2021 HYUNDAI I20 Owners Manual

4-32
Safety system
OAI3039016OAI3039016
The ISOFIX anchorages symbols are
located on the left and right rear seat
cushions to identify the position of the
ISOFIX anchorages in your vehicle (see
arrows in illustration).
OAI3039017OAI3039017
Both rear outboard seats are equipped
with a pair of ISOFIX anchorages as well
as a corresponding top-tether anchorage
on the back side of the rear seats.
(Child Restraint Systems with universal
approval according to ECE-R44 or
ECE-R129 need to be fixed additionally
with a top-tether connected to the
corresponding top-tether anchorage
point on the back side of the rear seats.)
ISOFIX anchorages are located between
the seatback and the seat cushion of the
rear seat left and right outboard seating
positions.
Securing a Child Restraint System
with the “ISOFIX system”
To install a ISOFIX-compatible Child
Restraint System in either of the rear
outboard seating positions:
1. Move the seat belt buckle away from
the ISOFIX anchorages.
2. Move any other objects away from
the anchors that could prevent a
secure connection between the Child
Restraint System and the ISOFIX
anchorages.
3. Place the Child Restraint System on
the vehicle seat, then attach the seat
to the ISOFIX anchorages according to
the instructions provided by the Child
Restraint System manufacturer.
4. Follow the instructions of the Child
Restraint System’s manufacturer for
proper installation and connection
of the ISOFIX attachments on the
Child Restraint System to the ISOFIX
anchorages.
WARNING
Take the following precautions when
using the ISOFIX system:
• Read and follow all installation
instructions provided with your Child
Restraint System.
• To prevent the child from reaching
and taking hold of unretracted
seat belts, buckle all unused rear
seat belts and retract the seat belt
webbing behind the child. Children
can be strangled if a shoulder belt
becomes wrapped around their neck
and the seat belt tightens.

4-33
04
• NEVER attach more than one
Child Restraint System to a single
anchorage. This could cause the
anchor or attachment to come loose
or break.
• Always have the ISOFIX system
inspected by your dealer after an
accident. An accident can damage
the ISOFIX system and may not
properly secure the Child Restraint
System.
Securing a Child Restraint System
with “Top-tether anchorage”
system (if equipped)
OBI3030004OBI3030004
First, secure the Child Restraint System
with the ISOFIX anchorages or the
seat belt. If the Child Restraint System
manufacturer recommends the top-
tether to be attached, attach and
tighten the top-tether to the top-tether
anchorage. Top-tether anchorages are
located on the back of the rear seats.
WARNING
Take the following precautions when
installing the top-tether:
• Read and follow all installation
instructions provided with your Child
Restraint System.
• NEVER attach more than one Child
Restraint System to a single top-
tether anchorage. This could cause
the anchorage or attachment to
come loose or break.
• Do not attach the top-tether to
anything other than the correct top-
tether anchorage. It may not work
properly if attached to something
else.
• Child Restraint System anchorages
are designed to withstand only those
loads imposed by correctly fitted
Child Restraint Systems. Under no
circumstances are they to be used for
adult seat belts or harnesses or for
attaching other items or equipment
to the vehicle.

4-34
Safety system
OAI3039018OAI3039018
To install the top-tether :
1. Route the Child Restraint System
top-tether over the Child Restraint
System seatback. Route the top-tether
under the headrest and between the
headrest posts, or route the top-tether
over the top of the vehicle seatback.
Make sure the strap is not twisted.
2. Connect the top-tether to the top-
tether anchorage, then tighten
the top-tether according to the
instructions of your Child Restraint
System’s manufacturer to firmly
attach the Child Restraint System to
the seat.
3. Check that the Child Restraint System
is securely attached to the seat by
pushing and pulling the seat forward
and from side-to-side.
Installing a child restraint system by
lap/shoulder belt
E2MS103005E2MS103005
To install a child restraint system on the
outboard or center rear seats, do the
following:
1. Place the child restraint system in
the seat and route the lap/shoulder
belt around or through the restraint,
following the restraint manufacturer’s
instructions. Be sure the seat belt
webbing is not twisted.
E2BLD310E2BLD310
2. Fasten the lap/shoulder belt latch
into the buckle. Listen for the distinct
“Click” sound.
Position the release button so that it is
easy to access in case of an emergency.

