2021 AUDI Q2 ignition

Driving

CO

< o rN
iv
rN
i—i

00
Releasing the selector lever manually (left-
hand drive vehicles)
Applies to: vehicles with automatic gearbox

The
selector lever can be released manually if
the electrical power supply should
fail.

K

Fig.
80 Selector lever: Removing the boot

Fig.
81 Manually releasing the selector lever from position
P
This section describes how to manually release
the selector Lever on Left-hand drive vehicles.
The selector lever must be manually released
from position
P
in order to move or tow the
vehi­

cle.

The manual release mechanism is Located on the
right underneath the selector gate. Releasing the
selector lever requires a certain degree of practi­
cal
skill.
We therefore advise you to obtain pro­
fessional assistance.
To release the selector lever, you
wilL
need the
screwdriver from the vehicle's tool kit, which is
located in the luggage compartment

^>page
319. Use the flat-blade side of the rever­
sible screwdriver insert.
Removing the selector lever boot
• Apply the parking brake
& ^/^
to prevent
your vehicle from moving. If this is not possi­

ble,
use other means to prevent your vehicle
from moving.

•
Switch off the ignition.
• To loosen the selector lever boot, carefully in­
sert the flat-blade side of the screwdriver into
the opening
at
the side of the boot
^>Fig.
80.

•
Carefully lever off the boot with the screwdriver

and,
at the same time, pull the boot upwards
-arrow- at the crease with your hand until it is
released at all four corners.

•
Fold the boot over the selector lever knob

=>
Fig.
81.
Releasing the selector lever manually

•
Insert the screwdriver in the opening for the
yellow release lever
^>Fig.
81.

•
Using the screwdriver, carefully pull the release
lever towards the rear as far as it will go and
hold it in this position.

•
Now press the interlock button on the selector
lever
®
and move the selector lever to position
N.

•
After manually releasing the selector lever
make sure you clip the gear lever boot back into
the gearshift gate.
A WARNING
- Only use the manual release mechanism
when the vehicle is on level ground or a
slight gradient.
- The selector lever must not be moved out of
position
P
if the parking brake is not ap­

plied.
If this does not work, use the brake
pedal to hold the vehicle or use wheel
chocks or similar to block one of the front
and rear wheels. If
you
do not apply the

brake,
the vehicle may roll away and cause
an accident.
93

Driving
Releasing the selector lever manually
(right-hand drive vehicles)
Applies to: vehicles with automatic gearbox

The
selector lever can be released manually if
the electrical power supply should
fail.

n

Fig.
82 Selector lever: Removing the boot

m

i

Fig.
83 Manually releasing the selector lever from position
P
This section describes how to manually release
the selector lever on right-hand drive vehicles.
The selector lever must be manually released
from position
P
in order to move or tow the
vehi­

cle.

The manual release mechanism is located on the
right underneath the selector gate. Releasing the
selector lever requires a certain degree of practi­
cal
skill.
We therefore advise you to obtain pro­
fessional assistance.
To release the selector lever, you will need the
screwdriver from the vehicle's tool kit, which is
located in the luggage compartment

^>page
319. Use the flat-blade side of the rever­
sible screwdriver insert.
Removing the selector lever boot

•
Apply the parking brake fâ)
o^
to prevent
your vehicLe from moving. If this is not possi­

ble,
use other means to prevent your vehicle
from moving.

•
Switch off the ignition.
• To Loosen the selector lever boot, carefully in­
sert the flat-blade side of the screwdriver into
the opening
at
the side of the boot
^>Fig.
82.

*•
Carefully lever off the
boot
with the screwdriver

and,
at the same time, pull the boot upwards
-arrow- at the crease with your hand until it is
released at
alL
four corners.

•
Fold the boot over the selector lever knob

^Fig.
83.

•
Take out the panel for the selector Lever
posi­

tion indicator and Let it hang down to one side,
suspended by the cable
0 •=>
Fig.
83.
Releasing the selector lever manually

•
Insert the screwdriver in the opening for the
yellow release lever (section
@
of
<$
Fig.
83).

•
Using the screwdriver, carefully pull the release
lever towards the rear as far as it will go and
hold it in this position.

