2020 TOYOTA RAV4 engine
[x] Cancel search: enginePage 14 of 64
12
5 I F F O H J O F T X J U D I N V T U C F J O U I F i 0 / w Q P T J U J P O X J U I P V U 4 N B S U , F Z
i * ( / * 5 * 0 /
0 / w N P E F X J U I 4 N B S U , F Z
B O E U I F C S B L F Q F E B M E F Q S F T T F E U P T I J G U G S P N 1 B S L
Shift the shift lever to “S” position from “D” position.
+ 6 Q T I J G U Q V T I B O E S F M F B T F
- % P X O T I J G U Q V M M B O E S F M F B T F
Downshifting increases power going uphill, or provides engine braking downhill. For
best fuel economy during normal driving conditions, always drive with the shift lever
in the “D” position.
Auto lock/unlock
Automatic transmission
Automatic door locks can be programmed to operate in different modes, or turned
OFF.
Shift position linked door locking/unlocking function
-Doors lock when shifting from Park.
-Doors unlock when shifting into Park.
Speed linked door locking function
-Doors lock when the vehicle speed goes above approximately 12 mph.
' U L Y H U
Page 16 of 64
14
Smart KeyWithout Smart Key
Steering lock release
Push Turn
Turn
Turn
When the steering lock cannot be
released, “Push Engine Switch while
Turning Steering Wheel in Either
Direction” will be displayed on the
multi-information display.
Check that the shift lever is set in P.
Press the engine switch shortly and
firmly while turning the steering wheel
left and right.When starting the engine, the engine
switch may seem stuck in OFF. To free
it, turn the key while turning the steering
wheel slightly left and right.
Unlock
Lock
Door locks
Tilt & telescopic steering wheel
Hold wheel, push lever down, set angle and length, and return lever.
NOTE: Do not attempt to adjust while the vehicle is in motion.
Length
Lock release lever
Angle
FEATURES & OPERATIONS
Page 29 of 64
27
FrontRear
OVERVIEW FEATURES & OPERATIONS TOYOTA SAFETY SENSE SAFETY & EMERGENCY FEATURES
Power switchCharge areaOperation indicator light
Qi Wireless charger (if equipped)
A mobile device can be charged wirelessly on the tray. (1) Press the wireless
charger power switch and the green operation indicator light turns on. (2) Place
a compatible mobile device on the tray as shown in the illustration. An amber
indicator illuminates while charging is in progress. When charging is complete, the
indicator illuminates green. Some phones, cases or cover type wireless chargers
may not cause the green indicator to illuminate even though it is fully charged.
Refer to the Owner‘s Manual for limitations and more details on this system before
attempting to use it.
Press (1)
When the engine is turned off, the last state
(ON/OFF) of the charger is memorized.
Place device nearest the center of charging
area for best results. Moving device may
result in stopping or restarting the charging
process.
Place (2)
USB charge-ports (if equipped)
5 I F F O H J O F T X J U D I N V T U C F J O U I F i " $ $ w P S i 0 / w Q P T J U J P O X J U I P V U 4 N B S U , F Z
i " $ $ & 4 4 0 3 : w P S w * ( / * 5 * 0 / 0 / w N P E F X J U I 4 N B S U , F Z
G P S V T F
(Charge only) (Charge only)
Page 33 of 64
31
Stop & Start system (if equipped)
The Stop & Start system stops and starts the engine according to brake pedal
or shift lever operation when the vehicle is stopped, such as at a stoplight,
intersection, etc., in order to improve fuel economy and reduce noise pollution
caused by the engine idling.
Press the Stop & Start cancel switch to disable the Stop & Start system.
The Stop & Start cancel indicator will illuminate. Pressing the switch again will
enable the Stop & Start system and the Stop & Start cancel indicator will turn off.
Refer to the Owner‘s Manual for limitations and more details on this system. Stopping the engine
While driving with the D shift position selected, depress the brake pedal and stop
the vehicle. The engine will stop automatically.
When the engine stops, the Stop & Start indicator will illuminate.
Restarting the engine
Release the brake pedal. The engine will start automatically.
When the engine starts, the Stop & Start indicator will turn off.
STOP & START SYSTEM OPERATION
DISABLING THE STOP & START SYSTEM
OVERVIEW FEATURES & OPERATIONS TOYOTA SAFETY SENSE SAFETY & EMERGENCY FEATURES
Page 41 of 64
39
CHANGING PRE-COLLISION ALERT TIMING
% * 4 " # - * / ( 1 3 & $ 0 - - * 4 * 0 / 4 : 4 5 & . 1 $ 4
Each time the PCS switch is pressed, the response to the PCS alert timing changes.
FarMiddle
(default)Near
1 S F T T “ ” switches and select “” G S P N U I F . V M U J * O G P S N B U J P O % J T Q M B Z . * %
1 S F T T “
” switches and select “ PCS” and then press “.” The setting
screen is displayed.
1 S F T T “
” switches and select “Sensitivity” and then press “” to select
the desired setting. Each time it is pressed, the response to the PCS alert timing
changes as shown above.
1ress “
” to go back to the menu.
