2019 VOLKSWAGEN T-ROC 0A and 11

piece wheel bolts: use only two-piece wheel bolts.
Lifting the vehicle with the jack

Fig. 205 Jacking points.

Fig. 206 Jack fitted at the rear on the left-side of the vehicle.
First read and observe the introductoryinformation and safety warnings
The jack may be positioned only at the reinforcements on the underbody, which are located behind
the markings on the body Fig. 205
working on
Checklist
For your own safety, carry out the following points in the specified order

Choose a firm and level surface suitable for lifting the vehicle.

Switch off the engine. Select a gear on vehicles with a manual gearbox or move the selector lever to
position P on vehicles with DSG

Loosen the wheel bolts Wheel bolts.

Find the jacking point under the vehicle which is closest to the wheel that is being changed.

Insert the crank into the opening on the jack (depends on the vehicle equipment).

Crank up the jack until it just fits under the jacking point of the vehicle.

Ensure that the entire surface of the foot of the jack is resting securely on the floor, and that the
foot of the jack is positioned fully underneath the point of application and .

Position the jack and simultaneously continue to crank the claw up until it is in position around the
vertical rib underneath the vehicle .

Crank the jack further until the wheel is just clear of the ground.

WARNING
Incorrect use of the vehicle jack could cause the vehicle to slip off the jack. This could lead to severe
injuries. Observe the following points in order to reduce the risk of injuries:
jacks could slip out of position this includes vehicle jacks supplied with other Volkswagen models.
the vehicle to slip off the jack. If necessary, use a large, sturdy board or similar support for the
vehicle jack.

side member securely Fig. 206
lace any part of your body (e.g. an arm or leg) underneath the vehicle if the latter is
supported only by the vehicle jack.

cle when the engine is running, or if the vehicle is tilted to one side or on a
gradient.
cause the vehicle to fall off the vehicle jack.

WARNING
Ignoring any of the items on this important safety checklist can lead to accidents and severe injuries.

Changing a wheel

Fig. 207 Changing a wheel: removing the wheel bolts with the screwdriver handle.
First read and observe the introductoryinformation and safety warnings
Removing a wheel
Preparations for changing a wheel
Wheel bolts
Lifting the vehicle with the jack
Fig. 207
wheel bolts and place them on a clean surface.

Fitting the spare wheel or temporary spare wheel
y attention to the tyre direction of rotation Tyre lettering and tyre type

theft wheel bolt using the adapter at position Fig.
0

l the other wheel bolts in clockwise direction and tighten them slightly.

tighten the bolts in order but always in diagonally opposite sequence.
Hubcaps

WARNING
Incorrect tightening torque or incorrect use of wheel bolts can lead to a loss of control of the vehicle,
and cause accidents and serious injuries.
ep all wheel bolts and threads in the wheel hubs clean and free from oil and grease. The
wheel bolts must be easy to turn and be tightened to the specified torque.
not use
for loosening or tightening them.
After changing a wheel
First read and observe the introductoryinformation and safety warnings
luggage compartment Vehicle toolkit

Tightening torque of wheel
bolts
as possible.

After changing a wheel, the indicator lamp for the tyre monitoring system may indicate a fault in the
system T
Breakdown set
Introduction
This chapter contains information on the followingsubjects:
Contents of the breakdown set
Preparations
Sealing and inflating tyres

Check after driving for 10 minutes
The breakdown set can be used to temporarily and reliably seal any tyre damage caused by foreign
bodies or punctures (up to approx. 4 mm in diameter). Do not remove foreign objects (e.g. screws or
nails) from the tyre!
Once the sealant has been added to the tyre, the tyre pressure must be checked and adjusted again
after approximately 10 minutes of driving.
Seek expert assistance if more than one of the vehicle's tyres is damaged. The breakdown set is
designed to fill only one tyre.
Only use the breakdown set when the vehicle has been safely parked and you are familiar with the
work and safety precautions needed. Seek expert assistance if this is not the case.
The tyre sealant must not be used:

-20

hicle.
to the position P or select a gear on a manual gearbox in order to reduce the risk of unintended
vehicle movement.

WARNING
Tyres that have been filled with sealant will not handle in the same way as a standard tyre.
km/h (50 mph.

km/h (50 mph) and then check the tyre.

Dispose of used or out-of-date sealant in accordance with legal requirements.

A new tyre filler bottle can be obtained from a Volkswagen dealership.

Observe the separate instructions from the manufacturer of the breakdown set.
Contents of the breakdown set

Fig. 208 Illustration: components in the breakdown set

Fig. 209 Illustration: compressor from the breakdown set.
First read and observe the introductoryinformation and safety warnings
The breakdown set is located underneath the floor covering in the luggage compartment.
The breakdown set consists of the following components Fig. 208
Sticker with the maximum permitted speed max. 80 km/h or max. 50 mph
Filler hose with plug
Tyre filler bottle
Spare valve core
Valve core extractor
The compressor in the breakdown set consists of the following components Fig. 209
On/off switch
Air bleed screw
Tyre pressure display
Tyre filler hose
12-volt plug
Air compressor
There is a slot on the lower end of the valve core extractorFig. 208
applies to the spare valve core

set may be operated from the 12-volt socket, even if the
power rating on the type plate of the air compressor exceeds the maximum power rating of the
socket.
Preparations
First read and observe the introductoryinformation and safety warnings
Checklist
Always carry out the following actions in the given order

If your vehicle has a flat tyre, park the vehicle on a firm and level surface at a safe distance from
moving traffic.

Switch on the electronic parking brake Parking and manoeuvring.

DSG