-Benz service is also avail‐
able abroad. Ne vertheless, please remember that
services or spare parts may not be available
immediatel y.The releva nt wo rkshop directories
are available from a Mercedes-Benz Service
Cent re.
Fu el
In some countries, only fuels with an inc reased
sulphur con tent are available.
Uns uitable fuel can cause engine damage. Yo u
can find fur ther information under "Fuel"
(/ page 270).
Ad Blue ®
Ad Blue ®
is not available in suf ficient quality in all
countries. Therefore, check theAd Blue ®
leve l,
particular lybefore driving outside Europe
(/ page 148). Consul t aqualified specialist
wo rkshop for advice.
Yo u can find information about AdBlue ®
in "Oper‐
ating fluids and capacities" (/ page271).
Low beam
In countries in whi chtraf fic drives on the oppo‐
site side of thero ad from the count ryin which
th eve hicle is regis tere d, you will ha vetoswitch
th e headlamps tosymmetrical dipped beam. This
will pr event oncoming traf fic from being dazzled.
Symm etrical dipped beam will no longer illumi‐
nate the edge of the car riag ewa y as far or as
high. Ve
hicles with halogen headlamps:
It is not necessa ryto change the headlamps over
to symmetrical dipped beam. The statutory
requ irements of the count ries in which tra ffic
drives on the opposite side of thero ad from the
country in whi ch theve hicle is regis tere d are also
met without changing over.
Ve hicles with LED headlamps:
Yo u can set the low beam for driving on theright
or left via the on-board computer (/ page189).
Information about transport byrail
Tr ansporting your vehicle byrail may be subject
to cer tain restrictions or requ ire special meas‐
ures tobe take n in some countries due tovarying
tunnel heights and loading standards.
Yo u can obtain information about this from a
Mercedes-Benz Service Cent re.
Information on brakes &
WARNING Risk of accident due tothe
brake sy stem overheating
If yo u lea veyour foot on the brake pedal
when driving, the brake sy stem may overheat.
This increases the braking dis tance and the
brake sy stem may evenfa il. #
Never use the brake pedal as a foot re st. #
Do not depress the brake pedal and the
accelerator pedal at the same time
while driving. *
NO
TECausing wearto the brake linings
by permanently depressing the brake
pedal #
Do not permanently depress the brake
pedal while driving. #
Touse braking ef fect of the engine, shift
to a lo werge ar in good time. Downhill
gradients
On long and steep downhill gradients you should
obse rveth efo llowing instructions:
R invehicles with an automatic transmission,
shift down toshift ranges 2or 1in good time
so that the engine is running at a medium to
high engine speed (/ page143).
R invehicles with a manual transmission, shift
down toa lo werge ar in good time, so that the
engine is running at a medium tohigh engine
speed. 13 8
Driving and pa rking

%
Chan
gethe shift range in good time when
cruise control or the limiter are activated.
Obser vethe driving tips (/ page137).
Yo uth ereby make use of the braking ef fect of the
engine and do not ha vetobrake as of tento main‐
tai nth e speed. This relie vesth e load on the
service brake and pr events the brakes from over‐
heating and wearing tooqu ickl y.
Heavy and light loads
If th e brakes ha vebeen subjected toa heavy
load, do not stop theve hicle immediatel y.Drive
on for a short while. The brakes cool down more
qu ickly in the air flow.
If th e brakes ha vebeen used only moderately,
yo u should occasionally test their ef fectiveness.
To do this, brake more firm ly from a higher speed
while pa ying attention tothe traf fic conditions.
The brakes will grip better as a result.
We tro ad sur faces
If yo u ha vebeen driving for a long time in heavy
ra in without braking, there may be a dela yed
re sponse when youfirs t apply the brakes. This
may also occur af ter driving thro ugh a car wash
or deep water.Yo u must depress the brake pedal
more firm ly. Maintain a grea ter dis tance tothe
ve hicle in front.
While paying attention tothe traf fic conditions,
yo u should brake theve hicle firm lyafte r driving
on a wetro ad sur face or thro ugh a car wash. This
heats the brake disks so that they dry more
qu ickl y,which pr otects them against cor rosion.
