2020 GENESIS G90 Owner's Manual

The Blind-Spot View Monitor system
displays the left or right side of the
rear blind spot area of your vehicle in
the instrument cluster when the left
or right turn signal is on. This function
helps you drive safely when chang-
ing lanes.
The system is activated when thefollowing steps are performed.
1. The engine is running.
2. The turn signal is turned on.
The system is deactivated when one of the following is performed.
- The Engine Start/Stop button is inthe OFF position.
- The turn signal is turned off
- The hazard warning flasher is on
- A warning screen pops up and takes priority over the Blind-Spot
View Monitor system.
3-116
Convenient features of your vehicle
B BL
LI
IN
N D
D-
-S
S P
PO
O T
T
V
V I
IE
E W
W
M
M O
ON
NI
IT
T O
O R
R
S
S Y
Y S
ST
TE
EM
M
This system is a supplemental
system only. It is the responsi-
bility of the driver to always
check the area around the
vehicle before and while mak-
ing turns or changing lanes.
ALWAYS look around your vehicle to make sure there are
no objects or obstacles
before moving the vehicle in
any direction to prevent a col-
lision.
Objects are closer than they appear. Failure to visually
confirm that is safe to change
the lane before doing so may
result in crash and serious
injury or death.
Always keep the camera lens clean. The camera may not
work normally if the lens is
covered with foreign sub-
stance.
WARNING
OHI048526
■ Left
■Right
OHI048527

3-117
0
03
3
A
A U
U T
TO
O M
M A
AT
TI
IC
C
C
C L
LI
IM
M A
AT
TE
E
C
C O
O N
NT
TR
R O
O L
L
S
S Y
Y S
ST
TE
EM
M
Front
1. Driver's temperature control knob
2. Driver's AUTO button
3. Driver's mode selection button
4. Front windshield defroster button
5. Rear window defroster button
6. SYNC button
7. AQS (Air quality system) button
8. Air intake control button
9. Passenger's mode selection button
10. Passenger's temperature control
knob
11. Passenger's AUTO button
12. Driver's fan speed control button
13. OFF button 14. Climate control information screen
selection button
15. Air conditioning button
16. Passenger's fan speed control button
Rear
17. Rear fan speed control knob
18. Rear mode selection button
19. Rear OFF button
20. Rear AUTO button
21. Rear temperature control knob
22. LCD display
■
■Front
■ Rear
OHI048339L/OHI048302L

3-118
Convenient features of your vehicle
Automatic Heating and Air
Conditioning
The Automatic Climate Control System
is controlled by setting the desired tem-
perature.
1. Press the AUTO button.
The modes, fan speeds, air intake
and air-conditioning will be controlled
automatically by the temperature set-
ting you select.2. Turn the temperature control knob
to the desired temperature. If the
temperature is set to the lowest
setting (Lo), the air conditioning
system will operate continuously.
After the interior has cooled suffi-
ciently, adjust the knob to a higher
temperature set point whenever
possible.
To turn the automatic operation off,
select any function of the following:
- Mode selection button
- Air conditioning button
- Front windshield defroster button (Press the button one more time to
deselect the front windshield
defroster function. The 'AUTO' sign
will illuminate on the climate infor-
mation screen once again.)
- Fan speed control button
OHI048305
■
Driver's side
OHI048308
OHI048307
■Front
Driver's side Passenger's side
■ Passenger's side
■Rear

3-119
0
03
3
The selected function will be con-
trolled manually while other functions
operate automatically.
For your convenience and to improve
the effectiveness of the climate con-
trol, use the AUTO button and set the
temperature to 72°F (22°C).
Information
Never place anything near or covering
the sensor (both inside and outside the
vehicle) to ensure better control of the
heating and cooling system.
Manual Heating and Air
Conditioning
The heating and cooling system can
be controlled manually by pushing
buttons other than the AUTO button.
In this case, the system works
sequentially according to the order of
buttons selected.
When pressing any button except the
AUTO button while using automatic
operation, the functions not selected
will be controlled automatically.
1. Start the engine.
2. Set the mode to the desired posi-
tion.
To improve the effectiveness of heating and cooling, select the
mode according to the following:
- Heating:
- Cooling:
3. Set the temperature control to the desired position.
4. Set the air intake control to Fresh mode.
5. Set the fan speed control to the desired speed.
6. If air conditioning is desired, turn the air conditioning system on.
7. Press the AUTO button in order to convert to full automatic control of
the system.
The climate control system settings
will be maintained, even when the
engine is turned OFF. However, the
climate control system settings will
be initialized when the battery has
been discharged, or when the cables
have been disconnected. In this
case, adjust the climate control sys-
tem settings again.
i
OHI048309

