2021 AUDI Q2 engine

Checking and topping up fluids
Preparations
Applies to: vehicles with selective catalytic reduction

CO

<
O
rN
iv
rN
i—i

00

Fig.
241 Vehicle as seen from the rear right: Unscrewing
the AdBlue cap
The AdBlue filler neck is located immediately be­
side the diesel filler neck. Add at least the
amount of AdBlue displayed in the instrument
cluster. If
you
do not refill this amount of
fluid,

the system may not detect that the tank has
been refilled and it may not be possible to restart
the engine. You can refill with a maximum of 12

litres.

Important: A message in the instrument cluster
display informs you if
you
need to refill AdBlue.

•
Park the vehicle on a level surface.

•
Switch off the ignition.
• Open the tank flap
<^>page
290.

•
Unscrew the cap on the filler neck
anti-clock­

wise
^>Fig.
241.

*•
Refill AdBlue from a filler nozzle
^>page
293,
canister
^>page
294 or bottle
^>page
294.
A WARNING
AdBlue can cause irritation to the
skin,
eyes,
and respiratory organs. Wash thoroughly with
clean water should you come into contact
with this
fluid.
Seek medical assistance if nee­

ded.

© CAUTION
- Use only
AdBLue
that complies with the ISO
22241-1 standard. Do not mix AdBlue with
additives and do not dilute it with water.
- AdBlue must not be added to the diesel
tank, and diesel must not be added to the
AdBlue tank. Never start the engine if you
fill up with the wrong type of
fuel,
as this
could damage the tank system and the en­

gine.
Obtain professional assistance.
-AdBlue attacks surfaces such as paintwork,
plastic veneer and carpets. Remove spilt
flu­

id as soon as possible with a damp cloth and
plenty of water. If the AdBlue has already

solidified,
use warm water and a sponge.
Residues of AdBlue solidify after
a
while if
they are not removed and can damage the
affected surface.
- Do not keep refill bottles or canisters in the
vehicle, as AdBlue can leak and damage the
vehicle interior.
- Keep AdBlue away from clothing. Wash
thoroughly with clean water should you
come into contact with this
fluid.

\J
Note
Please follow the AdBlue manufacturer's in­
structions for storage and use.
Refilling AdBlue from a filler nozzle
Applies to: vehicles with selective catalytic reduction

•
Open the tank flap
^>page
290.

*•
Unscrew the cap on the filler neck
anti-clock­

wise
^>page
293, Fig. 241.

*•
Fill up with AdBlue until the first time the filler
nozzle cuts off the supply
•=>(]}.

•
Put the tank cap back on
opage
294, After re­
filling.
CAUTION
- The handle of the filler nozzle must point
downwards when filling the tank. Otherwise
the filler nozzle will not cut off the supply
automatically
^0
in Preparations on
page 293.
- You should stop refilling the first time the
filler nozzle automatically cuts off the sup­
ply. Otherwise the level of AdBlue in the
tank may be too high and AdBlue could
overflow
<=>©
in Preparations on page 293.
293

Checking and topping up fluids
Refilling AdBlue from a canister
Applies to: vehicles with selective catalytic reduction

#

Fig.
242 Canister with screw-on hose
• Take the cap off the refill canister
o^/n
Prep­
arations on page 293,
<=>(T)
in Preparations on
page 293.

•
Screw the end of the hose (î) clockwise onto
the opening on the canister®.

•
Remove the cap
@
from the other end of the
hose®.

•
Fit the end of the hose (2) onto the filler neck
on the vehicle and turn clockwise as far as the
stop to secure.
• Lift the canister and then tilt it. Keep it tilted
until empty or until no more fluid runs into the
tank.

•
Remove the canister and screw the tank cap
back on
^>page
294, After refilling.
CAUTIO
Use only refill canisters of the correct type ap­
proved for your vehicle. AdBlue may Leak out
if
you
use another system.
© Note
- Your qualified workshop can tell you which
refill canisters are approved
for
your
vehi­

cle.