Limited braking ef fect on salt-treate dro ads:
R a layer of salt on the brake disks or brakepads
can increase braking dis tances considerably,
or braking may happen on only one side
R maintain an especially large safe dis tance to
th eve hicle in front
To remo vethe la yer of salt:
R apply the brakes from time totime, paying
attention totraf fic conditions
R carefully dep ress the brake pedal at the end
of a journey and af terth est art of a new jour‐
ney
Ne w brake dis ksand brakepads
New brakepads and brake disks only reach their
optimal braking ef fect af ter appro ximately
10 0 km.
Un tilthen, compensate forth ere duced braking
ef fect by applying greater pressure tothe brake
pedal. For saf etyre asons, Mercedes-Benz recom‐ mends
that you on lyha ve brakepads and brake
disks which are appr ovedby Mercedes-Benz
ins talled on your vehicle.
Other brake disks or brakepads may compromise
th e saf ety of your vehicle.
Alw aysre place all brake disks and brakepads on
an axle at the same time. Alw aysfit new brake‐
pads when replacing brake disks.
Information about driving on wetro ads
Note s on aquaplaning
Aq uaplaning can take place once a cer tain
am ount of water has accumulated on thero ad
sur face.
Obser vethefo llowing no tes during heavy precipi‐
ta tion or in conditions in which aquaplaning may
occu r:
R reduce your speed
R avoid tyre ruts
R avoid sudden steering mo vements
R brake carefully
Note s on driving through water on roads
If th e maximum permissible height of thewate r is
exc eeded when ford ing, theve hicle can be dam‐
aged.
Obser vethefo llowing if you must drive thro ugh
wate r:
R thewate r level of standing water may not be
abo vethe lo wer edge of the front bumper
R you may drive no fasterthan walking pace
R vehicles tr avelling in front, or oncoming vehi‐
cles, can create waves which may exceed the
maximum permissible height of thewa ter
The braking ef fect of the brakes is reduced af ter
fo rd ing. Brake carefully while paying attention to
th e traf fic conditions until braking po wer has
been fully restored.
Note s on driving in mountainous areas
Ve hicles with diesel engines: the operating
saf ety of the diesel engine is guaranteed up toan
ele vation of 2,500 m ab ovesea le vel.Yo u may
exc eed this ele vation for a short time, e.g. in
mountainous terrain. Do not drive continuously at
ele vations ab ove2,500 m. Otherwise, you may
damage the diesel engine.
When driving in mountainous areas, no tethat
engine output, and therefore start-off gradeabil‐
ity, will dec rease with inc reasing ele vation. The
ECO start/ stop function is no longer available Driving and parking
13 9

%
The drive program switches automatically
from
; toA (vehicles with drive pro‐
gram ;). All-wheel drive
Note
s onthe 4MATIC 4MATIC ensures permanent drive
for all four
wheels, and toge ther with ESP ®
it impr oves the
ve hicle's traction.
% In wintry
road conditions, the maximum
ef fect of 4MATIC can be achie ved only if you
use winter tyres (M+S tyres), with sn ow
ch ains if necessar y.
Use DSR (Downhill Speed Regulation) when driv‐
ing downhill off-road (/ page160).
If yo ufa ilto adapt your driving style, 4MATIC can
neither reduce therisk of an accident nor over‐
ri de the la wsof ph ysics. 4MATIC cannot take
account of road, weather and traf fic conditions.
4MATIC is only an aid. You are responsible espe‐
cially for maintaining a safe dis tance from the
ve hicle in front, forve hicle speed, for braking in
good time and forst ay ing in lane. AIRMATIC
Fu
nction of AIRMATIC AIRMATIC is an air suspension sy
stem with an all-
ro und le vel control sy stem, which also ensures
th e best possible suspension and cons tant
ground clearance, even wi tha laden vehicle.
When you drive at speed, theve hicle is lo wered
automatically toimpr ovedriving saf ety and to
re duce fuel consum ption. There is also the option
of raising theve hicle le vel while driving slowl y,
e.g. for driving off public roads. The AIRMATIC
settings are dependent on the drive program
selection.
AIRMATIC consists of thefo llowing functions and
components:
R all-round air suspension
R speed-dependent lo wering toreduce fuel con‐
sum ption
R high le velfo r greater ground clearance when
driving slowly; set with drive program Lift
F/¦, e.g. off public roads
R DYNA MIC SELECT switch
% Fo
rth e drive program Lift,the multifunction
display sho ws theF symbol next tothe transmission position displ
ay. The media dis‐
pl ay forth e multimedia sy stem sho wsthe
¦ symbol.
