Checking and Filling
Fueling procedure
Your vehicle is equipped with a capless fuel filler
system.
Fig. 157 Right rear side of the vehicle: opening the fuel
filler door
- iu
Fig. 158 Right rear side of the vehicle: fuel pump nozzle
inserted
The fuel filler door is unlocked or locked by the
central locking system.
> Unlock the vehicle if necessary.
> Conventional drive system: Press on the left
side of the fuel filler door to open it > fig. 157.
> Plug-in hybrid drive: Pull on the VY switch in the
driver's door. The fuel filler door will open auto-
matically after venting is complete.
> Plug-in hybrid drive: Note the information for
refueling at the end of this chapter.
> Insert the fuel pump nozzle all the way into the
fuel filler neck. Make sure it is seated correctly.
> Begin fueling. Once the fuel pump nozzle turns
off the first time, the fuel tank is full. Do not
continue fueling, or else the expansion space in
the tank will be filled with fuel.
> After the fuel pump has switched off, wait five
seconds before removing the nozzle to allow
the rest of the fuel to finish dripping into the
fuel tank.
256
> Close the fuel filler door and then press on the
left side until it latches.
The correct fuel type for your vehicle can be
found ona label located on the inside of the fuel
filler door. For additional information on fuel, see
=> page 254.
For the tank capacity in your vehicle, refer to the
Technical Data > page 332.
ZA WARNING
Improper fueling procedures and improper
handling of fuel can lead to explosions, fires,
severe burns, and other injuries.
— Do not smoke. Keep away from open flames.
— The ignition must be switched off when re-
fueling.
— Mobile devices, radio devices, and other ra-
dio equipment should always be switched
off when refueling. Electromagnetic rays
could cause sparks and start a fire.
— If you do not insert the fuel pump nozzle all
the way into the filler tube, then fuel can
leak out. Spilled fuel can ignite and start a
fire.
— Never get into the vehicle when refueling. If
there is an exceptional situation where you
must enter the vehicle, close the door and
touch a metal surface before touching the
fuel pump nozzle again. This will reduce the
risk of electrostatic discharge that can cause
flying sparks. Sparks can start a fire when
refueling.
Z\ WARNING
Audi does not recommend transporting fuel
containers inside the vehicle. Fuel could leak
out of the container and ignite, especially dur-
ing an accident. This can cause explosions,
fires, and injuries.
— If you must transport fuel in a fuel contain-
er, note the following:
— Always place the fuel container on the
ground before filling. Never fill the fuel
container with fuel while it is inside or on
Checking and Filling
Read and follow the important safety precautions
=> A\ in Fueling procedure on page 256.
The funnel used for emergency fueling is con-
tained in the vehicle tool kit, which is located in
the luggage compartment under the cargo floor
=> page 305.
> Fold up the cargo floor in the luggage compart-
ment.
> Remove the funnel from the vehicle tool kit.
> Press on the left side of the fuel filler door to
open it > page 256, fig. 157.
> Insert the funnel into the fuel filler neck all the
way until it stops > fig. 159. Make sure that the
ring on the funnel goes into the fuel tank filler
neck.
> Guide the reserve canister filler tube into the
funnel and start the emergency fueling.
> Remove and clean the funnel after the fueling
process. Then close the fuel filler door and
press on it until it latches.
@) Note
Remove fuel that has overflowed onto any ve-
hicle components immediately to reduce the
risk of damage to the vehicle.
Fuel filler door emergency release
Applies to: vehicles with manual fuel filler door release
If the central locking system malfunctions, the
fuel filler door can be unlocked manually.
Fig. 160 Right cover in the luggage compartment: remov-
ing the cover
258
Fig. 161 Luggage compartment: fuel filler door emergency
release
The emergency opening mechanism is located
behind the right cover in the luggage compart-
ment.
> Remove the screwdriver from the vehicle tool
kit > page 305.
> Insert the flat side of the screwdriver carefully
into the slot between the side trim panel and
the cover > fig. 160 (arrows) and pry out the
cover. Keep in mind that a power cable for the
socket is located on the rear side.