•
Now press the interlock button on the selector
lever
@
and move the selector Lever to position
N.

•
After manually releasing the selector lever,
make sure you fit the panel for the selector lev­
er position indicator back in the selector gate
and clip the selector lever boot back into place.
A WARNING
- Only use the manual release mechanism
when the vehicle is on level ground or a
slight gradient.
94

Towing a trailer
Tyre pressure
Check the tyre pressures on your car, and adjust
for "full
load"
conditions (refer to the sticker list­
ing the tyre pressures)
^>page
307. It may also
be necessary to adjust the tyre pressures on the
trailer according to the recommendations of the
trailer manufacturer.
Exterior mirrors
Check whether you can see enough of the road
behind the trailer with the standard mirrors. If
this is not the case you should have additional
mirrors fitted. Both exterior mirrors should be
mounted on hinged extension brackets. Adjust
the mirrors to give sufficient vision to the rear.
Headlights
Before starting
a
journey, check the headlight
beam settings with the trailer hitched up. Adjust
the headlight settings if necessary.
On vehicles with halogen headlights, the
head­

light range control must be adjusted, see

tapage
49.
The headlight range control will be adjusted au­
tomatically if your vehicle is equipped with LED
headlights*.
Power supply
To ensure that the engine can be started again
after the ignition is switched off, the power
man­

agement system
^>page
149 controls the distri­
bution of electrical power and gradually switches
off unnecessary electrical equipment. The trailer
is supplied with power during this period. The
power supply to the trailer is interrupted while
the engine is being started.
Removable ball joint coupling
Vehicles with a factory-fitted towing bracket are
equipped with a removable
ball
joint coupling.
This is stored in the spare wheel well or in a sepa­
rate bag on the floor of the luggage compart­
ment, together with the necessary fitting instruc­

tions.

We recommend having the car serviced be­
tween the normal inspection intervals if it
used frequently for towing a trailer.
Trailer stabilisation system
Applies to: vehicles with towing bracket
Trailer stabilisation helps to reduce the risk of
the vehicle skidding when towing a
trailer.

When is the trailer stabilisation
system1'

activated?
Trailer stabilisation is active when the following
requirements are met:
- The ESC must be switched on
^>page
146 and
fully functional (no ESC malfunction).
- The trailer connector must be properly secured
in the vehicle socket.
- The vehicle speed must be higher than approx.
60 km/h.
How trailer stabilisation works
In many cases, the driver can stabilise a swaying
trailer by manually braking the vehicle.
However, if the ESC detects that the trailer is
swaying and this is affecting the towing vehicle,
it will automatically brake the vehicle in order to
stabilise the trailer. The indicator
Lamp Hi
will
flash in the instrument cluster. If possible, do
not turn the steering wheel at this stage.
In order to warn traffic behind you, the brake
lights will come on during this automatic braking

operation.

A trailer may sway quite considerably without the
trailer stabilisation system intervening.
If the system for activating the trailer brake
lights is defective, this will be indicated in the in­
strument cluster display
opage
35,
:&
Bulb

monitor.
•

CO

rN
rN
t-H
o <
x)
Not available on vehicles for some markets.
97

Driver assist systems

CO

< o rN
iv
rN
•-i

00
sections, please temporarily switch off the
cruise control system.
- Make sure you do not unintentionally rest
your foot on the accelerator - this will over­
ride the cruise control system which, as a re­
sult, will not brake the vehicLe.
-The automatic braking function may be de­
activated if
a
system fault occurs in the
brake system (e.g. if the brakes overheat)
while the cruise control system is activated.
All the other cruise control functions remain
activated as long as the indicator lamp
^
is
lit.
Before driving down a
long,
steep gradient, it
is advisable to reduce speed and select a low­
er gear. In this way you will make use of the
engine braking effect and relieve the Load on
the brakes.
© Note
- Applies to vehicles with manual gearbox:
The set speed cannot be reached if the cur­
rently selected gear is too high or too low or
if the engine would
overrevorfailto
run
smoothly at the target speed. Make sure to
change up or down a gear in good time.
- The brake lights come on when the system
brakes the vehicle.
Setting a new speed
Applies to: vehicles with cruise control system
• Briefly push the Lever towards
©/®

^>page
104, Fig. 94 to increase or reduce the
cruising speed in small steps.

