2019 MERCEDES-BENZ SL CLASS brake
[x] Cancel search: brakePage 230 of 330
Display messagesPossible causes/consequences and P PSolutions
Tire Press. Moni‐Tire Press. Moni‐tor Currentlytor CurrentlyUnavailableUnavailable
Because there is interference from a strong source of radio waves,no signals from the tire pressure sensors are detected. The tirepressure monitor is temporarily malfunctioning.
XDrive on.The tire pressure monitor restarts automatically as soon as theproblem has been resolved.
TirePress. Sen‐TirePress. Sen‐sor(s) Missingsor(s) MissingThere is no signal from the tire pressure sensor of one or severalwheels. The pressure of the affected tire does not appear in themultifunction display.
XHave the faulty tire pressure sensor replaced at a qualified spe-cialist workshop.
Tire Pressure Moni‐Tire Pressure Moni‐tor Inoperative Notor Inoperative NoWheel SensorsWheel Sensors
The wheels mounted do not have a suitable tire pressure sensor.The tire pressure monitor is deactivated.
XMount wheels with suitable tire pressure sensors.The tire pressure monitor is activated automatically after drivingfor a few minutes.
Tire Press. Moni‐Tire Press. Moni‐tor Inoperativetor InoperativeThe tire pressure monitor is faulty.
XVisit a qualified specialist workshop.
Vehicle
Display messagesPossible causes/consequences and P PSolutions
Shift to 'P' orShift to 'P' or'N' to Start Engine'N' to Start EngineYou have attempted to start the engine with the transmission inposition ^or [.
XShift the transmission to position ]or \\.
Apply Brake toApply Brake toShift from 'P'Shift from 'P'You have attempted to shift the transmission to position [, ^or \\without depressing the brake pedal.
XDepress the brake pedal.
To Shift out of PTo Shift out of Por N, Depressor N, DepressBrake and SwitchBrake and Switchon Engineon Engine
You have attempted to shift the transmission out of position ]or \\into another transmission position with the engine switched off.
XDepress the brake pedal.
XStart the engine.
Driver's Door OpenDriver's Door Open& Transmission Not& Transmission Notin P Risk of Vehi‐in P Risk of Vehi‐cle Rolling Awaycle Rolling Away
The driver's door is not fully closed and the transmission is in posi-tion ^, \\or [.
A warning tone also sounds.
GWARNING
The vehicle may roll away.
There is a risk of an accident.
XWhen parking the vehicle, shift the transmission to position ].
228Displaymessages
On-b oard computer and displays
Page 231 of 330
Display messagesPossible causes/consequences and P PSolutions
Only Select ParkOnly Select Park(P) When Vehicle(P) When Vehicleis Stationaryis Stationary
The vehicle is moving.
XPull over and stop the vehicle safely as soon as possible, payingattention to road and traffic conditions.
XShift the transmission to position ].
Apply Brake toApply Brake toSelect RSelect RYou have attempted to shift from position [to position ^.
XDepress the brake pedal.
XShift the transmission to position ^.
Service RequiredService RequiredDo Not Shift GearsDo Not Shift GearsVisit DealerVisit Dealer
You cannot change the transmission position due to a malfunction.
A warning tone also sounds.
If transmission position [is selected:
XDrive to a qualified specialist workshop without shifting the trans-mission from position [.
If position ^, \\or ]is selected:
XNotify a qualified specialist workshop or breakdown service.
Reversing Not Pos‐Reversing Not Pos‐sible Servicesible ServiceRequiredRequired
You can no longer shift to transmission position ^due to a mal-function.
Transmission positions ], \\or [continue to be available.
A warning tone also sounds.
XVisit a qualified specialist workshop.
Transmission Mal‐Transmission Mal‐function Stopfunction StopA malfunction has occurred in the mechanical transmission compo-nents.
A warning tone also sounds. The transmission shifts automaticallyto position \\.
XPull over and stop the vehicle safely as soon as possible, payingattention to road and traffic conditions.
XShift the transmission to position ].
