2020 AUDI Q7 tire pressure

Care and cleaning


height and width of the inside of the car
wash.
ZA WARNING
—To reduce the risk of accidents, only wash
the vehicle when the ignition is off and fol-
low the instructions from the car wash
operator.
—To reduce the risk of cuts, protect yourself
from sharp metal components when wash-
ing the underbody or the inside of the wheel
housings.
— After washing the vehicle, the braking effect
may be delayed due to moisture on the
brake rotors or ice in the winter. This in-
creases the risk of an accident. The brakes
must be dried with a few careful brake appli-
cations.
—To reduce the risk of paint damage, do not
wash the vehicle in direct sunlight.
—To reduce the risk of damage, do not wash
decorative decals* with a pressure washer.
—To reduce the risk of damage to the surface,
do not use insect removing sponges, kitchen
sponges, or similar items.
— When washing matte finish painted vehicle
components:
— To reduce the risk of damage to the sur-
face, do not use polishing agents or hard
wax.
— Never use protective wax. It can destroy
the matte finish effect.
@) Note — Do not place any stickers or magnetic
signs on vehicle components painted with
matte finish paint. The paint could be
damaged when the stickers or magnets
are removed.

— If you wash the vehicle in an automatic car
wash, you must fold the exterior mirrors in
to reduce the risk of damage to the mirrors.
Power folding exterior mirrors* must only
be folded in and out using the power folding @) For the sake of the environment
function.
—To reduce the risk of damage to the rims
and tires, compare the width between the
wheels on your vehicle with the distance be-
tween the guide rails in the car wash.
—To reduce the risk of damage, compare the
height and width of your vehicle with the
Only wash the vehicle in facilities specially de-
signed for that purpose. This will reduce the
risk of dirty water contaminated with oil from
entering the sewer system.
Cleaning and care information
When cleaning and caring for individual vehicle are not listed, consult an authorized Audi dealer
components, refer to the following tables. The or authorized Audi Service Facility. Also follow
information contained there is simply recommen- __ the information found in > A.
dations. For questions or for components that
Exterior cleaning



Component Situation Solution
Windshield wiper | Deposits Soft cloth with glass cleaner > page 55
blades
Headlights/ Deposits Soft sponge with a mild soap solution®
Tail lights
Sensors/ Deposits Sensors: soft cloth with a solvent-free cleaning solution
camera lenses Camera lenses: soft cloth with an alcohol-free cleaning sol-
ution
Snow/ice Hand brush/solvent-free de-icing spray >

268

4M1012721BA
Emergency assistance

Emergency assistance
General information
> Park the vehicle as far as possible from moving
traffic in the event of a breakdown. In the event
of a flat tire, park the vehicle ona level surface.
If you are ona steep hill, be especially careful.
> Set the parking brake.
> Switch the emergency flashers on.
> Have the passengers exit the vehicle. They
should move to a safe place, for example be-
hind a guard rail.


Follow the steps given above. This is for your
protection and the for the safety of others on
the road.

Equipment
Vehicle tool kit

vehicle jack
Applies to: vehicles with the vehicle tool kit, tire mobility kit,
and vehicle jack

Fig. 176 Luggage compartment: cargo floor cover
The vehicle tool kit, vehicle jack*, tire mobility
kit*, and compressor* are stored in the luggage
compartment under the cargo floor cover
> fig. 176.
> Lift the cargo floor using the handle > fig. 176.
=

The vehicle jack* does not require any mainte-
nance.

Tire mobility kit
Applies to: vehicles with tire mobility kit
> Read and follow the important safety precau-
tions > page 273.
>» Set the parking brake.
> Select the “P” position.
> Check if a repair with the tire mobility kit is pos-
sible > page 273.

UE Raimi) sala
Applies to: vehicles with tire mobility kit

B8U-0100



Fig. 177 Tire: tire damage that cannot be repaired
The tire repair is only meant for temporary use.
Change the damaged tire as soon as possible
SA.
If the tire is pierced by an object such as a nail,
do not remove the object from the tire.
The tire mobility kit can be used at temperatures
as low as -4 °F (-20 °C).
The tire mobility kit must not be used:
—If the tire has cuts or punctures that are larger
than 0.16 in (4 mm) @ © fig. 177
— If the rim is damaged (2)
— If you have driven with very low tire pressure or
without air in the tire @)
See an authorized Audi dealer or authorized Audi
Service Facility for assistance in these situations.