- Approved refill canisters contain about 5 li­
tres of AdBlue.
Refilling AdBlue from a bottle
Applies to: vehicles with selective catalytic reduction

•
Take the cap off the refill bottle
<=>^
in Prepa­
rations on page 293,
•=>(?)
in Preparations on
page 293.

•
Screw the bottle clockwise onto the filler neck
as far as it will go.

•
To empty the bottle, lightly press the bottom
of the bottle. Keep pressing the bottom of the
bottle until the bottle is empty, or until no
more fluid runs into the tank.

•
Remove the bottle and screw the tank cap back
on
<=>page
294, After refilling.
(J) CAUTION
Use only refill bottles of the correct type ap­
proved for your vehicle. AdBlue may leak out
if
you
use another system.
- Refill bottles are available from qualified
workshops.
- Approved refill bottles contain about 1.9 Li­
tres of AdBlue.
After refilling
Applies to: vehicles with selective catalytic reduction
Closing the filler neck

•
Screw the AdBlue cap clockwise onto the filler
neck until the AdBlue cap clicks audibly
•=> /\
in
Preparations on page 293,
^>(T)in
Prepara­
tions on page 293.

•
Press the left side of the flap to close it (you
should hear it click into place).
After refilling
The vehicle must be driven so that the system
can detect the AdBlue which has been added.
This process can take several minutes.
• If the AdBlue tank had run dry and a range of
0 km was shown on the display, switch on the
ignition for approx. 30 seconds before starting
the engine.
© Note
AdBlue can freeze in the tank at very Low
tem­

peratures. In this case, the system will not
detect AdBlue when you refill and will contin­
ue to indicate a Low
AdBLue
Level. The mes­
sage will disappear as soon as the tank has

thawed.

294

Checking and topping up fluids

CO

rN
IV
rN
•-i

00
Emission controL
systems
Catalytic converter
Applies to: vehicles with petrol engine
The vehicle must only be used with unleaded pet­

rol,
otherwise the catalytic converter will be ir­
reparably damaged.
Never allow the fuel tank to run completely dry,
as the irregular supply of fuel can cause misfir­

ing.
This allows unburnt fuel to enter the exhaust

system,
which can cause overheating and dam­
age to the catalytic converter.
Diesel particulate filter
Applies to: vehicles with diesel engine
The diesel particulate filter can filter out almost
all soot particles contained in the exhaust gas. In
normal driving conditions the filter is self-clean­

ing.
Should the self-cleaning function of the filter
not be able to operate, e.g. when the vehicle is
continuously used only for short trips, the filter
becomes obstructed with soot and the indicator

lampnf°r
the
diesel particulate filter Lights up

cépage
34.
A WARNING
The exhaust system is very hot when the
vehi­

cle is being driven and after the engine has
been switched off.
- Never touch the tailpipes when they are hot
- risk of burns!
- Because of the high temperatures which can
occur in the emission controL system, do not
park the vehicle where the exhaust can
come into contact with flammable materials
under the car (e.g. on grass or at the forest
edge) - risk of fire!
- Do not apply any underseal agents in the
area around the exhaust system - risk of

fire!

Engine compartment
Working on components in the engine
compartment
Extra caution is necessary when working on com­
ponents in the engine compartment.
Always be aware of the danger of injury and
scalding as well as the risk of accident or fire
when working in the engine compartment (e.g.
when checking and refilling fluids). Always ob­
serve the warnings listed below and follow all
normal safety precautions. The engine compart­
ment of any motor vehicle is a potentially haz­
ardous area
oA-

A WARNING
- Switch off the engine.
-Switch off the ignition.

