2019 YAMAHA YFM700R Owners Manual

9-1
9
EBU25861
CLEANING AND STORAGE
EBU25882CleaningFrequent, thorough cleaning of your ATV will not
only enhance its appearance but will improve its
general performance and extend the useful life of
many components.1. Before cleaning the ATV: a. Block off the end of the exhaust pipe toprevent water entry. A plastic bag and
strong rubber band may be used.
b. Make sure the spark plug and all filler caps are properly installed.
2. If the engine case is excessively greasy, apply degreaser with a paint brush. Do not apply
degreaser to the wheel axles.
3. Rinse the dirt and degreaser off with a garden hose. Use only enough pressure to do the
job. WARNING! Wet brakes may have re-
duced stopping ability, increasing the
chance of an accident. Test the brakes af-
ter washing. Apply the brakes several
times at slow speeds to let friction dry out
the linings.
[EWB02312]
NOTICE: Excessive wa-
ter pressure may cause water seepage and deterioration of wheel bearings,
brakes, transmission seals and electrical
devices. Many expensive repair bills have
resulted from improper high-pressure de-
tergent applications such as those avail-
able in coin-operated car washers.
[ECB00712]
4. Once most of the dirt has been hosed off,
wash all surfaces with warm water and mild,
detergent-type soap. An old toothbrush or
bottle brush is handy for hard-to-reach plac-
es.
5. Rinse the ATV off immediately with clean wa- ter and dry all surfaces with a chamois, clean
towel or soft absorbing cloth.
6. Clean the seat with a vinyl upholstery cleaner to keep the cover pliable and glossy.
7. Automotive type wax may be applied to all painted and chrome plated surfaces. Avoid
combination cleaner-waxes. Many contain
abrasives which may mar the paint or protec-
tive finish. When finished cleaning, start the
engine and let it idle for several minutes.
UBB561E0.book Page 1 Monday, March 26, 2018 11:15 AM

9-2
9
EBU27264StorageShort-term
Always store your ATV in a cool, dry place and, if
necessary, protect it against dust with a porous
cover. NOTICE: Storing the ATV in a poorly ven-
tilated room or covering it with a tarp while it is
still wet, will allow water and humidity to seep
in and cause rust. To prevent corrosion, avoid
damp cellars, stables (because of the presence
of ammonia) and areas where strong chemi-
cals are stored.
[ECB00722]
Long-term
Before storing your ATV for several months: 1. Make any necessary repairs and perform all outstanding maintenance.
2. Follow all the instructions in the Cleaning sec- tion of this chapter.
3. Fill up the fuel tank and add fuel stabilizer (Fu- el Med Rx if available), and then run the en-
gine for 5 minutes to distribute the treated
fuel. 4. Perform the following steps to protect the en-
gine from internal corrosion.a. Remove the spark plug cap and spark plug.
b. Pour a teaspoonful of engine oil into the spark plug bore.
c. Install the spark plug cap onto the spark plug, and then place the spark plug on the
cylinder head so that the electrodes are
grounded. (This will limit sparking during
the next step.)
d. Turn the engine over several times with the starter. (This will coat the cylinder wall
with oil.)
e. Remove the spark plug cap from the spark plug, and then install the spark plug and
the spark plug cap.
5. Lubricate all control cables and the pivoting points of all levers and pedals.
6. Put the frame on stands or blocks to raise all wheels off the ground. (Alternatively, turn the
wheels each month to prevent the tires from
degrading in one spot.)
7. Cover the muffler outlet with a plastic bag to prevent moisture from entering it.
Specified amount:
7.5 ml per liter of fuel (1 oz per gallon)UBB561E0.book Page 2 Monday, March 26, 2018 11:15 AM

9-3
9
8. Remove the battery and fully charge it. (See
page 8-52.)
UBB561E0.book Page 3 Monday, March 26, 2018 11:15 AM