4-35
04
MMSA3030MMSA3030
3. Buckle the seat belt and allow the
seat belt to take up any slack. After
installation of the child restraint
system, try to move it in all directions
to be sure the child restraint system is
securely installed.
If you need to tighten the belt, pull more
webbing toward the retractor. When you
unbuckle the seat belt and allow it to
retract, the retractor will automatically
revert back to its normal seated
passenger emergency locking usage
condition.

4-36
Safety system
Child Seat Restraint for Vehicle ISOFIX PositionsUse child safety seats that have been officially approved and are appropriate for your children. When using the child safety
seats, refer to the following table..
Mass GroupSeating Position
Front PassengerSecond Row
Outboard LeftCenter
(2 POINT BELT)Outboard Right
Group 0
(0-9months)up to 10kg X U X U
Group 0+
(0-2years)up to 13kg X U X U
Group I
(9months-4years)9 to 18kg X U UF U
Group II
(15 to 25kg)15 to 25kg X U UF U
Group III
(22 to 36kg)22 to 36kgD X U UF U
U = Suitable for “universal” category Child Restraints Systems approved for use in this mass group.
UF = Suitable for forward facing “universal” category restraints for use in this mass group.
X = Seat position not suitable for children in this mass group.

Remarks:- Co driver seat:
Up right, Rearmost position & Seat belt shoulder anchorage to lowest position.

4-37
04
$,5%$*

4-38
Safety system
WARNING
• Even in vehicles with air bags, you
and your passengers must always
wear the safety belts provided
in order to minimize the risk and
severity of injury in the event of a
collision or rollover.
• SRS and pretensioners contain
explosive chemicals.
If scraping a vehicle without
removing SRS and pretensioners
from a vehicle, it may cause fire.
Before scraping a vehicle, we
recommend that you contact an
authorized Hyundai dealer.
• Keep the SRS parts and wirings away
from water or any liquid. If the SRS
components are inoperative due to
exposure to water or liquids, it may
cause fire or severe injury.
How does the air bag system
operate
• Air bags are activated (able to inflate
if necessary) only when the ignition
switch is placed to the ON or START
position.
• Air bags inflate instantly in the event
of serious frontal or side collision in
order to help protect the occupants
from serious physical injury.
• There is no single speed at which the
air bags will inflate.
Generally, air bags are designed to
inflate based upon the severity of a
collision and its direction. These two
factors determine whether the sensors
produce an electronic deployment/
inflation signal.
• Air bag deployment depends on a
number of factors including vehicle
speed, angles of impact and the
density and stiffness of the vehicles or
objects which your vehicle hits in the
collision. The determining, factors are
not limited to those mentioned above.
• The front air bags will completely
inflate and deflate in an instant.
It is virtually impossible for you to see
the air bags inflate during an accident.
It is much more likely that you
will simply see the deflated air
bags hanging out of their storage
compartments after the collision.

4-39
04
• In order to help provide protection
in a severe collision, the air bags
must inflate rapidly. The speed of
air bag inflation is a consequence
of extremely short time in which a
collision occurs and the need to get
the air bag between the occupant
and the vehicle structures before the
occupant impacts those structures.
This speed of inflation reduces the risk
of serious or life-threatening injuries
in a severe collision and is thus a
necessary part of air bag design.
However, air bag inflation can also
cause injuries which can include facial
abrasions, bruises and broken bones
because the inflation speed also
causes the air bags to expand with a
great deal of force.
• There are even circumstances under
which contact with the steering
wheel air bag can cause fatal
injuries, especially if the occupant is
positioned excessively close to the
steering wheel. WARNING
• To avoid severe personal injury or
death caused by deploying air bags
in a collision, the driver should sit as
far back from the steering wheel air
bag as possible. The front passenger
should always move their seat as far
back as possible and sit back in their
seat.
• Air bag inflates instantly in an event
of a collision, passengers may be
injured by the air bag expansion force
if they are not in a proper position.
• Air bag inflation may cause injuries
including facial or bodily abrasions,
injuries from broken glasses or burns.