-Applythe
parking brake.
- On vehicles with manual gearbox place the
gear lever in neutral, on vehicles with auto­
matic gearbox move the selector lever to
position P.
- To avoid the risk of being scalded, never
open the bonnet if
you
see steam or coolant
escaping from the engine compartment.
Wait until no steam or coolant can be seen
before opening the bonnet.
- Wait for the engine to cool down.
- Keep children away from engine compart­
ment.
- Never spill fluids on a hot engine. These
flu­

ids can cause a fire (e.g. radiator
anti­

freeze).
- Take care not to cause short circuits in the
electrical system.
- When working in the engine compartment
be aware that the radiator fan may start
running suddenly, even if the ignition is
switched off - risk of injury!
- Do not unscrew the cap on the expansion
tank when the engine is hot. The cooling
system is under pressure.
- Protect face, hands and arms by covering
the cap with a large, thick rag to protect
against escaping coolant and steam.
295

Checking and topping up fluids
- Never remove the engine cover panel - risk
of burns!
- If any tests have to be performed with the
engine running, there is an extra safety risk
from the rotating parts, such as the drive

belts,
alternator and radiator
fan,
etc., and
from the high-voltage ignition system.
- Never touch the radiator fan. The electric
additional fan is controlled by temperature
and can start running without warning.
- Applies to vehicles with automatic gearbox:
Never open the throttle inadvertently (for
instance by hand from the engine compart­
ment) if
a
gear is engaged while the vehicle
is stationary with the engine running. The
vehicle will otherwise start moving immedi­
ately and could cause an accident.
- Observe the following additional warnings if
work on the fuel system or the electrical
system is necessary:
- Do not smoke.
- Never work near naked flames.
- Always keep an approved fire extinguisher
immediately available.
- Any work on the batteries and electrical sys­
tem in your vehicle entails a risk of injury
and chemical burns in addition to danger of
accident or fire.
For
this reason, you must
have the work carried out by
a
qualified
workshop.
© CAUTION
When topping up fluids make sure the correct
fluid is put into the correct filler opening. This
can otherwise cause serious malfunctions or
engine damage.
® For the sake of the environment
Inspect the ground underneath your vehicle
regularly so that any Leaks are detected at an
early stage. If
you
find spots of oil or other

fluids,
have your vehicle inspected in the
workshop.
© Note
located on the other side of the engine com­
partment.
Opening/closing the bonnet

The
bonnet is released from inside the vehicle.

Fig.
243 Detail of footwell on driver's side: Release lever

I

On right-hand drive vehicles* some of the
containers / reservoirs mentioned below are

Fig.
244 Unlocked bonnet: Lever
The wiper arms should be resting on the
wind­

screen:
make sure they are not in a raised
posi­

tion.
Otherwise the paint may get damaged.
Opening the bonnet

•
With the driver's door open, pull the lever un­
der the dashboard in the direction indicated
(arrow)
^>Fig.
243.

*•
Lift the bonnet slightly
•=> A-
•
Press the Lever under the bonnet in the direc­
tion indicated by the arrow
^>Fig.
244. This will
release the arrester hooks.

•
Open the bonnet.
Closing the bonnet
• To close the bonnet, pull it down to overcome
the spring pressure.

•
Then let it drop into the catches; do not press
down
|=>^.
•
296

Checking and topping up fluids
A WARNING
- To avoid the risk of being scalded, never
open the bonnet if
you
see steam or coolant
escaping from the engine compartment.
Wait until no steam or coolant can be seen
before opening the bonnet.
- For safety reasons the bonnet must always
be completely closed when the vehicle is

moving.
After closing it always check that it
is properly secured. It should not be possi­
ble to
lift
the front edges of the bonnet.
Should you notice that the bonnet is not
safely secured when the vehicle is moving,
stop the vehicle immediately and close the
bonnet properly, otherwise it could cause an
accident.
Engine compartment layout
Main components for checking and refilling

CO

< o rN
iv
rN
t-H
o <

?