Note: PCS is enabled each time the engine switch is turned to Ignition On.
The system can be disabled/enabled and the alert timing of the system can be
changed. (Alert timing only, brake operation remains the same).
1 S F T T “
” switches and select “” G S P N U I F . V M U J * O G P S N B U J P O % J T Q M B Z . * %
1 S F T T “
” switches and select “ PCS” and then press “.”
1 S F T T “
” and select “PCS” and then press “” to select the desired setting.
1 S F T T “
” to go back to the menu.
Note: The system is enabled each time the power switch is turned to ON mode.
Refer to the Toyota Owner’s Manual for additional information on PCS operation,
settings adjustments, limitations, and precautions before attempting to use it.
OVERVIEW FEATURES & OPERATIONS TOYOTA SAFETY SENSE SAFETY & EMERGENCY FEATURES
Page 52 of 64
50
TOYOTA SAFETY SENSE™
" % + 6 4 5 * / ( % * 4 5 " / $ & $ 0 / 5 * / 6 & %
Note: When your vehicle is too close to a vehicle ahead, and sufficient automatic
deceleration via the cruise control is not possible, the display will flash and the
buzzer will sound to alert the driver. An example of this would be if another driver
cuts in front of you while you are following a vehicle. Depress the brake pedal to
ensure an appropriate vehicle-to-vehicle distance.
Acceleration when there are no longer any preceding vehicles driving
slower than the set speed
The system accelerates until the set speed is reached. The system then
returns to constant speed cruising.
4 8 * 5 $ ) * / ( 5 0 $ 0 / 4 5 " / 5 4 1 & & % $ 3 6 * 4 &
$ 0 / 5 3 0 - . 0 % &
4 & 5 5 * / ( $ 0 / 4 5 " / 5 4 1 & & % $ 3 6 * 4 &
$ 0 / 5 3 0 -
If you are already using DRCC “”, push ON-OFF button to turn the system off
first, then push and hold ON-OFF button for at least 1.5 seconds to switch.
Note: When the engine is turned off, it will automatically default to DRCC.
Refer to the Toyota Owner’s Manual for additional information on DRCC operation,
settings adjustments, limitations, and precautions before attempting to use it.
1.5 seconds
Set
To adjust speed or cancel, see steps (2) and (3) of ADJUSTING SET SPEED on
page 48.
Page 54 of 64
52
TOYOTA SAFETY SENSE™
Road Sign Assist (RSA)
Road Sign Assist is designed to help ensure drivers are kept informed. The RSA
system recognizes specific road signs using a forward-facing intelligent camera to
Q S P W J E F J O G P S N B U J P O U P U I F E S J W F S W J B B . V M U J J O G P S N B U J P O % J T Q M B Z . * %
* G U I F T Z T U F N
judges that the vehicle is being driven over the speed limit, or performing actions
prohibited by other support types of road signs, it alerts the driver using a warning
display and may sound a warning buzzer.
RSA DISPLAY
SUPPORTED TYPES OF ROAD SIGNS
SETTING RSA
When the driving support system
information is selected, a maximum of
3 signs can be displayed.
Speed limit Stop
Do Not Enter YieldWhen a tab other than the driving
support system information is selected,
only a recognized speed limit sign or
E P O P U F O U F S T J H O X I F O O P U J G J D B U J P O J T
O F D F T T B S Z
X J M M C F E J T Q M B Z F E
1 S F T T “
” switches and select “” G S P N U I F . V M U J * O G P S N B U J P O % J T Q M B Z . * %
1 S F T T “
” switches and select “ RSA” and then press “.”
1 S F T T “
” switches and select the “Road Sign Assist on/off” setting function
and then press “
.”
1 S F T T “
” to go back to the menu.
Note: If the engine switch was last turned off while a speed limit sign was
displayed on the multi-information display, the same sign displays again when
the engine switch is turned to ON.
Refer to the Toyota Owner’s Manual for additional information on RSA operation,
settings adjustments, limitations, and precautions before attempting to use it.
Page 59 of 64
57
Floor mat installation
There are two types of Toyota floor mats: carpeted and all-weather. Each vehicle
has model-specific floor mats. Installation is easy.
To keep your floor mat properly positioned, follow these steps:
• Only use Toyota floor mats designed for your specific model.
• Use only one floor mat at a time, using the retaining hooks to keep the mat in
place.
• Install floor mats right side up.
5 3 " $ 5 * 0 / $ 0 / 5 3 0 - 5 3 " $
VSC helps prevent loss of traction during cornering by reducing engine power, and
Traction Control helps maintain traction on loose gravel and wet, icy, or uneven
T V S G B D F T C Z B Q Q M Z J O H C S B L F G P S D F U P U I F T Q J O O J O H X I F F M T
Toyota’s TRAC sensors are activated when one of the drive wheels starts to slip.
TRAC limits engine output and applies the brakes to the spinning wheel. This
transfers power to the wheels that still have traction to help keep you on track.
Always align the C marks
OVERVIEW FEATURES & OPERATIONS TOYOTA SAFETY SENSE SAFETY & EMERGENCY FEATURES