XSecure the vehicle against rolling away (Ypage 146).
XNotify a qualified specialist workshop or breakdown service.
Stop Vehicle LeaveStop Vehicle LeaveEngine RunningEngine RunningWait TransmissionWait TransmissionCoolingCooling
The transmission has overheated. Pulling away can be temporarilyimpaired or not possible.
XPull over and stop the vehicle safely as soon as possible, payingattention to road and traffic conditions. Do not continue drivingunder any circumstances.
XWait until the display message disappears before pulling away.
Auxiliary BatteryAuxiliary BatteryMalfunctionMalfunctionThe auxiliary battery for the automatic transmission is no longerbeing charged.
XVisit a qualified specialist workshop at the next opportunity.
XUntil then, always shift the transmission to position ]beforeyou switch off the engine.
XBefore leaving the vehicle, apply the electric parking brake.
Displaymessages229
On-b oard computer and displays
Z
Page 237 of 330
Safety systems
Warning/indicatorlamp
Q QSignal type
Possible causes/consequences and P PSolutions
' M Q '(USA only), M(Canada only): the red brake system warning lamp islit while the engine is running.
A warning tone also sounds.
GWARNING
The brake boosting effect is malfunctioning and the braking characteristics maybe affected.
There is a risk of an accident.
XPull over and stop the vehicle safely as soon as possible, paying attention toroad and traffic conditions. Do not continue driving under any circumstances.
XSecure the vehicle against rolling away (Ypage 146).
XConsult a qualified specialist workshop.
XObserve the additional display messages in the multifunction display.
' M Q '(USA only) or M(Canada only): the red brake system warning lampis lit while the engine is running. A warning tone also sounds.
GWARNING
There is not enough brake fluid in the brake fluid reservoir.
The braking effect may be impaired.
There is a risk of an accident.
XPull over and stop the vehicle safely as soon as possible, paying attention toroad and traffic conditions. Do not continue driving under any circumstances.
XSecure the vehicle against rolling away (Ypage 146).
XDo not add brake fluid. Adding more will not correct the malfunction.
XConsult a qualified specialist workshop.
XObserve the additional display messages in the multifunction display.
' QUSA only: the red brake system warning lamp is lit while the engine is run-ning. The multifunction display also shows a display message with the &symbol.
The brake pads/linings have reached their wear limit.
XVisit a qualified specialist workshop.
Warning and indicator lamps235
On-board computer and displays
Z
Page 238 of 330
Warning/indicatorlamp
Q QSignal type
Possible causes/consequences and P PSolutions
% QThe yellow ABS warning lamp is lit while the engine is running.
ABS (anti-lock braking system) is malfunctioning.
If there is an additional warning tone, the EBD (electronic brake force distribu-tion) is malfunctioning.
Other driving systems and driving safety systems may also malfunction.
GWARNING
The brake system continues to function normally, but without the functions lis-ted above. The front and rear wheels could therefore lock if you perform a fullbrake application, for example.
The steerability and braking characteristics may be severely affected. The brak-ing distance in an emergency braking situation can increase.
If ESP®is not operational, ESP®is unable to stabilize the vehicle.
There is an increased risk of skidding and an accident.
XObserve the additional display messages in the multifunction display.
XDrive on carefully.
XVisit a qualified specialist workshop immediately.
If the ABS control unit is defective, there is also a possibility that other systems,such as the navigation system or the automatic transmission, will not be availa-ble.
' M
Page 240 of 330
Warning/indicatorlamp
Q QSignal type
Possible causes/consequences and P PSolutions
t QMercedes-AMG vehicles only:
The yellow SPORT handling mode warning lamp is lit while the engine is running.
SPORT handling mode is activated.
GWARNING
When SPORT handling mode is switched on, ESP®is unable to stabilize the vehi-cle.
There is an increased risk of skidding and an accident.
XOnly switch to SPORT handling mode in accordance with the conditions
described in the "Activating/deactivating ESP®" section (Ypage 68).