Fig.
245 Typical locations of fluid containers, engine oil dipstick and engine
oilfiller
cap

(T)
Coolant expansion tank
C=t)
<^page
300
(2) Engine oil dipstick
Opage
298
(3) Engine
oilfiller
cap
(*&*)
Opage
298
(4) Brake fluid reservoir (CO))
^>page
301
(5) Vehicle battery (+) beneath a cover

^page
303,
^page
326
(?) Earth
point
on
body
(-)•=>page
303,

^>page
326
(7) Windscreen
washer
container
(<3?)
^>page
303

(§)
Fuse box
^page
332
The positions of the oil
dipstick
(2) and the en­
gine
oilfiller
cap(D^F/'g.
245 may be different
on some engine versions.
Engine oil
Choosing the correct engine oil grade
The service interval display in the instrument
cluster of your vehicle will inform you when it is
time for an oil change. We recommend having
the oil changed by
a
qualified workshop. •
297

Checking and topping up fluids
If
you
have to top up the oil between oil changes,
use the grades of oil specified in the table in ac­
cordance with VW standards.
You will need to know whether
- the vehicLe is being serviced based on the
flexi­

ble or fixed oil change service (see last service
record).
- the vehicle has a petrol or diesel engine (see
sticker on inside of fuel tank flap).
Petrol engines
Diesel engines
Oil Change Service
Flexible
VW 504 00
VW 507 00
Fixed
VW 502 00
With diesel
particulate
fil­

ter:
VW 507 00
Without diesel
particulate
fil­

ter:
VW 505 00
Audi recommends

ÇÇastrol
(MMMM'
FriOFSSskimL

Audi recommends LongLife high-performance
engine oil from Audi Genuine Parts
© Note
If the oil grades specified in the table are not
available, you can use one of the
folLowing

grades as a substitute. To prevent damage to
the engine, this should not be done more
than once between oil changes and no more
than 0.5 litres should be used.
- Petrol engines: ACEA A3 or API SN (API SM)
standard
- Diesel engines: ACEA C3 or API CJ-4 stand­
ard
© Note
The flexible oil change service is not available
for all models in all countries.
Checking and topping up the engine oil
level

The
oil dipstick differs depending on the type of
engine.

Fig.
246 Oil dipstick (examples): Checking engine oil level

Fig.
247 Engine compartment: Engine oil filler cap
(exam-

pLe)
Please refer to the safety notes
opage
295,
Working on components in the engine compart­
ment.
Checking engine oil level
- Park the vehicle on a level surface.
- Switch off the warm engine. Wait for
a
few mi­
nutes for the oil to drain back into the sump.
- Open the bonnet
opage
296.
-
PuLl
out the oil dipstick
^>page
297, Fig. 245,
wipe it with a clean cloth and insert it again,
pushing it in as far as it will go.
- Then pull the dipstick out again and check the
oil level
•=>
table on page 299.
- If the oil level is too Low, add more engine oil.
298

Checking and topping up fluids

CO

<
O
rN
iv
rN
i—i
o <
Markings on oil dipstick
^>Fig.
246

®

CD

(D

0
When the oil level is near the marking
(Î)

you must top up the engine oil. Please refer

to-=>®.

Do NOT add engine oil.
Do NOT add engine oil.
Drive to a qualified workshop without delay
and have the engine oil changed
•=>©.

Topping up the engine oil
- Unscrew the cap
"fc^
^>Fig.
247 from the
oilfill­

er opening
^>page
297, Fig. 245.
-Carefully add 0.5 Litres of suitable engine oil

^>
page 297.
- After two minutes check the oil level once

again.

- If the oil level is too low, add a smaller quantity
of engine oil. The level must always be below
the marking (5)
<^Fig.
246
<=>©.

- Screw the oil filler cap
*£/;
back on and push
the dipstick all the way in.
A WARNING
- Ensure that no engine oil comes into contact
with hot engine components when topping

up:
this could cause a fire.
- The oil filler cap must be properly closed to
prevent oil from squirting onto the hot en­
gine or exhaust system while the engine is
running - risk of fire!
- Wash your skin thoroughly if it comes into
contact with engine oil.
- The engine oil must never drop below the
marking®
^>Fig.
246- risk of engine dam­

age!