A WARNING
— Please note that the tire mobility kit cannot
be used in all situations, and that it may on-
ly be used temporarily. >

273

Emergency assistance


— The tire sealant must not come in contact
with skin, eyes, or clothing.
— If tire sealant comes into contact with your
eyes or your skin, thoroughly rinse the af-
fected area immediately with clean water.
— Do not inhale the fumes.
— If you swallow any of the tire sealant, thor-
oughly rinse your mouth immediately and
drink a lot of water. Do not induce vomiting.
Seek medical attention immediately.
— Change your clothing immediately if it
comes into contact with tire sealant.
— If an allergic reaction occurs, seek medical
attention immediately.
— Keep the tire sealant away from children.
G) Tips
— If sealant leaks, allow it to dry in place. You
can then peel it off like a sticker.
— Note the expiration date on the sealant bot-
tle. Replace the tire sealant at an authorized
Audi dealer or authorized Audi Service Fa-
cility.
— Radio reception can be interrupted when
operating the compressor.
— Follow the legal regulations that are appli-
cable in the country where you are operating
the vehicle.


eee ma ety
Applies to: vehicles with tire mobility kit






Fig. 178 Components of the tire mobility kit

D_ The compressor may look different. However, the way it is
operated is generally the same.
274


Fig. 179 Tire mobility kit connection
Requirement: the tire mobility kit must be laid
out and ready for use > page 273.
Setting up the tire mobility kit
> Open the cover @ on the compressor!)
> fig. 178.
» Remove the connector (4) and pressure hose ()
from the housing.
> Connect the compressor pressure hose © to
the flange © on the tire sealant bottle @.
> Insert the sealant bottle with the flange at the
bottom into the opening @) on the compressor
cover or the top side of the compressor hous-
ing.
> Remove the valve cap from the faulty tire.
> Install the filler hose @) on the valve (7)
> fig. 179.
> Connect the plug @) > fig. 178 to an outlet in
the vehicle.
> Switch the ignition on.
Inflating a tire
> Move the switch (8) > fig. 179 on the compres-
sor into position I.
> Inflate the tire to between 29 psi (200 kPA)
and 36 psi (250 kPA) and read the pressure on
the gauge.
> If this tire pressure is not reached, remove the
filler hose. Drive slowly approximately 33 feet
(10 m) forward or in reverse so that the sealant
can be distributed in the tire. Inflate the tire
again > A\.

4M1012721BA
Emergency assistance


ZA\ WARNING
— Read and follow the manufacturer's safety
precautions on the compressor and in the in-
structions on the bottle of sealant.
— Ifa tire pressure of 29 psi (200 kPA) cannot
reached after inflating for 6 minutes, then
the tire is too severely damaged. Do not con-
tinue driving.
— If the tire cannot be repaired with the tire
sealant, see an authorized Audi dealer or au-
thorized Audi Service Facility for assistance.

G) Tips
Do not operate the compressor for more than
six minutes continuously, or it can overheat.
Once the compressor has cooled, you can con-
tinue to use it.
Completing
Applies to: vehicles with tire mobility kit
> Affix the sticker that says "max. 50 mph (max.
80 km/h)" that is provided with the tire mobili-
ty kit within the driver's field of vision.
> Stop the vehicle after driving for about 10 mi-
nutes and check the tire pressure.
> If the tire pressure is lower than 19 psi (130
kPA), then the tire is too severely damaged. Do
not continue driving.

ZA\ WARNING
Pay attention to the following after repairing
the tire:
— Do not drive faster than 50 mph (80 km/h).
— Avoid hard acceleration or braking and driv-
ing fast around curves.
— The vehicle may become more difficult to
control.
— If the tire is too severely damaged, see an
authorized Audi dealer or authorized Audi

Service Facility for assistance.

@ For the sake of the environment
You can give the used tire sealant bottle to an
authorized Audi dealer or authorized Audi
Service Facility for disposal.

@) Tips
Remember to obtain a new bottle of sealant
from an authorized Audi dealer or authorized
Audi Service Facility after repairing a tire.
Replacing wheels
You must complete the preparation before
changing a tire.
> Read and follow the important safety precau-
tions > page 273.
> Set the parking brake.
> Select the “P” position.
» When towing a trailer: disconnect the trailer
from your vehicle.
> Lay out the vehicle tool kit > page 273 and the
spare tire.
> Applies to: vehicles with air suspension: Select
on the home screen: VEHICLE > Settings &
Service > Air suspension: wheel change.
> Switch the ignition off.

ZA\ WARNING
The vehicle must also be secured to prevent it
from rolling when using the vehicle jack*. Use
suitable objects to block the front and back of
the wheel that is diagonal from the wheel
with the flat tire.



i
Fig. 180 Wheel: wheel bolts with caps
@

Oo-q
th.
is y
> Slide the plastic clip from the vehicle tool kit
onto the cap until it engages > fig. 180.
> Remove the cap with the plastic clip.
275

Emergency assistance

> Remove the rest of the wheel bolts.
> Remove the wheel >(). The alignment pin re-
mains in the hole while doing this.
Installing a wheel
Read the directions on > page 278 when instal-
ling unidirectional tires.
> Slide the wheel on over the alignment pin >@.
> Install the wheel bolts and tighten them gently
using the hex socket.
> Remove the alignment pin and tighten the re-
maining wheel bolt.
> Carefully lower the vehicle using the vehicle
jack*.
> Tighten the wheel bolts in a diagonal pattern
using the wheel wrench.
The wheel bolts must be clean and loosen and
tighten easily. Check the contact surfaces for the
wheel and hub. Contaminants on these surfaces
must be removed before installing the wheel.