> To unlock the fuel filler door, loosen the red
loop from the retainer and then pull on the
loop carefully > fig. 161 >@.
> Press on the left side of the fuel filler door to
open it > page 256, fig. 157.
() Note
Only pull on the loop until you feel resistance.
You
will not hear it release. If you continue to
pull, you could damage the emergency re-
lease mechanism.
G@) Tips
Applies to: vehicles with plug-in hybrid drive
— The tank will not be vented if the emergency
release function was used on the fuel filler
door. You can only fill a small amount of
fuel in the tank. Fill only until the fuel pump
nozzle turns off for the first time. Drive to
an authorized Audi dealer or authorized
Audi Service Facility immediately to have
the malfunction corrected.
— Pressure can escape if you open the tank cap
after using the emergency release. This can
create noises.
Checking and Filling
— Never reach into the radiator fan. The fan is
temperature-controlled and can turn on
suddenly, even when the ignition is switched
off.
— Never open the hood when there is steam or
coolant escaping from the engine compart-
ment, because there is a risk that you could
be burned. Wait until no steam or coolant is
escaping.
— Plug-in hybrid drive: The coolant expansion
tank cap is equipped with a seal that must
never be removed under any circumstances
=> page 262, fig. 164. If the coolant expan-
sion tank for the high-voltage system is not
sealed, please contact an authorized Audi
dealer or authorized Audi Service Facility.
— Plug-in hybrid drive: The sealed cap must
only be opened by an authorized Audi dealer
or authorized Audi Service Facility.
— The cap on the coolant expansion tank must
never be opened when the coolant is hot.
The cooling system is under pressure. There
is a risk of burns
— To protect your face, hands, and arms from
hot steam or coolant, cover the cap with a
thick cloth when opening.
— Do not remove the engine cover under any
circumstances. This increases the risk of
burns.
— Due to the risk of electric shock, never touch
the ignition cable or other components in
the electronic high-voltage ignition system
when the engine is running or is starting.
— If a gear is engaged while the vehicle is sta-
tionary and the engine is running, do not
press the accelerator pedal inadvertently.
Pressing the accelerator pedal will cause the
vehicle to move, and this could result in an
accident.
— If inspections or repairs must be performed
while the engine is running, moving compo-
nents (such as the ribbed belt, generator,
and radiator fan) pose an additional risk.
— Set the parking brake first and select the
“P” (Park) selector lever position.
— Always make sure that no parts of the
body, jewelry, ties, loose clothing, and
long hair can be caught in moving engine
components. Before any work, always re-
move any jewelry and/or ties, tie back long
hair, and make sure all clothing fits close
to the body to reduce the risk of anything
becoming caught in engine components.
— Pay attention to the following warnings list-
ed when work on the fuel system or on the
electrical equipment is required.
— Do not smoke.
— Never work near open flames.
— Always have a working fire extinguisher
nearby.
— All work on the battery or electrical system
in your vehicle can result in injuries, chemi-
cal burns, accidents, or burns. Because of
this, all work must be performed only by an
authorized Audi dealer or authorized Audi
Service Facility.
— Limit your exposure to exhaust and chemi-
cals to as short a time as possible.
ZA WARNING
California Proposition 65 Warning:
— Engine exhaust, some of its constituents,
and certain vehicle components contain or
emit chemicals known to the State of Cali-
fornia to cause cancer and birth defects and
reproductive harm. In addition, certain flu-
ids contained in vehicles and certain prod-
ucts of component wear contain or emit
chemicals known to the State of California
to cause cancer and birth defects or other
reproductive harm.
— Battery posts, terminals and related acces-
sories contain lead and lead compounds,
chemicals known to the State of California
to cause cancer and reproductive harms.
Wash hands after handling.
260
() Note
When filling fluids, be sure not to add any flu-
ids to the wrong reservoirs. Otherwise severe
malfunctions and engine damage will occur.
@) For the sake of the environment
You should regularly check the ground under
your vehicle in order to detect leaks quickly. If >
Checking and Filling
Checking the engine oil level
The engine oil level can be checked in the MMI.