- When topping up the engine oil, make sure
that the oil level is not above the marking

@
^Fig.
246, as this may result in damage
to the catalytic converter or to the engine.
Do NOT start the engine. Contact a qualified
workshop to extract the engine oil if neces­
sary.
- Applies to vehicles which have an oil
dip­

stick with area
(3)^
Fig. 246: If you run your
vehicle on diesel fuel of poorer quality than
EN 590 standard
fuel,
the fuel can get into
the engine oil. In this case, the oil level
gradually rises and the quality of the engine
oil decreases. Once the oil level has reached
the marking
@
or the indicator lamp
E

has come on, the engine oil level must not
be corrected by extracting the surplus oil -

risk
of engine damage! The engine oil must
be changed
^>page
34.
- No additives should be used with engine oil.
Any damage caused by the use of such
addi­

tives would not be covered by the factory
warranty.
© For the sake of the environmen
- Never pour engine oil down drains or into
the ground.
-Always observe statutory requirements
when disposing of empty oil canisters.
© Note
Depending on
how
you drive and the condi­
tions in which the car is used, oil consumption
can be up to 0.5
Itr./lOOO
km. Oil consump­
tion is likely to be higher for the first 5,000

km.
The engine oil Level must be checked at
regular intervals, preferably when refuelling
and before setting off on a long trip.
Cooling system
Coolant
The engine cooling system is filled at the factory
with a mixture of conditioned water and coolant
additive. This coolant must not be changed.
The coolant level is monitored by a warning lamp
|
<^page
30. However, we recommend that it
should be checked occasionally.
If you do need to top up the coolant, use a mix­
ture of water and coolant additive. We recom­
mend mixing coolant additive with distilled wa­
ter.
299

Checking and topping up fluids
Coolant additive
The coolant additive contains anti-freeze and cor­
rosion protection agent. Only use one of the
fol­

lowing coolant additives. It is possible to mix
these additives.
Topping up coolant
Coolant additive
G13
G12++
Specification

TL774J

TL 774
G

The amount of coolant additive which needs to
be mixed with the water depends on the temper­
atures to be expected in the winter season. If the
anti-freeze concentration is too Low, the coolant
can freeze and cause engine damage.
Hot regions
Cold regions
Coolant
additive

min.
40%
max. 45 %

min.
50%
max. 55 %
Frost protec­
tion

min.-25°C

max. -40 °C

(T)
CAUTION
- Have your qualified workshop check the
cooling system before the winter season to
make sure that the anti-freeze concentra­
tion is adequate for the conditions to be ex­

pected.
This applies particularly if
you
drive
into a colder climate zone.
- To prevent damage to the engine, do not
use a different type of anti-freeze additive if
the approved type of additive is not availa­

ble.
In this case use only water and bring
the coolant concentration back up to the
correct level as soon as possible by putting
in the specified additive.
- Always top up with fresh, unused coolant.
- Radiator sealants must not be added to the
coolant.

Fig.
248 Engine compartment: Markings on coolant ex­
pansion tank
Please refer to the safety notes
^page
295,

Working on components in the engine compart­
ment.
Checking coolant level

•
Park the vehicle on a level surface.

•
Switch off the ignition.

•
Read off the coolant level on the coolant ex­
pansion tank
^>Fig.
248. When the engine is

cold,
the coolant level should be between the
marks. When the engine is warm, it may be
slightly above the top mark.
Topping up coolant
Important: The coolant expansion tank must not
be empty
•=>([).

•
Wait for the engine to cool down.

•
Cover the cap on the expansion tank with a

cloth,
and carefully unscrew the cap
anti-clock­

wise
<=>
/K.

*-
Add coolant in the correct concentration

tapage
299 up to the top mark.

•
You should make sure that the fluid level re­
mains stable. If necessary, add more coolant.

•
Screw the cap on again tightly.
Any loss of coolant normally indicates a Leak in
the cooling system. Drive to a qualified workshop
without delay and have the cooling system

checked.
If there are no leaks in the system, a
loss of coolant can only occur if the coolant boils
and is forced out of the system as a result of
overheating.
300