10-1
10
EBU25962
SPECIFICATIONS
Dimensions:Overall length:2035 mm (80.1 in)
Overall width: 1180 mm (46.5 in)
Overall height:
1160 mm (45.7 in)
Seat height: 856 mm (33.7 in)
Wheelbase: 1240 mm (48.8 in)
Ground clearance:
245 mm (9.6 in)
Minimum turning radius: 3.2 m (10.50 ft)
Maximum water depth: 35 cm (14 in)Weight:Curb weight:289.0 kg (637 lb) (YFM45KDHK, YFM45KDXK)
295.0 kg (650 lb) (YFM45KPHK, YFM45KPLK,
YFM45KPXK)Loading:Maximum loading limit:240.0 kg (530 lb)
(Total weight of rider, cargo, accessories, and tongue)
Noise and vibration level:Noise level (77/311/EEC):78.0 dB(A) at 3125 r/min (YFM45KDHK,
YFM45KDXK_EUR/FRA/GBR, YFM45KPHK,
YFM45KPLK, YFM45KPXK_EUR/FRA/GBR)
Uncertainty of measurement:
3.0 dB(A) (YFM45KDHK, YFM45KDXK_EUR/FRA/GBR,
YFM45KPHK, YFM45KPLK,
YFM45KPXK_EUR/FRA/GBR)
Vibration on seat (EN1032, ISO5008): Will not exceed 0.5 m/s² (YFM45KDHK,
YFM45KDXK_EUR/FRA/GBR, YFM45KPHK,
YFM45KPLK, YFM45KPXK_EUR/FRA/GBR)
Uncertainty of measurement: 0.0 m/s² (YFM45KDHK, YFM45KDXK_EUR/FRA/GBR,
YFM45KPHK, YFM45KPLK,
YFM45KPXK_EUR/FRA/GBR)
Vibration on handle (EN1032, ISO5008):
Will not exceed 2.5 m/s² (YFM45KDHK,
YFM45KDXK_EUR/FRA/GBR, YFM45KPHK,
YFM45KPLK, YFM45KPXK_EUR/FRA/GBR)
Uncertainty of measurement: 0.3 m/s² (YFM45KPHK, YFM45KPLK,
YFM45KPXK_EUR/FRA/GBR)
0.4 m/s² (YFM45KDHK, YFM45KDXK_EUR/FRA/GBR)Engine:Combustion cycle:4-stroke
UBB561E0.book Page 1 Monday, March 26, 2018 11:15 AM

10-2
10
Cooling system:Liquid cooled
Valve train: SOHC
Number of cylinders:
Single cylinder
Displacement: 421 cm³
Bore × stroke:
84.5 × 75.0 mm (3.33 × 2.95 in)
Compression ratio:
10.0 : 1
Starting system: Electric starter
Lubrication system: Wet sumpEngine oil:Recommended brand:YAMALUBE
SAE viscosity grades: 5W-30, 10W-30, 10W-40, 15W-40, 20W-40, 20W-50 Recommended engine oil grade:
API service SG type or higher, JASO standard MA
Quantity: Oil change:2.30 L (2.43 US qt, 2.02 Imp.qt)
With oil filter removal: 2.40 L (2.54 US qt, 2.11 Imp.qt)
Final gear oil:Type:Yamaha Friction Modified Shaft Drive Gear Oil
Quantity: 0.38 L (0.40 US qt, 0.33 Imp.qt)Differential gear oil:Type:Yamaha Friction Modified Shaft Drive Gear Oil or SAE 80
API GL-4 Hypoid gear oil
Quantity: 0.35 L (0.37 US qt, 0.31 Imp.qt)0 10 30 50 70 90 110 130 F
–20 –10 0 10 20 30 40 50 CSAE 5W-30
SAE 10W-30
SAE 10W-40
SAE 15W-40
SAE 20W-40SAE 20W-50
UBB561E0.book Page 2 Monday, March 26, 2018 11:15 AM

10-3
10
Coolant quantity:Radiator (including all routes):1.32 L (1.40 US qt, 1.16 Imp.qt)
Coolant reservoir (up to the maximum level mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)Air filter:Air filter element:Wet element
Air filter oil grade:
Foam air-filter oilFuel:Recommended fuel:Regular unleaded gasoline (Gasohol [E10] acceptable)
Minimum research octane:
91
Fuel tank capacity: 14 L (3.7 US gal, 3.1 Imp.gal)
Fuel reserve amount: 4.0 L (1.06 US gal, 0.88 Imp.gal)Throttle body:ID mark:BB51 00Spark plug (s):Manufacturer/model:
NGK/DR7EA
Spark plug gap: 0.6–0.7 mm (0.024–0.028 in)Drivetrain:Primary reduction ratio:
1.000 Secondary reduction ratio:
7.944 (39/24 x 24/18 x 33/9)
Final drive: Shaft
Clutch type:
Wet, centrifugal, shoe
Transmission type: CVT automatic with reverse
Gear ratio: Transmission ratio: 2.550–0.750 : 1
Reverse gear: 1.706 (29/17)
Low range:
2.813 (45/16)
High range: 1.652 (38/23)
Front tire:Size:
AT25 x 8-12
Manufacturer/model: CHENG SHIN/CU905Rear tire:Size:
AT25 x 10-12
Manufacturer/model: CHENG SHIN/CU906Tire air pressure (measured on cold tires):Recommended (For Oceania):
Front: 35.0 kPa (0.350 kgf/cm², 5.0 psi)
(YFM45KDXK_AUS/NZL, YFM45KPXK_AUS/NZL)
UBB561E0.book Page 3 Monday, March 26, 2018 11:15 AM