3-120
Convenient features of your vehicle
Mode selection
OHI048312

G90 is equipped with temperature sensors inside the side outlet vents to
accurately measure and control air temperature both in the driver's seat and
the front passenger's seat. However, when the side outlet vents are closed,
the temperature sensor will measure air temperature only inside the side out-
let vents. For accurate temperature control, open the side outlet vents.

The rear outlet vents are controlled by the rear climate control system.

3-121
0
03
3
Front mode selection button
The mode selection button controls
the direction of the air flow through
the ventilation system.
The air flow outlet direction is cycled
as follows:
Information
The passenger's side cannot select the
Floor & Defrost ( ) mode. Face-Level (B, C, D, F, G)
Air flow is directed toward the upper
body and face. Additionally, each
outlet can be controlled to direct the
air discharged from the outlet.
A small amount of air blows from the
floor air vents to help provide pleas-
ant air quality inside the passenger
compartment.
Bi-Level (B, C, D, E, F, G)
Air flow is directed towards the face
and the floor.
Floor & Defrost (A, C, D, E)
Most of the air flow is directed to the
floor and the windshield with a small
amount directed to the side window
defrosters.
Floor-Level (A, C, D, E)
Most of the air flow is directed to the
floor, with a small amount of the air
being directed to the windshield and
side window defrosters.
i
OHI048310
■ Driver's side ■Passenger's side

3-122
Convenient features of your vehicle
Rear mode selection button
If you press the rear mode selection
button, you can adjust the rear mode
individually.
To adjust the rear mode individually,
go to the AVN system screen and
select 'Setup →General Settings'
and deselect 'Lock Rear Controls'
(the RSE LOCKED indicator on the
rear armrest will turn off). If the 'Lock
Rear Controls' is selected (the RSE
LOCKED indicator on the rear arm-
rest will turn on), the rear mode will
operate same as the front mode.
For more information on the RSE
LOCKED indicator, refer to “Rear
Switches Operating Limitation” in
chapter 2.
The air flow outlet direction is cycled
as follows:
Face-Level (F, G)
Air flow is directed toward the upper
body and face Bi-Level (E, F, G)
Air flow is directed toward the face
and floor
Floor-Level (E)
Air flow is directed toward the floor.
Defrost-Level (A, D)
Most of the air flow is directed to the
windshield with a small amount of air
directed to the side window defrosters.
Information
The rear climate control system will be
deactivated if the fan speed is set to the
highest position with the front wind-
shield defroster button ON. However, if
the rear climate control switch is oper-
ated, the system will reactivate.
i
OHI048311
OHI048313

3-123
0
03
3
Instrument panel vents
The instrument panel vent air flow
can be directed up/down or left/right
using the vent adjustment lever.
The air flow can be closed using the
thumbwheel. To close the vent rotate
it left ( ). To open the vent, rotate it
right ( ).
Temperature control
The temperature will increase by
turning the knob to the right. The
temperature will decrease by turning
the knob to the left. The temperature
will increase or decrease by 1°F
(0.5°C). When set to the lowest tem-
perature setting, the air conditioning
will operate continuously.
Temperature conversion
If the battery has been discharged or
disconnected, the temperature mode
display will reset to Centigrade.
To change the temperature unit from
°C to °F or °F to °C :
- Automatic climate control system
Press the AUTO button for 3 sec-
onds while pressing the OFF but-
ton.
OHI048315
■ Front
■Rear
OHI048308
OHI048307
■Front
Driver's side Passenger's side
■ Rear