•
To increase or reduce the speed quickly, hold
the lever towards
©/®
until you reach the de­
sired cruising speed.
Overriding the set speed
Applies to: vehicles with cruise control system
You can use the accelerator pedal to increase
speed in the normal way, for example to overtake
another vehicle. Once you release the accelera­
tor, the system will revert to the speed you stor­
ed initially.
However, if the vehicLe exceeds the programmed
speed significantly for
a
long time, the cruise
control system will be deactivated temporarily.
The indicator lamp
El
in the instrument cluster
will go out, but the programmed speed will re­
main stored.

Pre-selecting
a speed
Applies to: vehicles with cruise control system

You
can preselect a desired speed while the ve­
hicle is stationary.

•
Switch on the ignition.

•
Pull the lever to position
® ^>page
104,
Fig. 94.
• Press the lever up towards © or down towards

0
in order to increase or reduce the cruising
speed setting.
This function allows you to enter the desired
cruise control setting speed ahead of
time,
for
example before joining a motorway.
Once
you are
on the motorway, you can activate the cruise
con­

trol system by pulling the lever to position ®.
Switching off
Applies to: vehicles with cruise control system
Switching off temporarily

•
Press the brake pedal, or

•
Push the lever to position @ (click stop not en­
gaged)
^>page
104, Fig. 94, or
Switching off completely

*•
Push the lever to position
©
(click stop engag­

ed),
or

•
Switch off the ignition.
The speed setting will remain stored after the
system is temporarily deactivated. To resume the
programmed cruising speed, release the brake
pedal and pull the lever to position ®.
The stored speed will be deleted once the
igni­

tion is switched off. •
105

Driver assist systems

CO

<
O
rN
iv
rN
t-H
o < 00

•
Press button ® to store the cut-off speed while
the car is moving.
The instrument cluster display will indicate the
stored cut-off
speed,
and the indicator lamp
Q

will light up.
Applies to: vehicles with cruise control system or Audi adap­
tive cruise control
While the speed Limiter is switched on, you can
switch to the cruise control
^>page
104 or adap­
tive cruise control
^>page 111
systems. Press
button
®1)
until the corresponding system is
displayed in the instrument cluster.
The last cut-off speed set for the speed limiter
remains stored and can be applied again when
you switch back into speed limiter mode.
Changing the cut-off speed
Applies to: vehicles with speed limiter

•
Briefly push the Lever towards ©/©

^>page
106, Fig. 96 to increase or reduce the
cut-off speed in small steps.

•
To increase or reduce the cut-off speed in
big­

ger steps, hold the lever towards ©/© until
you reach the desired cruising speed.
Overriding the cut-off speed
Applies to: vehicles with speed limiter
To override the speed limiter temporarily, press
the accelerator fully past the point of resistance
(kick-down feature).
Speed limiting is suspended temporarily. The in­
dicator lamp
QB
flashes while the system is deac­

tivated;
the cut-off speed setting will remain

stored.
The system is reactivated automatically
as soon as your speed drops below the original
stored setting.
Switching off
Applies to: vehicles with speed limiter
Switching off temporarily

•
Push the lever towards © (click stop not en­
gaged)
^>page
106, Fig. 96. The instrument
cluster display will indicate the stored cut-off

speed,
and the indicator
lamp^will
light up.
Switching off completely

•
Push the lever to position © (click stop engag­

ed),
or

•
Switch off the ignition.
The cut-off speed setting will remain stored after
the system is temporarily deactivated. To resume
the programmed cut-off
speed,
pull
the lever to
position ©. The vehicle speed is limited to the
stored cut-off setting as soon as your current
driving speed drops below the stored cut-off

speed.

The stored cut-off speed will be deleted once the
ignition is switched off.
Automatic deactivation

QQ
Speed limiter: currently unavailable. See
owner's manual
The speed Limiter has been automatically deacti­
vated because the system has detected a fault
which could impair its function. Try switching on
the speed limiter again Later.
A WARNING
The speed limiter may be deactivated if a
fault occurs in the brake system (e.g. if the
brakes overheat) while the speed limiter is ac­

tivated.

