2019 YAMAHA YFM700R Owners Manual

8-44
8
Measure the brake pedal height and adjust if nec-
essary.
1. Remove the footboard by removing the quick fasteners, bolts, and nuts.
2. Loosen the locknut. 3. Turn the adjusting bolt in or out until the brake
pedal height is within the specified limits.
4. Tighten the locknut.
5. Install the footboard by installing the quick fasteners, bolts, and nuts, and then tighten
the bolts to the specified torques.
Brake pedal height:
80.0 mm (3.15 in)
1. Footboard
2. Quick fastener
3. Bolt and nut
4. Bolt
42
3
312
1. Locknut
2. Adjusting boltTightening torque:Locknut:7 N·m (0.7 kgf·m, 5.2 lb·ft)
2
1
UBB561E0.book Page 44 Monday, March 26, 2018 11:15 AM

8-45
8
TIPTighten the footboard bolts in the order shown. 1. Footboard bolt A
2. Footboard bolt B
3. Quick fastener
3
1
2
1
3
Tightening torques:Footboard bolt A:4.0 N·m (0.40 kgf·m, 3.0 lb·ft)
Footboard bolt B: 8 N·m (0.8 kgf·m, 5.9 lb·ft)
1
4
32
5
5
UBB561E0.book Page 45 Monday, March 26, 2018 11:15 AM

8-46
8
Adjusting the brake pedal free play
Measure the brake pedal free play and adjust if
necessary.
TIPThe brake lever free play and brake pedal height
must be adjusted before adjusting the brake pedal
free play. 1. Loosen the locknut.
2. To increase the brake pedal free play, turn the
brake pedal free play adjusting nut in direc-
tion (a). To decrease the brake pedal free
play, turn the adjusting nut in direction (b).
3. Tighten the locknut.
EBU24231Axle bootsThe axle boots must be checked for damage at
the intervals specified in the periodic maintenance
and lubrication chart. Check the axle boots for
tears or damage. If any damage is found, have
them replaced by a Yamaha dealer.
1. Brake pedal free playBrake pedal free play: 20.0 mm (0.79 in)
1
1. Brake pedal free play adjusting nut
2. Locknut
21
(a)
(b)
UBB561E0.book Page 46 Monday, March 26, 2018 11:15 AM

8-47
8
EBU29882Brake light switchesThe brake light, which is activated by the brake
pedal and brake levers, should come on just be-
fore braking takes effect.
The rear brake light switch for the brake pedal can
be adjusted as follows, but the other brake light
switches should be adjusted by a Yamaha dealer.
Turn the rear brake light switch adjusting nut while
holding the brake light switch in place. To make
the brake light come on earlier, turn the adjusting
nut in direction (a). To make the brake light come
on later, turn the adjusting nut in direction (b).
1. Front axle boot (each side)
1. Rear axle boot (each side)
1
1
1
1
1. Rear brake light switch
2. Rear brake light switch adjusting nut
12
(a)
(b)
UBB561E0.book Page 47 Monday, March 26, 2018 11:15 AM

8-48
8
EBU24905Checking and lubricating the cablesThe operation and the condition of all control ca-
bles should be checked before each ride, and the
cables and cable ends should be lubricated if nec-
essary. If a cable is damaged or does not move
smoothly, have a Yamaha dealer check or replace
it.
WARNING
EWB02582Inspect cables frequently and replace if
damaged. Corrosion can result when the ca-
ble sheaths become damaged, and cables
can also become frayed or kinked, which
could restrict the operation of controls and
lead to an accident or injury.
 Always make sure all control cables work
smoothly before you begin riding in cold
weather. If the control cables are frozen or do not work smoothly, you could be unable
to control the ATV, which could lead to an
accident or collision.
EBU28712Checking and lubricating the front and
rear brake leversThe operation of the front and rear brake levers
should be checked before each ride, and the lever
pivots should be lubricated if necessary.
Recommended lubricant:
Yamaha cable lubricant or other suitable cable lubricantRecommended lubricants: Front brake lever:Silicone grease
Rear brake lever: Lithium-soap-based grease
UBB561E0.book Page 48 Monday, March 26, 2018 11:15 AM

8-49
8Front brake lever
Rear brake lever
EBU28872Checking and lubricating the brake
pedalThe operation of the brake pedal should be
checked before each ride, and the pedal pivot
should be lubricated if necessary.EBU24964Checking the wheel hub bearingsThe front and rear wheel hub bearings must be
checked at the intervals specified in the periodic
maintenance and lubrication chart. If there is playRecommended lubricant:
Lithium-soap-based grease
UBB561E0.book Page 49 Monday, March 26, 2018 11:15 AM

8-50
8
in a wheel hub or if a wheel does not turn smooth-
ly, have a Yamaha dealer check the wheel hub
bearings.
EBU24974Lubricating the drive shaft universal
jointThe drive shaft universal joint must be lubricated
at the intervals specified in the periodic mainte-
nance chart.
TIPFor parts equipped with a grease nipple, use a
grease gun. EBU25023Checking the stabilizer bushesThe stabilizer bushes must be checked for cracks
or damage at the intervals specified in the periodic
maintenance and lubrication chart.
Have a Yamaha dealer replace the stabilizer bush-
es if necessary.
Recommended lubricant:
Lithium-soap-based grease1. Grease nipple
1
UBB561E0.book Page 50 Monday, March 26, 2018 11:15 AM

8-51
8
EBU25054Lubricating the rear knuckle pivotsThe rear knuckle pivots must be lubricated at the
intervals specified in the periodic maintenance
and lubrication chart.
TIPFor parts equipped with a grease nipple, use a
grease gun. EBU25095Lubricating the steering shaftThe steering shaft must be lubricated by a
Yamaha dealer at the intervals specified in the pe- riodic maintenance and lubrication chart.
Recommended lubricant:
Lithium-soap-based grease1. Grease nippleRecommended lubricant:Lithium-soap-based grease
1
1
UBB561E0.book Page 51 Monday, March 26, 2018 11:15 AM