Ve hicle le vels per drive prog ram
Drive programs Aand¥:
R theve hicle is set tonormal le vel
R at speeds abo veappr ox.11 0 km/h, theve hi‐
cle is lo wered
R at speeds below appr ox.75 km/h, theve hicle
is raised again
Drive prog ram C:
R theve hicle is set tolow le vel
R at higher speeds, theve hicle le vel does not
continue tolower
Drive program F/¦:
R theve hicle is set tohigh le vel
R at speeds abo veappr ox. 30 km/h, theve hicle
le ve l lo wersto the normal le vel
R at speeds below appr ox.10 km/h, theve hicle
is raised again
R Atspeeds abo veappr ox.10 0 km/h, theve hi‐
cle switches todrive prog ram A.
% If
th eve hicle is raised in theLift drive pro‐
gram or lo wered when changing from theLift
drive program toano ther drive program,
occasional creaking noises may occur at the
brake.
% Operation with a trailer or bicycle
rack:if
th e electrical connection has been cor rectly
es tablished, theve hicle remains on normal
le ve lre ga rdless of speed.
Sy stem limits
AIRMATIC may not be available or ha veonly limi‐
te dav ailability in thefo llowing cases:
R The overheating pr otection has been activa‐
te d due tofrequent le velch anges within a
short time. The Compressor is cooling mes‐
sage is then shown in the multifunction dis‐
pla y. 14 6
Driving and pa rking

Af
terth e cooling phase, AIRMATIC is again
av ailable without restrictions. Re
fuelling Re
fuelling theve hicle &
WARNING Risk offire or explosion from
fuel
Fu els are highly flammable. #
Fire, naked flames, smoking and crea‐
tion of spar ksmust be avoided. #
Swit choff the ignition and, if available,
th est ationary heater, before and while
re fuelling theve hicle. &
WARNING Risk of injury from fuels
Fu els are poisonous and hazardous to your
health. #
Do not swallow fuel or let it come into
contact with skin,eyes or clo thing. #
Do not inhale fuel vapour. #
Keep children away from fuel. #
Keep doors and windo wsclosed du ring
th ere fuelling process.
If yo u or other people come into contact with
fuel, obser vethefo llowing: #
Immediately rinse fuel off your skin with
soap and water. #
If fuel comes into contact with your
ey es, immediately rinse them thor‐
oughly with clean water.Seek medical
attention immediately. #
Ifyo u swallow fuel, seek medical atten‐
tion immediatel y.Do not induce vomit‐
ing. #
Change immediately out of clo thing that
has come into con tact with fuel. &
WARNING Risk offire and explosion due
to electros tatic charge
Electros tatic charge can igni tefuel vapour. #
Before you open the fuel filler cap or
ta ke hold of the pump nozzle, touch the
me tallic vehicle body. #
Toavo id creating ano ther electros tatic
ch arge , do not getinto theve hicle again
during there fuelling process. &
WARNING Risk offire from fuel mixture
Ve hicles with a diesel engine:
If yo u mix diesel fuel with petrol, theflash
point of the fuel mixture is lo werth an that of
pure diesel fuel.
While the engine is running, component pa rts
in theex haust sy stem may overheat without
wa rning. #
Neverre fuel using petrol. #
Never mix petrol with diesel fuel. *
NO
TEDo not use diesel torefuel vehicles
with a petrol engine If
yo u ha veaccidentally refuelled with the
wrong fuel:
R do not swit ch the ignition on. Otherwise
fuel can enter the engine.
Even small amounts of the wrong fuel
could result in damage tothe fuel sy stem
and the engine. The repair costs are high. #
Consult a qualified specialist workshop. #
Have the fuel tank and fuel lines drained
comple tely. *
NO
TEDo not use petrol torefuel vehicles
with a diesel engine If
yo u ha veaccidentally refuelled with the
wrong fuel:
R do not swit ch the ignition on. Otherwise,
fuel can enter the fuel sy stem.
Even small amounts of the wrong fuel
could result in damage tothe fuel sy stem
and the engine. The repair costs are high. #
Consult a qualified specialist workshop. #
Have the fuel tank and fuel lines drained
comple tely. *
NO
TEDama getothe fuel sy stem caused
by ove rfilled fuel tanks #
Only fill th e fuel tank until the pump
nozzle switches off. Re
quirements
R The vehicle is unloc ked.
