2021 AUDI Q2 ignition

Lights and vision
© CAUTIO © CAUTION
- In icy conditions, check that the wiper
blades are not frozen to the windscreen. If
the wiper blades are frozen to the
wind­

screen when you switch on the windscreen
wipers, this could damage the wiper blades.
- Make sure you switch off the windscreen
wiper system (lever in position
@)
before
you use an automatic car wash. This will
avoid inadvertent triggering of the wipers
and possible damage to the wiper system.
© Note
- The windscreen wipers are deactivated
when the ignition is switched off. You can
activate the windscreen wipers after switch­
ing the ignition on again by moving the
windscreen wiper lever to any position.
- Worn or dirty wiper blades can cause smear­
ing on the glass. This can also impair the ef­
fectiveness of the rain sensor. Please check
the wiper blades regularly.
-The windscreen washer jets are heated*
when the ignition is switched on if the out­
side temperature is low.
- If
you
stop briefly, e.g. at traffic lights, the
wiper speed setting will automatically be re­
duced
by
one level.
Cleaning the wiper blades
Clean the wiper blades if the wipers leave smear­
ing on the glass. Use a soft cloth and glass clean­
ing solution.
Windscreen wipers
• Set the wiper arms to the service position

^>page
56.
• Lift the wiper arms away from the glass.
Rear window wiper
• Lift the rear wiper arm away from the glass.

/\
WARNING
Dirty wiper blades can impair the driver's view
- risk of accident!
If the wipers still Leave smearing on the glass
after they have been cleaned, the wiper
blades should be replaced
<=>page
56.
Changing the windscreen wiper blades

Fig.
47 Removing the wiper blades
Service position / wiper change position
• To move the windscreen wipers into the service

position,
switch off the ignition and move the
windscreen wiper lever to position (3) for at
least 2 seconds
<^page
55, Fig. 45.
• To move the windscreen wipers back to their
original position, switch on the ignition and
move the windscreen wiper lever to position (4)
for at least 2 seconds.
Taking off the wiper blade
• Lift the wiper arm away from the glass.
• Press the release button
(T)
on the wiper blade

^>Fig.
47. Keep hold of the wiper blade while
doing so.
• Take off the wiper blade in the direction of the
arrow.
Fitting the wiper blade
• Fit the new wiper blade into the mounting on
the wiper arm (5). You should hear it engage in
the wiper arm.
• Fold the wiper arm back down onto the
wind­

screen.

• Switch off the service position again.

A
WARNING
For safety, the wiper blades should be
changed once or twice a year.
56

Seats and storage
The ashtray is inserted in the centre console and
can be placed on either the driver's or front pas­
senger's side. Lift the lid to open the ashtray. Al­
ways put the ashtray safely back into the holder
after removing it (e.g. after emptying it).
A WARNING
Never put waste paper in the ashtray, as this
could cause a fire
Cigarette lighter
Applies to: vehicles with cigarette lighter

-

c
cc

o

Fig.
54 Centre console: Cigarette lighter
• Press in the cigarette lighter.
• When the cigarette lighter springs out, pull it
out completely.
The cigarette lighter should only be used as a
power source in exceptional circumstances, e.g.
for the compressor of the tyre repair kit.
A WARNING
The cigarette lighter only works when the ig­
nition is on. Improper use can cause serious
injury or start a fire. To avoid the risk of injury,
never leave children unsupervised in the
vehi­

cle with the key.
60
Power sources

-
CO

-

Fig.
55
12
Volt socket and USB inputs
When the ignition is switched on
or
the engine is

running,
the following electrical power sources
for external devices are available (depending on
the equipment fitted in your vehicle):
12 Volt sockets
®

Electrical equipment can be connected to the
12 Volt sockets. The appliances connected must
not exceed a power rating of 120 W.
The 12 Volt sockets are located in the front
cen­

tre console*, in the rear* and in the luggage com­
partment side
trim*.

USB inputs (2)
You can charge your mobile devices and/or
con­

nect them to the Audi music interface using the
USB inputs:
-
4*
Audi music interface* in the centre armrest
and at the front of the centre console. Or:
- CHARGE ONLY: USB charging socket* in the
centre armrest.
- CHARGE ONLY: Two USB charging sockets* on
the centre console in the rear.
For more information on the USB inputs, please
refer to
^>page
240, Multimedia connections.
Audi phone box
The Audi phone box* is located in the centre
con­

sole beneath the armrest. You can use it to
charge your mobile phone
<$page
177.