10-4
10
Rear:30.0 kPa (0.300 kgf/cm², 4.4 psi)
(YFM45KDXK_AUS/NZL, YFM45KPXK_AUS/NZL)
Minimum (For Oceania): Front:
32.0 kPa (0.320 kgf/cm², 4.6 psi)
(YFM45KDXK_AUS/NZL, YFM45KPXK_AUS/NZL)
Rear:
27.0 kPa (0.270 kgf/cm², 3.9 psi)
(YFM45KDXK_AUS/NZL, YFM45KPXK_AUS/NZL)
No cargo or trailer (For Europe):
Front:35.0 kPa (0.350 kgf/cm², 5.0 psi) (YFM45KDHK,
YFM45KDXK_EUR/FRA/GBR, YFM45KPHK,
YFM45KPLK, YFM45KPXK_EUR/FRA/GBR)
Rear: 30.0 kPa (0.300 kgf/cm², 4.4 psi) (YFM45KDHK,
YFM45KDXK_EUR/FRA/GBR, YFM45KPHK,
YFM45KPLK, YFM45KPXK_EUR/FRA/GBR)
With cargo or trailer (For Europe):
Front:50.0 kPa (0.500 kgf/cm², 7.3 psi) (YFM45KDHK,
YFM45KDXK_EUR/FRA/GBR, YFM45KPHK,
YFM45KPLK, YFM45KPXK_EUR/FRA/GBR)
Rear: 50.0 kPa (0.500 kgf/cm², 7.3 psi) (YFM45KDHK,
YFM45KDXK_EUR/FRA/GBR, YFM45KPHK,
YFM45KPLK, YFM45KPXK_EUR/FRA/GBR)
Front wheel:Rim size:12 x 6.0AT
Rear wheel:Rim size:12 x 7.5ATFront brake:Type:Hydraulic disc brakeRear brake:Type:
Mechanical wet multiple disc brakeBrake fluid:Specified brake fluid:DOT 4Front suspension:Type:Double wishbone
Spring: Coil spring
Shock absorber:
Gas-hydraulic damper
Wheel travel: 171 mm (6.8 in)Rear suspension:Type:
Double wishbone
Spring: Coil spring
Shock absorber: Gas-hydraulic damper
Wheel travel:
189 mm (7.4 in)
UBB561E0.book Page 4 Monday, March 26, 2018 11:15 AM

10-5
10
Electrical system:System voltage:12 V
Ignition system:
TCI
Charging system: AC magnetoBattery:Model:
YTX20L-BS
Voltage, capacity: 12 V, 18.0 AhLights:Headlight:
T19L, 30.0 W/30.0 W
Handlebar-mounted light: T15H, 35.0 W/36.5 W (YFM45KPHK, YFM45KPLK,
YFM45KPXK)
Brake/tail light: 21.0 W/5.0 W
Meter lighting: LED
Neutral indicator light:
LED
Reverse indicator light: LED
Coolant temperature warning light: LED
Parking brake indicator light:
LED
Four-wheel-drive indicator light: LED Engine trouble warning light:
LED
EPS warning light: LED (YFM45KPHK, YFM45KPLK, YFM45KPXK)
Fuses:Main fuse:40.0 A
Headlight fuse: 15.0 A
Signaling system fuse:
10.0 A
Ignition fuse: 10.0 A
Auxiliary DC jack fuse: 10.0 A
Fuel injection system fuse:
10.0 A
Four-wheel-drive motor fuse: 3.0 A
Radiator fan motor fuse: 20.0 A
EPS fuse:
40.0 A (YFM45KPHK, YFM45KPLK, YFM45KPXK)EBU30403Noise and vibration levels statement (for Eu-
rope)
The figures quoted are emission levels and are not
necessarily safe working levels. Whilst there is a
correlation between the emission and exposure
UBB561E0.book Page 5 Monday, March 26, 2018 11:15 AM