ZA\ WARNING
— Read and follow the important information
and notes under > page 253.
— Never use the hex socket in the screwdriver
handle to tighten the wheel bolts. Using the
hex socket will not achieve the required
tightening torque, which increases the risk

of an accident.
©) Note
When removing or installing the wheel, the
rim
could hit the brake rotor and damage the
rotor. Work carefully and have a second per-
son help you.
Unidirectional tires
A unidirectional tire profile is identified by arrows
on the tire sidewall that point in the running di-
rection. You must always maintain the specified
running direction. This is necessary to ensure the
tire's optimal performance in regard to adhesion,
running noise, and friction, and to reduce the risk
of
hydroplaning.

To benefit fully from the advantages of the uni-
directional tire design, you should replace faulty
278
tires as soon as possible and restore the correct
running direction on all of the tires.
> Reinstall the caps on the wheel bolts if necessa-
ry.
> Store the vehicle tool kit in its designated
place.
> Store the replaced tire securely in the luggage
compartment > page 82.
» Check the tire pressure on the installed wheel
as soon as possible.
> Correct the tire pressure and store it in the MMI
=> page 265.
> The wheel bolt tightening specification must be
120 ft lbs (160 Nm). Have it checked as soon as
possible with a torque wrench. Drive carefully
until then.
> Have the faulty wheel replaced as quickly as
possible.
Jump starting
You should only perform the steps that follow if
you have the necessary tools and technical ex-
pertise.
If the engine does not start because the vehicle
battery is drained, you can jump start your vehi-
cle using another vehicle. Jump start cables are
needed to do this.
Both vehicle batteries must have 12 V nominal
voltage. The voltage capacity (Ah) of the vehicle
battery that is giving power must not be less
than the capacity of the drained vehicle battery.
Jump start cable
Only use a jump start cable with a large enough
diameter. Note the manufacturer's specifica-
tions.
Only use a jump start cable with insulated termi-
nal clamps.
Positive cable - usually red.
Negative cable - usually black.

Fuses and bulbs












Fuse panel () (black) Fuse panel (2) (black)
8 | Front MMI display Luggage compartment lid central locking,
9 | Instrument cluster 11 | fuel filler door, luggage compartment cov-
10 |MMI/DVD drive er
11 | Light switch, switch panels 12 |Luggage compartment lid control module
12 | Steering column electronics Fuse panel (2) (red)
13 | Volume control No. Equipment
14 | MMI Infotainment system control module 1 | Rear climate control system blower
15 | Steering column adjustment 2 |Sound-amplifier
16 | Steering wheel heating 3 | Exhaust treatment, sound actuator
4 |Rear climate control system control panel
Fuse assignment - Left side of the luggage 5 | Right trailer hitch light
6 |Trailer hitch positioning motor
7 |Trailer hitch release
8 | Left trailer hitch light
9 | Trailer hitch socket
ele
a
i] a rE ia) °
U i)

TCE |

Fig. 197 Left side of the luggage compartment: fuse panel
with plastic clip

BR oO All wheel drive sport differential

Bh BR
Exhaust treatment, right rear seat adjust-
ment




















Fuse panel (@) (black)
No. | Equipment
5 |Air suspension
6 |Automatic transmission
7 Rear seat heating, control panel for rear
climate control
Third row seat adjustment
9 | Left tail light
10 | Front belt tensioner on driver's side

12 | Driver’s side rear safety belt tensioner
Fuse | (3) (
No. | Equipment
Driver assist systems control module
2 |Audi phone box, roof antenna
3 Front seat electronics, right lumbar sup-
port
4 |Side assist
5 | Rear Seat Entertainment preparation
Tire pressure monitoring system
8 Parking heater radio receiver, fuel tank
monitoring
10 TV tuner, data exchange and telematics
control module
11 | Vehicle opening/start (NFC)
12 | Garage door opener
13 | Rearview camera, peripheral cameras
14 | Central locking, right tail light
15
|Passenger’s side rear safety belt tensioner
16 Front belt tensioner on front passenger's

side


286

Technical data
Gross Axle Weight Rating (GAWR)


B8U-0380 The maximum permitted load on the front axle
@ or the rear axle @) is listed on the safety cer-
tificate on the side area of the door or on the
driver's door pillar.
Load