Observe the safety precautions > page 259, Gen-
eral information.
>» Park the vehicle on a level surface.
> Shut the engine off when it is warm.
> Switch only the ignition back on.
> Wait approximately two minutes.
> Applies to MMI: Select on the home screen: VE-
HICLE > Settings & Service > Oil level.
> Read the oil level in the display. Add engine oil
if the bar in the oil level indicator is just below
“min” > page 264.
@) Note
If the engine oil level is too low or too high,
there is a risk of engine damage.
@) Tips
The oil level indicator in the display is only an
informational display. If the oil level is too
low, a minimum oil warning appears in the in-
strument cluster. Add oil and close the hood.
The current oil level will be displayed on the
MMI the next time the ignition is switched on.
@) Tips
The engine oil consumption may be up to
0.5 quart/600 miles (0.5 liter/1,000 km), de-
pending on driving style and operating condi-
tions. In RS models, the oil consumption may
be up to 1 qt/600 mi (0.8 L/1,000 km). Con-
sumption may be higher during the first
3,000 miles (5,000 km). The engine oil level
must be checked regularly. It is best to check
each time you refuel your vehicle and before
long drives.
— Because of the lubrication and cooling of
the engine, combustion engines consume
oil. The oil consumption varies depending
on the engine and may change during the
service life of the engine. Engines generally
consume more oil at the beginning during
the break-in period. Then oil consumption
stabilizes after the break-in period.
264
— Under normal conditions, oil consumption
depends on the quality and viscosity of the
oil, the engine RPM, the climate conditions,
and the road conditions. The dilution of oil
from condensation or fuel residue as well as
the age of the oil also play a role. Because
engine wear increases with mileage, oil con-
sumption will increase again over time until
it may be necessary to replace worn compo-
nents.
Because all these variables play a role, it is
not possible to define an oil consumption
standard. Therefore, the oil level must be
checked regularly.
If you believe that your engine has in-
creased its oil consumption, contact an au-
thorized Audi dealer or authorized Audi
Service Facility to determine the cause.
Please note that an exact oil consumption
measurement must be done with the neces-
sary care and accuracy and may take time.
An authorized Audi dealer or authorized
Audi Service Facility is trained in accurately
measuring the oil consumption.
You can find information on engine oil and
engine oil capacities for the USA at www.
audiusa.com/help/maintenance, or for Can-
ada at www.audi.ca/ca/web/en/
customer-area/care-and-maintenance/
audi-service-schedules.html, or call
800-822-2834.
Adding engine oil
RAZ-0012|
Fig. 165 Engine compartment: engine oil filling opening
cover (example)
Observe the safety precautions > page 259, Gen-
eral information.
4K8012721BF
Wheels
Glossary of tire and loading
terminology
Accessory weight
means the combined weight (in
excess of those standard items
which may be replaced) of auto-
matic transmission, power steer-
ing, power brakes, power win-
dows, power seats, radio, and
heater, to the extent that these
items are available as factory-in-
stalled equipment (whether in-
stalled or not).
Aspect ratio
means the ratio of the height to
the width of the tire in percent.
Numbers of 55 or lower indicate a
low sidewall for improved steer-
ing response and better overall
handling on dry pavement.
Bead
means the part of the tire that is
made of steel wires, wrapped or
reinforced by ply cords and that is
shaped to fit the rim.
Bead separation
means a breakdown of the bond
between components in the bead.
Cord
means the strands forming the
plies in the tire.
Cold tire inflation pressure
means the tire pressure recom-
mended by the vehicle manufac-
turer for a tire of a designated
size that has not been driven for
more than a couple of miles (kilo-
meters) at low speeds in the three
hour period before the tire pres-
sure is measured or adjusted.
Curb weight
means the weight of a motor ve-
hicle with standard equipment in-
cluding the maximum capacity of
fuel, oil, and coolant, air condi-
tioning and additional weight of
optional equipment.