R The auxiliary heating is switched off. Driving and parking
147

Calling up
theAd Blue ®
ra nge and AdBlue ®
fill
le ve l display
On-board computer:
4 Service 5
AdBlue
Ad Blue ®
freezes at a temp erature of appr ox‐
imately -11 °C. The vehicle is equipped with an
Ad Blue ®
preheating sy stem at thefa ctor y.This
means that winter operation is also ensured for
te mp eratures below -11 °C. If youto p up AdBlue ®
at temp eratures below -11 °C, theAd Blue ®
level
in the instrument clus ter may not be displa yed
cor rectl y.Ifth eAd Blue ®
is frozen, drive for at
least 20 minutes and then park theve hicle for a
minimum of 30 seconds, so that the le vel is cor‐
re ctly displa yed. In extreme winter conditions,
th e time needed todetect the amount topped up
may be considerably longer. Park theve hicle in a
wa rm garage tospeed up this process. #
Call up the menu.
The multifunction display will show the
Ad Blue ®
leve l.
To pping up AdBlue ®
* NOTEEngine damage due toAd Blue ®
being in the fuel #
AdBlue ®
must not be used tofill th e fuel
ta nk. #
Only use AdBlue ®
to fill th eAd Blue ®
ta nk. #
Do not overfill theAd Blue ®
tank. *
NO
TEContamination of theve hicle inte‐
ri or due toAd Blue ®
lea kage #
Afterto pping up, carefully close the
Ad Blue ®
re fill conta iner. #
Avoid car rying AdBlue ®
re fill conta iners
permanently in theve hicle. *
NOTEOver filling theAd Blue ®
tank due to
th eve hicle standing at an angle The
AdBlue ®
tank can only be filled as inten‐
ded when theve hicle is par ked on a le vel sur‐
fa ce. This way,va riations in thefilling amount
are avoided.
When filling there ser voir when theve hicle is
st anding at an angle, there is a risk of overfill‐
ing. This may damage exhaust gas af tertre at‐
ment components. #
Park theve hicle on a le vel sur face tofill
th eAd Blue ®
tank. Re
quirements
R The auxiliary heating is switched off.
R The ignition is switched off.
R The front left-hand door is open.
The following messages that appear in succes‐
sion in the multifunction display indicate that you
need torefill th eAd Blue ®
tank:
R Refill AdBlue See Owner's Manual
The AdBlue ®
tank has dropped tothere ser ve
le ve l.
R Refill AdBlue Emer. oper. in XXX km See Own-
er's Manual
The low AdBlue ®
leve l will result in limited
per form ance af terth ere maining dis tance dis‐
pl ay ed has been driven. Top up AdBlue ®
as
qu ickly as possible.
R Emergency operation: 20 km/h No start in
XXX km See Operating Instructions
The vehicle speed is limited toappr oximately
20 km/h. You will on lybe able todrive the
ve hicle the dis tance shown. Subsequently, it
will no longer be possible tostart the engine.
R Refill AdBlue Engine start not possible
The vehicle can no longer be star ted.
Yo u can also ha vetheAd Blue ®
fill le vel and the
Ad Blue ®
ra nge displ ayed (/ page149).
Opening theAd Blue ®
filler cap #
Open the front door on the left-hand side and
fo ld out filler flap 1. #
Close all vehicle doors topreve nt ammonia
va pours from entering theve hicle interior. #
Turn blue AdBlue ®
filler cap 2anti-clockwise
and remo veit.
Fu elfiller cap 3forth e fuel remains closed. Driving and parking
14 9

#
Toactivate/deactivate: pressthe0076 but‐
to n.
The di stance warning function and the auton‐
omous braking function of Active Brake Assi st
are deactivated or activated.
When the functions are deactivated, the00D4
symbol appears in the Assis tance graphic in
th e multifunction displa y.
The next time theve hicle is star ted, Ac tive Brake
Assi stis automatically activated. Fu
nction of Adaptive Brake Lights Ad
aptive brake lights warnfollowing traf fic in an
emergency braking situation with th efo llowing
signals:
R Byflashing the brake lamps
R By activating the hazard warning lights
If th eve hicle is braked sharply from speeds
abo ve50 km/h, the brake lamps flash rapidl y.
This pr ovides traf fic tr ave lling behind you with an
eve n more noticeable warning.
