2020 INFINITI Q50 ignition

7
To use the door handles to lock
and unlock your vehicle, make
sure the INFINITI Intelligent
Key is with you (that is, in your
pocket or purse).
•

T
ouch the inside of the door
handle
to unlock the
corresponding front door.
•


Pushing the r
equest switch
while touching the inside
of the door handle will unlock
the rest of the doors.
•


T

o lock the vehicle,
push either door handle
request switch
once.
Locking and Unlocking your
Vehicle via the Door Handle
To change the settings for the door locking and unlocking system,
press the MENU button
, then select the “Settings” key on the
lower display followed by the “Comfort & Convenience” key.
•


T

o unlock all doors by touching the
inside of the door handle, select
“Selective Door Unlock”.
•


T

o disable unlocking by touching the
inside of the door handle, select “Touch Sensitive Door Sensor”.
Please see your Owner’s Manual for important safety information, system limitations, and
additional operating and feature information.
Two positions for the driver’s seat, steering column and outside
mirrors can be stored in the automatic drive positioner memory. To set
a memory position:
1.


Plac
e the ignition switch in the ON position. (The vehicle should
be stopped while setting the memory.)
2.


A
djust the driver’s seat, steering column and outside mirrors
to the desired positions using the adjusting switches
for each feature.
3

.
Push the
SET switch
, and within 5 seconds, push the memory
switch (1 or 2)
. The indicator light for the memory switch you
select will illuminate for approximately 5 seconds and a chime will
sound when the memory is stored.
The driver’s seat and steering column
will automatically move when the
driver’s side door is opened, to
allow the driver to get in and out of
the driver’s seat more easily. “Lift
Steering upon Exit” and “Slide Driver
Seat Back on Exit” can be adjusted in
the lower touch-screen display under
“Comfort & Convenience”.
Please see your Owner’s Manual for important safety information, system limitations, and
additional operating and feature information.
Automatic Drive Positioner
(if so equipped)

8
Starting/Stopping the
EngineHomeLink® Universal Transceiver
(if so equipped)
HomeLink
It is important to make sure
the INFINITI Intelligent Key
is with you (that is, in your
pocket or purse).
1.


Depr
ess the brake pedal.
2.


Push the ignition swit
ch
START/STOP button to
the ON position.
TURNING THE ENGINE OFF
1.


M
ove the shift lever to the P (PARK) position
and apply the parking brake.
2.


Push the ignition swit
ch START/STOP button
to turn the engine off.
Please see your Owner’s Manual for important safety information,
system limitations, and additional operating and feature information.
To program the HomeLink® Universal Transceiver: 1.

P
osition the handheld transceiver 1-3 in (26-76 mm) away from the HomeLink
surface, keeping the HomeLink indicator light in view.
2.



Pr

ess and hold the desired HomeLink button and the handheld transmitter button
simultaneously until the HomeLink indicator light flashes slowly and then rapidly.
3

.

Bo

th buttons may be released when the indicator light flashes rapidly.
4.



Pr

ess and hold the programed HomeLink button and observe the indicator light.
A solid, continuous light indicates the programing is complete. If the indicator light
rapidly blinks for two seconds and then turns to a solid, continuous light, continue
with steps for a rolling code device.
5.



A

t the receiver located on the garage door opener motor, locate the “learn” or
“smart” button. If there is difficulty locating the button, reference the garage door
opener’s manual. Once the button is pressed, you have approximately 30 seconds to
initiate the next step.
6.



Pr

ess and hold the programed HomeLink button for two seconds and release. Repeat
the sequence up to three times to complete the programing process. HomeLink should
now activate your rolling code equipped device.
Please see your Owner’s Manual for important safety information, system limitations, and additional operating and
feature information.

10
To turn the rain sensor function on and off:
1.

Pr
ess the MENU button below the lower display.
2.


Select the
“Settings” key and then the “Comfort &
Convenience” key
on the display.
3

.



Select the

“Rain Sensor” key
to toggle the
feature ON and OFF.
When the rain-sensing function is disabled, the AUTO
position on the wiper stalk will work in conventional
intermittent mode.
WIPER BLADE REPLACEMENT PROCEDURE
The windshield wipers must be in the service position in order
to replace the wiper blades. To move the wiper blades to the
service position:
• When the ignition swit

ch is in the ON position or within
60 seconds of placing the ignition switch in the OFF
position, lift the windshield wiper and washer lever
upwards twice in less than 0.5 seconds. The windshield
wipers will move to the service position automatically, and
the wiper blades can now be replaced.
To move the wiper blades back to the original position:
•


Plac

e the wiper arm in the down position and lift the wiper
and washer lever up for more than 1 second, or lower the
lever down to operate at any wiper speed.
Wiper and Washer Switch
Move the lever up or down to one of
the following positions to operate the
windshield wipers:
MIST
One sw

eep operation
OFF

Wipers ar

e OFF
AUTO

Speed-sensing and
r

ain-sensing automatic wipe
LO



C

ontinuous wipe, slow
HI

C

ontinuous wipe, fast
To adjust the wiper sensitivity for the AUTO
setting, twist the control ring
.
Pull the lever
toward you to operate the
windshield washer.
Please see your Owner’s Manual for important safety information, system limitations, and additional operating and feature information.

11
Vehicle Information Display
The vehicle information display will provide warnings and information
for items such as:
USING THE VEHICLE INFORMATION DISPLAY
To change the displayed item on the vehicle information
display
, press the or button on the steering wheel.
The odometer and twin trip odometer are displayed in the vehicle
information display when the ignition switch is in the ON position.
RESETTING THE TRIP ODOMETER
Pushing the TRIP RESET switch
under the combination meter
panel changes display to TRIP A or TRIP B.
Pushing the TRIP RESET switch
for more than 1 second resets
the trip odometer to zero.
Please see your Owner’s Manual for important safety information, system limitations, and
additional operating and feature information.
• Automatic Transmission (AT)
•


All-
Wheel Drive (AWD)
•


Cruise C
ontrol
•


In
telligent Cruise Control (ICC)
•


A
ctive Lane Control
•


Lane Departur
e Warning (LDW)/
Lane Departure Prevention (LDP)
•


Blind Spo
t Warning (BSW)
•


Blind Spo
t Intervention
® (BSI)
•
Back-up Collision
Intervention (BCI)
•

Dist
ance Control Assist (DCA)
•

Forward
Emergency Braking (FEB)
•
Predictive Forward
Collision Warning (PFCW)
•
Active Trace Control •
In telligent Key System