©
Not

If
a
system fault requires the speed limiter to
switch off automatically, for safety reasons it
does not switch off completely until the driver
releases the accelerator pedal once or deacti­
vates the system manually.

l)
On some equipment versions, the speed limiter is not
available and button
(S)
has no function.
107

Driver assist systems
key in use. If you change to a different type
of trailer, you may need to change the maxi­
mum trailer speed setting.
- Information is also provided in the head-up
display*.
- Please note
that
the navigation system (SD

card)*
is immediately no longer available if
the SD card is removed from the SD card
reader.
Driver messages
Applies to: vehicles with camera-based traffic sign
recogni

tion

EJ
Traffic sign recognition: currently unavaila­

ble.
No camera view
This message will appear if the camera view is
obstructed
^>page
108. The system will switch
it­

self off.

EJ
Traffic sign recognition: currently restricted
This message appears, for instance, in the event
of a navigation system fault. The Limited func­
tionality may cause fewer speed limits to be dis­
played (which increases the possibility of an er­

ror).

Traffic sign based speed warning: currently
unavailable. See owner's manual
No warning will be given if the selected warning
threshold is exceeded.
Traffic sign recognition: system fault
The function of the system is impaired; the sys­
tem will be deactivated. Drive to a qualified
workshop soon.
No traffic sign recognised
No relevant navigation data are available, and no
speed limit has been detected.
Traffic sign recognition: outside operational
area
Function unavailable in this country
The vehicLe is being driven in a country outside
the system's operational area.
Rest recommendation
General notes
Applies to: vehicles with rest recommendation
Under certain conditions, the system can detect
that the driver needs to take a break.
At the beginning of a trip, the system monitors
the driver's general steering style. Using this as a
reference, the system continuously compares the
current steering input at speeds of between 60
km/h and 200 km/h. If the evaluation of the
steering input implies a lapse in the driver's
con­

centration,
the system will then recommend a
break
^>page
111,
Instrument cluster display.
The rest recommendation function is designed
for journeys on motorways and major roads.
System limitations
The rest recommendation function may misinter­
pret the steering input in certain driving situa­

tions,
such as the following:
- On twisty roads.
- On rough roads.
- In poor weather.
- During performance driving.
- When the driver's attention is distracted.
Resetting the system
The system is automatically reset if
you...

- switch off the ignition.
- release the driver's seat belt and open the driv­
er's door.
- drive slower than 60 km/h for a while. If you
subsequently increase your speed again, the
system will reevaluate the driving style.

/\
WARNING
- Never drive when you are
tired.
As a driver
you are always responsible for ensuring that
you
are
fit to drive.
- On
Long
journeys, make sure to take
quate breaks at regular intervals.

ade-

- The system cannot always tell if
you
need a
break.
110

Driver assist systems

CO

< o rN
iv
rN
•-i

00
- In certain situations, the system may misin­
terpret driving manoeuvres and inappropri­
ately recommend a break.
- No acute warning is given if the driver falls
into a microsleep.
Instrument cluster display
Applies to: vehicles with rest recommendation

H
Rest recommended
If the warning lamp lights up and the message
appears, the evaluation of the steering input has
resulted in a rest recommendation. This is also
indicated by a warning tone. Take a break as soon
as possible.
The message may be displayed again once if nec­
essary.
Switching on/off
Applies to: vehicles with rest recommendation
Select the following on the infotainment system:

|MENU|
button > Car > left control button > Driv­
er assist > Rest recommendation.
© Note
If you switch off the system,
it
will remain
switched off the next time you switch on the

ignition.