Extra load tire
means a tire designed to operate
at higher loads and at higher in-
flation pressures than the corre-
sponding standard tire. Extra load
tires may be identified as “XL”,
“xl”, “EXTRA LOAD”, or “RF” on
the sidewall.
277
4K8012721BF
Wheels
on page 286. If driving the vehi-
cle when fully loaded, you must
increase the tire pressure to the
maximum specified pressure > A.
Checking and correcting tire
pressure
> Check the tire pressure at least
once per month and also check it
before every long drive.
> Always check the tire pressure
when the tires are cold. Do not
reduce the pressure if it increas-
es when the tires are warm.
>Refer to the sticker > fig. 173
for the correct tire pressure.
>Correct the tire pressure if nec-
esSary.
>Store the new tire pressure in
the MMI & page 293 or
> page 296.
> Check the pressure in the spare
tire*. Always maintain the maxi-
mum temperature that is speci-
fied for the tire.
—Overloading can lead to loss of
vehicle control and increase
the risk of an accident. Read
and follow the important safe-
ty precautions in > page 287.
—The tire must flex more if the
tire pressure is too low or if
the vehicle speed or load are
too high. This heats the tire up
too much. This increases the
risk of an accident because it
can cause the tire to burst and
result in loss of vehicle con-
trol.
—Incorrect tire pressure increas-
es tire wear and has a negative
effect on driving and braking
behavior, which increases the
risk of an accident.
J WARNING
Always adapt the tire pressure
to your driving style and the ve-
hicle load.
@) Note
Replace lost valve caps to re-
duce the risk of damage to the
tire valves.
© For the sake of the envi-
ronment
Tire pressure that is too low in-
creases fuel consumption.
285
4K8012721BF
Wheels
Z\ WARNING
Please note the important safe-
ty precautions regarding tire
pressure > page 284 and load
limits > page 287.
Tires and vehicle load limits
There are limits to the amount of
load or weight that any vehicle
and any tire can carry. A vehicle
that is overloaded will not handle
well and is more difficult to stop.
Overloading can not only lead to
loss of vehicle control, but can al-
so damage important parts of the
vehicle and can lead to sudden
tire failure, including a blowout
and sudden deflation that can
cause the vehicle to crash.
Your safety and that of your pas-
sengers also depends on making
sure that load limits are not ex-
ceeded. Vehicle load includes ev-
erybody and everything in and on
the vehicle. These load limits are
technically referred to as the vehi-
cle’s Gross Vehicle Weight Rating
(“GVWR”).
The “GVWR” includes the weight
of the basic vehicle, all factory in-
stalled accessories, a full tank of
fuel, oil, coolant and other fluids
plus maximum load. The maxi-
mum load includes the number of
passengers that the vehicle is in-
tended to carry (“seating capaci-
ty”) with an assumed weight of
150 lbs. (68 kg) for each passen-
ger at a designated seating posi-
tion and the total weight of any
luggage in the vehicle. If you tow
a trailer, the weight of the trailer
hitch and the tongue weight of
the loaded trailer must be includ-
ed as part of the vehicle load.
The Gross Axle Weight Rating
(“GAWR”) is the maximum load
that can be applied at each of the
vehicle’s two axles.
The fact that there is an upper
limit to your vehicle’s Gross Vehi-
cle Weight Rating means that the
total weight of whatever is being
carried in the vehicle (including
the weight of a trailer hitch and
the tongue weight of the loaded
trailer) is limited. The more pas-
sengers in the vehicle or passen-
gers who are heavier than the
standard weights assumed mean
that less weight can be carried as
luggage.