If th eve hicle is tr avelling at speeds of more than
70 km/h at the beginning of the brake applica‐
tion, the hazard warning lights switch on once the
ve hicle is stationar y.When pulling away again,
th e hazard warning lights switch off automatically
at appr oximately 10km/h.
Yo u can also swit choff the hazard warning lights
using the hazard warning button (/ page107). Cruise control and limiter
Fu
nction of cruise control
Cruise cont rol accelerates and brakes theve hicle
automatically in order tomaintain a pr eviously
st ored speed.
If yo u accelerate toove rtake, forex ample, the
st ored speed is not dele ted. If youre mo veyour
fo ot from the accelerator pedal af terove rtaking,
cruise control will resume speed regulation back
to thestored speed.
Yo u operate cruise control using the cruise con‐
trol le ver.Yo u can store any speed abo ve
30 km/h.
Obser vethe no tes on driving sy stems and your
re sponsibility; you may otherwise failto recog‐
nise dangers (/ page 153). Sy
stem limits
Cruise control may be unable tomaintain the
st ored speed on uphill gradients. The stored
speed is resumed if the uphill gradient evens out
and theve hicle's speed does not fall below
30 km/h.
On long and steep downhill gradients, you should
ch ange down toa lo werge ar in good time. Take
particular no teofthis when driving a laden vehi‐
cle. By doing so, you will make use of the
engine's braking ef fect. This will take some of the
st ra in off the brake sy stem and pr eventthe
brakes from overheating and wearing tooqu ickl y.
If yo uch ange wheel size on your vehicle, check it
is assigned tothe cor rect wheel size catego ry
( / page 258). If the category is changed without
re coding the cont rol units in theve hicle, the func‐
tioning of cruise cont rol may be impaired.
Do not use cruise control in thefo llowing situa‐
tions:
R in traf fic situations whe refrequent speed
ch anges are required, e.g. in heavy traf fic or
on winding roads
R off-road or on con stru ction sites
R on slippe ryor slick roads, as the drive wheels
can lose traction when accelerating and the
ve hicle can then skid
R ifth ere is poor visibility
Fu nction of the limiter
The limiter restricts the speed of theve hicle. To
adjust tothe set speed quickl y,the limiter applies
th e brakes automaticall y.
Yo u can limit the speed as follo ws:
R Variable: for speed restrictions, e.g. in built-
up areas.
R Perm anen t:for long-term speed restrictions,
e.g. when driving in winter tyre mode.
Yo u can operate theva riable limiter with the
cruise control le ver.Yo u can store any speed
abo ve30 km/h. You can also per form settings
while theve hicle is stationary if theve hicle has
been star ted.
Obser vethe no tes on driving sy stems and your
re sponsibility; you may otherwise failto recog‐
nise dangers (/ page 153).
If yo uch ange wheel size on your vehicle, check it
is assigned tothe cor rect wheel size catego ry
( / page 258). If the category is changed without
re coding the cont rol units in theve hicle, the func‐
tioning of the limiter may be impaired. 15 8
Driving and pa rking

Example: engine oil
filler opening #
Obser vethe information rega rding appr oved
engine oil under "Operating fluids and capaci‐
ties" (/ page273). #
Unscr ewand remo vethe cap 1. #
Top up engine oil. #
Fitthe cap 1onthefiller opening and
tigh ten.
When doing so, make su rethat the cap
engages cor rectly. #
If present, check the oil le vel using the oil dip‐
st ick (/ page 223). #
Inthe case of vehicles without an oil dipstic k,
ch eck the oil le vel with the on-board com‐
puter af terth e next journey (/ page 222).
It is necessary torunth e engine for an extended
pe riod af ter each oil top up tocor rectly de tect
th e oil le vel. Fill le velch anges during oil top ups
may not be immediately visible. Depending on the
driving profile, the new oil le vel can only be dis‐
pla yed af ter a driving time of up to60 minutes.