Audi adaptive cruise
control
Description
Applies to: vehicles with Audi adaptive cruise control

»

Fig.
100 Sensor range
The adaptive cruise control is a combined speed
and distance control system. It assists the driver
by controlling the road speed and the distance to
the vehicle in front within certain limits imposed
by the system. The adaptive cruise control sys­
tem can accelerate and brake when it detects a
vehicle in front. This provides maximum comfort
both on long motorway journeys and in conges­
ted traffic (automatic gearbox*).
What can the adaptive cruise control do?
The adaptive cruise control uses a radar. The ra­
dar is subject to certain system limitations

opage
112.
When there is no traffic in front, the adaptive
cruise control works just like a normal cruise
con­

trol system by maintaining a constant speed.
When you draw closer to a vehicLe in front which
is detected by the system, the adaptive cruise
control matches your speed to that vehicle by au­
tomatically applying the brakes, and then main­
tains a constant distance (which you can adjust in
the settings). As soon as it detects no more
vehicles in front, the adaptive cruise control ac­
celerates back up to the cruising speed.
Applies to: vehicles with automatic gearbox
In congested traffic, the adaptive cruise control
can brake down to a standstill and accelerate
again (subject to general system limitations) un­
der certain conditions
*$page
115, Driving in
congested traffic. The traffic jam assist (active
lane assist)* can assist the driver in traffic jams
and heavy congestion
<=>page
117.
Which functions can the driver control?
When you switch on the adaptive cruise control,
you can set your current speed as the "cruising

speed"
^>page
113, Switching
on/off.

While you are driving, you can interrupt the
cruise control
opage
115 or change the speed
setting
Opage
114 at any time.
In addition, you can adjust the distance to
vehicles in front and the driving program for the
adaptive cruise control
^>page
116.

Ill

Driver assist systems
Setting the speed and activating the cruise
control

•
To set the current speed as the cruising speed
and activate the cruise control, press the
|SET|

button
<=>Fig.
104
"=>^.
The speed setting is in­
dicated by the LEDs © in the speedometer and
is also shown briefly in the system status
indi­

cator©
OF/g.
J
05.

•
Vehicles with automatic gearbox: To activate
the cruise control when the vehicle is station­
ary, the hold assist* function must have been
activated
or
you must press the brake pedal.
Switching off the adaptive cruise control

•
Push the Lever away from you to position © un­
til it engages. The message
ACC:
off will ap­
pear.
The LEDs indicating the stored speed in the
speedometer dial will go out.
(3) Warning and indicator lamps

I
- The adaptive cruise control is switched on.
No vehicle has been detected in front. A constant
cruising speed is being maintained.
] - A vehicle in front has been detected. The
adaptive cruise control is regulating the speed to
maintain a constant distance to the vehicle in
front, and will accelerate and brake the vehicle
automatically.

I
- Automatic gearbox: The adaptive cruise
con­

trol is switched on. A vehicle in front has been de­

tected.
Your vehicLe is stationary and will not be
set in motion again automatically.

I
- The adaptive cruise control alone is not able
to brake the vehicle sufficiently to maintain a
safe distance to the vehicLe in front. You must in­
tervene
ipage
117,
Driver intervention prompt.

©
Graphical display in instrument cluster
If the adaptive cruise control is not shown on the
instrument cluster display, you can call up the
display using the controls on the multi-function
steering wheel
^>page
15.
The graphical display shows you when a vehicLe in
front is detected and indicates how far away you
are from that vehicle:
No vehicle - No vehicLe has been detected in
front.
Vehicle in silver - A vehicle has been detected in
front.
Vehicle in red - Driver intervention prompt

<5page
117.

The five distance bars on the scale © represent
the distance setting (for information on how to
change the distance setting, refer to

^>page
116). The distance bars are coloured in
red from the bottom up if the actual distance is
shorter than the distance selected.

A
WARNING
Applies to: vehicles with automatic gearbox
If
you
press the
|SET|
button at
a
speed of less
than 30 km/h, the vehicLe will automatically
accelerate up to the minimum speed setting
of 30 km/h.
Note
- The speed setting is cleared for safety rea­
sons when you switch off the ignition or the
adaptive cruise control system.
- Applies to vehicles with front-wheel drive:
The electronic stabilisation control (ESC)
and traction control system (ASR) are auto­
matically activated when the adaptive cruise
control is switched on.
Setting a new speed
Applies to: vehicles with Audi adaptive cruise control

Fig.
106 Control lever: Setting a new speed

•
Briefly push the lever towards ©/© to in­
crease or reduce the cruising speed in small

steps.
•
114