A
i
WARNING
Improper use can cause serious injury or start
a fire. To avoid the risk of injury, never Leave

Heating and cooling

cS5
Air recirculation mode
In air recirculation mode, the air from the interi­
or of the vehicle is filtered and recirculated. This
setting prevents fumes etc. from entering the in­
terior. We recommend switching on the air recir­
culation mode when driving through a tunnel or
in traffic queues
•=>
A-
The air recirculation mode is switched off when
the control is in the defrost position

Qjp
Rear window heating
If the rear window heating is activated with the
ignition switched on, the battery management
determines whether or not the vehicle battery
charge level is sufficient for the rear window
heating to be switched on. Otherwise the rear
window heating operates when the engine is
run­

ning,
and switches off automatically after about
10 - 20 minutes, depending on the outside
tem­

perature.
To switch on the rear window heating perma­
nently, press and hold the
CÛJD
button for at least
2 seconds. This setting will be stored for approxi­
mately 15 minutes after the ignition is switched

off.

J
Seat heating*
When you press the
«0
button, the seat heating is
switched on at level 3 (the highest level). The
LEDs indicate the temperature level. To reduce
the temperature, press the button again. To
switch off the seat heating, press the button re­
peatedly until all the LEDs have gone out.
The seat heating automatically switches from
level 3 to level 2 after about 10 minutes.
(7) CAUTION
To avoid damaging the heating elements of
the seat heating, please do not kneel on the
seat or apply sharp pressure at
a
single
point

© Note
- The setting for the driver's seat heating is
assigned to the key in use.
- If the front passenger's seat heating was on
when you Last switched off the ignition, it
will be switched on automatically only if the
ignition is switched on again within 10 mi­

nutes.

/K
WARNING
- For reasons of safety you should not Leave
the air recirculation switched on for too

long.
This mode prevents fresh air from en­
tering the vehicle, so the windows can mist
over if the air cooling* is switched off. Bad
visibility can cause an accident.
- People with limited capacity to feel pain or
sense temperature could burn themselves
when using the seat heating. These people
must not use the seat heating - risk of in­
jury!
68

Heating and cooling

%
Blower
You can adjust the blower speed manually using
the control
%.
You should leave the blower on at
a low setting to prevent the windows from mist­
ing up and to ensure that the vehicle interior is
constantly ventilated. Press the AUTO button for
automatic control of the blower speed.

%£/
%8/
'J Air distribution and air outlets
The buttons can be used to adjust the air distri­

bution.
Press the AUTO button for automatic air
distribution.
The round air outlets in the dashboard can be ad­
justed
^>page
71.
To prevent the front side windows from misting
up in wet weather, it's a good idea to open the
side air outlets and point them to the side.

Foot-Level
air outlets are provided underneath
the front seats to heat the rear cabin.

1
Defroster
The windscreen and side windows are defrosted
or demisted as quickly as possible. The air output
is increased to maximum and most of the air
comes out of the outlets below the windscreen.
The air recirculation mode is deactivated. The
temperature should be set to 22 °C or higher.
The temperature is regulated automatically. At
setting
$&
the A/C cooling mode is automatically
activated depending on the ambient tempera­

ture.

The defroster is switched off when the AUTO but­
ton is pressed.

<^>
Air recirculation mode
The air recirculation mode can be switched on
manually or automatically*.
- To switch the manual air recirculation mode
on/off, press the

button.
-The automatic* air recirculation function must
be activated on the infotainment system. Se­
lect the following on the infotainment system:

|MENU|
button > Car > left control button > A/C
> Auto recirculation. The air quality sensor,
which is designed for the detection of diesel
and petrol exhaust fumes, automatically
switches the air recirculation mode on or off
depending on the
level
of pollution in the out­
side air.
In air recirculation mode, the air from the interi­
or of the vehicle is filtered and recirculated. This
setting prevents fumes etc. from entering the in­
terior. We recommend switching on the air recir­
culation mode when driving through a tunnel or
in traffic queues
•=>
A-
The air recirculation mode is switched off when
the
<^>
or AUTO or
M.
button is pressed.
If the engine is
cold,
the air conditioner will auto­
matically switch to air recirculation mode when
the vehicle is reversing.

$tr
Rear window heating
If the rear window heating is activated with the
ignition switched on, the battery management
determines whether or not the battery charge
level is sufficient for the rear window heating to
be switched on. Otherwise the rear window heat­
ing operates when the engine is running, and
switches off automatically after about
10 - 20 minutes, depending on the outside
tem­

perature.
To switch on the rear window heating perma­
nently, press and hold the
S
button for at least
2 seconds. This setting will be stored for approxi­
mately 15 minutes after the ignition is switched

off.

^
Seat heating*
When you press the
«r
button, the seat heating is
switched on at level 3 (the highest level). The
LEDs indicate the temperature level. To reduce
the temperature, press the button again. To
switch off the seat heating, press the button re­
peatedly until all the LEDs have gone out.
The seat heating automatically switches from
level 3 to level 2 after about 10 minutes.
A WARNING
For reasons of safety you should not leave
the air recirculation switched on for too

long.
This mode prevents fresh air from en­
tering the vehicle, so the windows can mist
70