2021 Lexus GX460 Owner's Manual / LEXUS 2021 GX460 OWNER'S MANUAL QUICK GUIDE (OM60T24U)

25
GX460_QG_OM60T24U_(U)
■Selecting constant speed control mode
With the cruise control off, press and
hold the “ON/OFF” button for 1.5 sec-
onds or more.
Immediately after the “ON/OFF”
button is pressed, the radar cruise
control indicator will come on. After-
wards, it switches to the cruise con-
trol indicator.
Switching to constant speed control
mode is only possib le when operating
the lever with the cruise control off.
Accelerate or dece lerate, with accel-
erator pedal operation, to the desired
vehicle speed (at or above approxi-
mately 25 mph [40 km/h]) and push
the lever down to set the speed. Cruise control “SET” indicator will
come on.
The vehicle speed at the moment the
lever is released becomes the set
speed.1
2

26
GX460_QG_OM60T24U_(U)
LDA (Lane Departure Alert)
■Turning LDA system on
Press the LDA switch to turn the LDA sys-
tem on.
The LDA indicator illuminates.
Press the LDA switch again to turn the
LDA system off.
When the LDA system is turned on or
off, operation of the LDA system con-
tinues in the same condition the next
time the engine is started.
When driving on roads with white (yellow) lines, this function alerts the driver when the
vehicle might depart from its lane.
The LDA system recognizes visible white (yellow) lines with the camera sensor on the
upper portion of the front windshield.

27
GX460_QG_OM60T24U_(U)
Intuitive Parking Assist (if equipped)
■Turning the intuitive parking assist on/off
Press or of the meter control switches and select on the multi-informa-
tion display.
Press or of the meter control swit ches and select , and then press .
Each pressing of the switch turns the intuitive pa rking assist on and off.
When ON is selected, Intuitive parking assist indicator will come on.
Multi-terrain Select (if equipped)
Multi-information display
The selected Multi-terrain Select
mode will be displayed on the multi-
information display.
Multi-terrain Select mode selector
switch
Multi-terrain Select indicator
The distance from your vehicle to nearby obstacles when parallel parking or maneuver-
ing into a garage is measured by the sensors and communicated via the multi-informa-
tion display, the multimedia screen (if equipped), the navigation system screen (if
equipped), and a buzzer. Always check the surrounding area when using this system.
1
2
Multi-terrain Select is a system that helps drivability in off-road situations.
1
2
3

28
GX460_QG_OM60T24U_(U)
■Selectable modes
When the Crawl Control is turned off
A mode which matches the road conditions
can be selected from among the following 5
modes.
: MUD & SAND mode
Suitable for muddy roads, sandy roads,
snow-covered roads, dirt trails and
other slippery or dirty conditions. The
MUD&SAND mode indicator
illuminates on the multi-information
display.
: LOOSE & ROCK mode
Suitable for slippery conditions
consisting of mixtures of earth and
loose rock. The LOOSE & ROCK
mode indicator illuminates on the
multi-information display.
: MOGUL mode
Suitable for very bumpy road
conditions, such as mogul roads.
MOGUL mode indicator illuminates
on the multi-information display.
: ROCK & DIRT mode
Suitable for very bumpy road
conditions, such as mogul or rocky
roads. ROCK &DIRT mode indicator
illuminates on the multi-information
display.
: ROCK mode
Suitable for rocky roads. ROCK mode
indicator illuminates on the multi-
information display.
When the Crawl Control is turned on
: MTS AUTO mode
The most suitable mode is automatically se lected according to the selected Crawl Con-
trol mode. MTS AUTO indicator illumina tes on the multi-information display.
1
2
3
4
5

29
GX460_QG_OM60T24U_(U)
Multi-terrain Monitor (if equipped)
VIEW switch
Display
The Multi-terrain Monitor helps the driver to check the vehicle surroundings. It assists in
determining the conditions around the driver in a variety of situations, such as when judging
conditions during off-road driving or checking for obstacles when parking.
1
2
The surroundings area displayed can be switched by pressing the VIEW switch.

30
GX460_QG_OM60T24U_(U)
Four-wheel Drive System
■Four-wheel drive control switch
H4 (high speed position)
Normal driving on all types of roads.
L4 (low speed position)
Driving requiring maximum power and
traction such as climbing or descend-
ing steep hills, off- road driving, and
hard pulling in sand or mud, etc. The low speed four-wheel drive indi-
cator will come on.
■ Center differential lock/unlock switch
Lock the center differential when your vehi-
cle’s wheels get stuck in a ditch or when
driving on a slippery or bumpy surface.
The center differential lock indicator will
come on.
Unlock the center differential after the
wheels have been freed, or after moving
to a flat, non-slippery surface.
To unlock the center differential, push
the switch again.
Use the four-wheel drive control switch and center differential lock/unlock switch to select
the following transfer and center differential modes.
1
2

31
GX460_QG_OM60T24U_(U)
Crawl Control (if equipped)
Crawl Control ON/OFF switch
The indicator light on the switch comes
on when operating.
Crawl Control speed selector switch
Crawl Control indicators
The Crawl Control indicator is lit and
the slip indicator flashes when operat-
ing.
Multi-information display
The selected multi-terrain select mode
will be displayed on the multi-informa-
tion display.
Allows travel on extremely ro ugh off-road surfaces at a fixed low speed without pressing
the accelerator or brake pedal. Minimizes loss of traction or vehicle slip when driving on
slippery road surfaces, hel ping for stable driving.
1
2
3
4

32
GX460_QG_OM60T24U_(U)
BSM (Blind Spot Monitor) (if equipped)
The Blind Spot Monitor is a system that has 2 functions;
● The Blind Spot Monitor function
Assists the driver in making th e decision when changing lanes
● The Rear Cross Traffic Alert function
Assists the driver when backing up
These functions use same sensors.
The Blind Spot Monitor on/off screen and indicator
The Blind Spot Monitor system can be turned on/off on the multi-information display.
When the system is set to on, the indica tor illuminates in the meter and the buzzer
sounds. The Blind Spot Monitor function and the Rear Cross Traffic Alert function are
turned on/off simultaneously.
Outside rear view mirror indicator
The Blind Spot Monitor function:
When a vehicle is detected in the blind spot, the outside rear view mirror indicator
comes on while the turn signal lever is not operated. If the turn signal lever is operated
toward the detected side, the outsid e rear view mirror indicator flashes.
The Rear Cross Traffic Alert function:
When a vehicle approaching from the right or left rear of the vehicle is detected, the
outside rear view mi rror indicators flash.
Monitor screen display (The Rear Cross Traffic Alert function only)
If a vehicle approaching from the right or left at the rear of the vehicle is detected, the
Rear Cross Traffic Alert icon for the detect ed side will be displayed on the monitor
screen.
This illustration shows an example of a vehicle approaching from the left at the rear of
the vehicle.
The Rear Cross Traffic Alert buzzer (The Rear Cross Traffic Alert function only)
When a vehicle approaching from the right or left rear of the vehicle is detected, a
buzzer sounds from behind the rear seat.
1
2
3
4