The maximum permitted load is listed on the tire
pressure label on the driver's door pillar.
Fig. 200 Safety certificate
Roof load
Gross Vehicle Weight Rating (GVWR) The maximum permissible roof load is 220 lbs
The maximum permitted total weight @ of the (100 kg).
vehicle is listed on the safety certificate on the
side area of the door or on the driver's door pillar.
Trailer load
7,700 lbs (3,500 kg) 770 lbs (350 kg)
298

4M1012721BA
Index

Peripheral cameras.............--00005 158
Personal route assistance............... 194
Phone
Answering/ending acall............... 171
Connecting a second mobile device...... 166
Disconnecting a mobile device.......... 167
SEEMS iccais + w nesses o o wien 6 evamwnn © emaxua 3 175
Phonebook
refer to Contacts........ 2... cee eee eee 170
Playback (media). . ciescoe es ceca ae acme oo ace 215
Podcast
refer to Online radio...............00. 206
POL... eee eee 189
Point of interest
refer to Online Points of Interest........ 189
Polishing. ... 0.0... 0.0 eee eee eee eee ee 269
Power closing (doors) ...............0000e 30
POWEN SOUNCESE. 5 secs «5 snes oo saute © ae 81,213
Power WINGOWS « swoiox © 2 cone v eave ee ren oo 40
Malfunction............0..0eee eee 40, 41
Power windows malfunction.............. 40
Predictive control..............00000005 133
Predictive messagesS...............-+05- 132
pre sense
refer to Audi presense................ 146
Presentation mode..............2--005- 201
Pressure
Tire pressure monitoring system........ 264
THES: = sews: & y weve 3 E Res FY OE cE eee Gg 256
Protecting.................0-00 222s eee 269
Pyrotechnic elements..............0005 292
Q
Quattro... 1. eee eee 111
Selective wheel torque control.......... 112
R
Radio: « sees ¢ seve 2 vets s Howe ss Hea Eee 202
Radio'textics «3 xcs 2 2 mean + owen es een « 205
Station list... 0.0.0.0... 2c eee eee eee 202
Radio communications equipment........ 294
Radioiequipmentice: «= warns x x cose v a amonwens 2 294
Radio Standards Specification (RSS) ....... 295
Raikearrier . osc ss sees y pangs s eee 2 ee 109
Rain/light sensor
Headlights........ 0... eee eee eee eee 45
Intermittent mode (windshield wipers) .... 53
R&tGSs = savnu = & eauns 4 & Savon 4 5 GER XS RoR a 14
Reading lights........... cee cece eee eee 50
Rear cross-traffic assist..........0.00005 163
Rear fog lights. ........... cece eee eee eee 45
Rear lid
refer to Luggage compartment lid........ 37
Rear lowering....... 0. eee c eee eee eee 84
RRAPISCAUS. « o snsccay 1 0 aienenm 0 sramese © oxetems oe ease 61
Rearviewscamerals = sess « © ensues © eames > o aes 158
Rear window defogger................00. 91
Rear wiper blades
Changing......... ee eee eee eee 55
Cleaning... ....... 0. cece eee eee eee 55
REAR (climate control system)............ 90
Reception range..................0-00- 202
RecinculationiMOde vcs « » smn « 6 siseee » 6 svees 91
RECUPEFATOM cas 6 i sowsice + vi seme Ww exienee wo antae 1s
Refuelingis « csesmne se veseive xo axaveue x x commas @ Ht one 230
Remote control
Garage door opener...........-...0005- 42
Remote:control-key « csccia e ccece se wesnte e 6 tease 34
Convenience opening and closing......... 4l
Key
replacement......... 00sec cere eee 34
LED swansea & ean 4 6 oma we wanes ae mime x ee 36
Replacing the battery..............0005 36
Unlocking and locking................-- 35
also.refer to Vehicle key’. «cscs 6s owen 6 © ws 34
Removing the caps (wheel bolts)......... 275
ROD@INS «scx & poae s + Qewy © ¥ seme yo See es 292
REPGatis « « eves 5 v some ¢ ees F Meee et ee 217
Replacement key.........-.....--0000005 34
Replacement parts...............00-005 294
Replacing bulbs.................0.2.00. 287
Replacing fuses...........0 0.0 e ee eee 283
Reporting Safety Defects................ 294
Rewinding (media files)................. 215
RIN’: « neee & eae 2 s ems & eS E WEEE SE 260
Cleaning. ......... 0. eee eee eee eee 269
Roadicanrien « ssccave a i svauwa v meus wo amen a 0 aa 109
Road noise compensation............... 225
Roof
refer to Panoramic glass roof............ 41
Roofiload « sxc s+ scvins ou amavis © wtatoas = Hc 298