The Gross Vehicle Weight Rating
and the Gross Axle Weight Rating >
287
Index
Diteetor yess 6 s cscaves ws sacewes v6 aneims v © sxeams 6 0 202
Business card... 6... eee eee eee 203
SCttinGSanww + wuwn x 3 mee ee ReUeE SE eee & 205
Display
Cleaning’s « «sew 2s seas © 2 eww vo ene woe 301
DispOSalis: + = secre 5 5 was 5 ¥ ees eo ee Ge 326
DistanG@ies = : ees = : wes ¢ 2 eee Yo ewe Ye: 17
Distance WarhiiG sca + < sees 2 3 has os eS 164
Doors
Childisafety lock sxe < « same s » ews = 2 eres = 46
Door:comtact:switeh i « sess 2s sansa vo scares a 5 56
Mechanically unlocking and locking....... 39
Power closing/closing aid............... 36
Driver information system................ 13
Drives
refer to Media... ...s0scceees eens 236; 239
Drive select
refer to Audi drive select............... 111
Drive'SySteMm « sessen « swswss 6 2 cae 3 ¥ a0 100, 105
Audi drive select..............000000- 111
DrivingiGOwniBills ecerese © versus ie o vvasene a + wavess 109
Driving programs « x saves vo meses xo esas 6 96, 162
Driving through water............-...0- 110
Driving’ CUIMGls « « seme ss eee so ees eae a 17
Driving tips
Driving through water................- 110
Efficient driving. ..........00 eee ee eee 103
Uphill ahd Gownhill we » s wore 2 x eae o 2 caer 109
Driving track. . 2.2... ee eee ee eee eee 109
Driving uphills...................0000. 109
DVD drive... .. 0.2.02. eee 237
Dynamic all-wheel steering.............. 113
E
BERL l « cncmena eo wwesien we meres so sete sw cane 206
Settings........... 0... e eee eee eee 206
EDL
refer to Electronic Differential Lock...... 115
EDR
refer to Event Data Recorder (EDR)...... 321
Efficienity a8SiSbies « caw x x eews vo eam ex 152
Predictive Comtrobsisin: 0 o seve w scum 2 v sueawe 158
Electrical:system’. « « wessce so wena ee ene soe 269
Electric ranges s ¢ evans s+ meas s ¥ cae 5 2 meee 224
Electromechanical parking brake......... 107
Electronic Differential Lock.............. 116
336
Electronic immobilizer .............0.004. 41
Electronic Stabilization Control........... 115
Embedded SIM: card « « saws x « wwe x s gue 8 209
EMergency:aSsist sasws s ness 3 5 nee so teeE 174
Emergency assistance..............-... 305
Emergency braking function............. 108
Emergency call..............000.. 204, 213
Emergency flashers.............--..00-- 55
Emergency fueling............--..20005 257
Emergency M0de esc + secs es ences oo acee 3 99
Emergency operation
Doors... 2... eee eee eee ee 39
FUSLTINLERGGOF sx ¢ « casas» 2 news a 3 mae 2 a 258
Luggage compartment lid............... 46
Panoramic glass roof.............200005 49
Emissions control system.............. 259
EMeErgy CONSUMENSHs «i iii + asus oo eacem wo 8 18
Energy flow display® wees ¢ s wees s 6 ween s ve 102
Energy management.................5. 104
Etergy TECOVERYase « 2 caps 5 « smerny 5 o eye 101
Engine
Breaking'inl's « sevas « ¢ saves « » newer x 2 Mowe @ 100
COOLANE «, cassne « « snawins = w eeawens © a temsem « areneten 266
Emergency stop. ... 0.06... eee ee eee eee 93
JUMP Starting « + mews s x eews 5 a sowe 4 eee 311
Start/Stop system............-0000005 104
Starting/stopping.............0...00ee 93
Engine braking effect
refer to Recuperation...............-. 101
Engine compartment
Opening and closing the hood.......... 261
OVERVIOW'. score na sesrene a w eaesere oo sieeern a 8 ae 262
Safety precautions..............00000 259
Engine data
refer to Sport displays .............0065- 16
Engine oil
AGING « ccs scorn 2 3 ceveum eo aman oe Eos
Changing
Checking oillevel.............2--000-- 262
CONSUMpPtiON ss ¢ ¢ eees ¢ eee oo ee oo 262
Indicator light........... 0. cece eee eee 263
Replacement interval................. 273
Temperature display................0-. 16
Engine sound
Audi drive:selectii: « ccine os vomem 2 seas ¥ as 112
Engineistartsystem vce + acs 6 2 wanes 6 2 vonse 94