If necessa ry, only top up thequ antity of oil shown
in the instrument clus ter display and check the
oil le vel again af terth e next journe y. Checking/topping up
the coolant &
WARNING Risk offire ‑ and inju ryfrom
antifreeze
If antifreeze comes into contact with hot com‐
ponent parts in the engine compartment, it
may ignite. #
Allow the engine tocool down before
yo uto p up the antifreeze. #
Make sure that no antifreeze spills out
next tothefiller opening. #
Thoroughly clean the antifreeze from
component parts before starting the
ve hicle. &
WARNING Risk of scalding from hot
coolant
If yo u open the cap, you could be scalded. #
Letthe mo tor cool down before opening
th e cap. #
When opening the cap, wear pr otective
gl ove s and saf etygl asses. #
Open the cap slowly torelease pres‐
sure. Only
check and top up the coolant le vel when the
ve hicle is stationary on a le vel sur face and the
engine has cooled down. The coolant temp era‐
ture must be below 50°C. &
WARNING Risk of burn s from hot com‐
ponent parts in the engine compartment
Cer tain component pa rts in the engine com‐
partment can be very hot, e.g. the engine, the
cooler and pa rts of theex haust sy stem. #
Allow the engine tocool down and only
to uch component parts desc ribed in the
fo llowing. Coolant con
tains glyc ol and is therefore poison‐
ous. #
Obser vethe information under "Operating flu‐
ids and capacities" (/ page274).
* NO
TEPaint wo rkdamage due tocoolant If coolant
gets on painted sur faces, the paint‐
wo rkcan be damaged. #
Add coolant carefully. #
Remo vespilled coolant. Re
gular lych eck the engine cooling sy stem and
th e heating sy stem for leaks . Ifthere is a loss of
coolant, ha vethe cause de term ined and rectified
in a qualified specialist workshop without dela y. Maintenance and care
225

Yo
u must obse rveth e no tes and mixing ratios
indica ted on theta nk.
Note s on fuel quality forve hicles with diesel
engines
Gene ral no tes
Obser vethe no tes on operating fluids
(/ page 269). &
WARNING Risk offire from fuel mixture
If yo u mix diesel fuel with petrol, theflash
point of the fuel mixture is lo werth an that of
pure diesel fuel. #
Neverre fuel using petrol in diesel
engines. #
Never mix petrol with diesel fuel. *
NO
TEDama gedue toincor rect fuel Even small amounts of
the wrong fuel could
re sult in damage tothe fuel sy stem, the
engine and the emission cont rol sy stem. #
Only refuel using sulphur- free diesel fuel
th at con form sto European standard
EN 590, or an equivalent specification.
In countries without sulphur-fre e diesel
fuel, refuel using only lo w-sulphur diesel
fuel with a sulphur content less than
50 ppm.
Ne verre fuel with one of thefo llowing fuels:
R Petrol
R Marine diesel
R Heating oil
R Pure fatty acid me thyl es ter (bio-diesel) or
ve get able oil
R Paraffin or kerosene
If yo u ha veaccidentally refuelled with the
wrong fuel: #
Do not swit ch the ignition on. #
Consult a qualified specialist workshop. *
NO
TEMalfunction due tocontaminated
fuel Impuri
ties in the fuel can lead tomalfunctions
of the fuel sy stem. #
Ifyo u are using drums or canis ters to
re fuel theve hicle, you should filter the
fuel before filling. In acco
rdance with the European standard
EN 1694 2,you will find the compatibility mar ks
fo r fuel in thefo llowing places:
R Ontheve hicle on the information label in the
fuel filler flap
R Throughout Europe on the fuel dispenser or
pump nozzles suitable foryo ur vehicle 1
For diesel fuel with a maximum of 7% byvol‐
ume bio-diesel (fatty acid me thyl es ter) 2
For paraf finic diesel fuel
XTL-co mpatible vehicles
Alternatively, you can also refuel with paraf finic
diesel fuel (e.g. HVO=hyd roge nated vege table oil,
GT L=Gas- To-Liquid) that complies with the Euro‐
pean standard EN 1594 0. Paraffinic diesel fuels
are collectively know n as XTL.
% Re
fuel with paraf finic diesel fuels to
EN 1594 0 only if the appropriate compati‐
bility ma rkis present in your fuel filler
flap.
B10- fatty acid meth ylester
Mercedes-Benz appr oves the use of B10 fatty
acid me thyl es ter (lo w-sulphur diesel fuel with a
maximum of up to10%by vo lume fatty acid
me thyl es ter) for all vehicles with Euro 5 diesel
engines with Common Rail Direct Injector (CDI).
Yo u may on lyrefuel with the appr ovedfatty acid
me thyl es ter if thefa tty acid me thyl es ter propor‐
tion conforms tothe ASTM D6 751St andard. It
must also ha vetherequ iredoxidation stability of
at least 6 h, in accordance with the EN 1411 2 Te
ch nical da ta271