I $ Q I(USA only), $(Canada only): the red indicator lamp for the electricparking brake flashes or is lit and/or the yellow warning lamp for the electricparking brake is lit.
XObserve the additional display messages in the multifunction display.
u QThe red restraint system warning lamp is lit while the engine is running.
The restraint system is malfunctioning.
GWARNING
The air bags or Emergency Tensioning Devices may either be triggered uninten-tionally or, in the event of an accident, may not be triggered.
There is an increased risk of injury.
XObserve the additional display messages in the multifunction display.
XDrive on carefully.
XContact a qualified specialist workshop and have the restraint systemchecked.
For further information about the restraint system, see (Ypage 41).
238Warning and indicator lamps
On-board computer and displays
Page 271 of 330
Make sure that windshield washer concen-
trate is not spilled in the vicinity of the filler
neck.
Example
XTo open:pull cap Cupwards by the tab.
XAdd the premixed washer fluid.
XTo close:press cap Conto the filler neckuntil it engages.
If the washer fluid level drops below the rec-ommended minimum fluid level of 1 US qt(1 liter), a message appears in the multifunc-tion display prompting you to add washer fluid(Ypage 231).
Further information on windshield washerfluid/antifreeze (Ypage 325).
Overview of the engine compart-
ment
Example engine
COil dipstick
DBrake fluid reservoir
Page 273 of 330
Rsolvents
Rcleaning agents containing solvents
Do not scrub.
Do not touch the surfaces and films withhard objects, e.g. rings or ice scrapers. Oth-erwise, you may scratch or damage the sur-faces and films.
!Do not park your vehicle for a long periodof time directly after cleaning, particularlyafter cleaning the wheel rim with wheelcleaner. Wheel cleaner can lead to theincreased corrosion of the brake discs andpads. Therefore, drive for a few minutesafter cleaning. By heating up the brakes, thebrake discs and pads dry. The vehicle canthen be parked for a long period of time.
Regular care of your vehicle is a condition forretaining the quality in the long term.
Use care products and cleaning agents recom-mended and approved by Mercedes-Benz.
Washing the vehicle and cleaning
the paintwork
Automatic car wash
GWARNING
Braking efficiency is reduced after washing
the vehicle. There is a risk of an accident.
After the vehicle has been washed, brake
carefully while paying attention to the traffic
conditions until full braking power is
restored.
!When DISTRONIC PLUS or the HOLD func-tion is activated, the vehicle brakes auto-matically in certain situations.
To avoid damage to the vehicle, deactivateDISTRONIC PLUS and the HOLD function inthe following or similar situations:
Rwhen towing the vehicle
Rin the car wash
!It is preferable to use car washes withadjustable high-pressure pre-cleaning thatcorresponds to the specification for theCabriolet program. In car washes that usehigh water pressures, there is a risk that asmall amount of water may leak into thevehicle.
!Vehicles with HANDS-FREE ACCESS: if aSmartKey with KEYLESS-GO is within thedetection range of the KEYLESS-GOantenna, the following situations could leadto the unintentional opening of the trunk lid:
Rusing a car wash
Rusing a power washer
Make sure that the SmartKey is at least6.5 ft (2 m) away from the vehicle.
!Never clean your vehicle in a TouchlessAutomatic Car Wash as these use specialcleaning agents. These cleaning agents candamage the paintwork or plastic parts.
If you have your vehicle cleaned in a high-pressure automatic car wash, smallamounts of water may enter the vehicle.
!Make sure that the automatic transmissionis in positionNwhen washing your vehiclein a tow-through car wash. The vehicle couldbe damaged if the transmission is in anotherposition.
!Make sure that:
Rthe side windows and the roof are com-pletely closed
Rthe climate control blower is switched off
Rthe windshield wiper switch is at position0
The vehicle could otherwise be damaged.
You can clean the vehicle at an automatic carwash from the very start.
Preferably clean the vehicle at automatic carwashes that use textile washing elementswithout brushes. This prevents fine scratchesfrom forming on the paintwork and film.
If the vehicle is very dirty, pre-wash it beforecleaning it in an automatic car wash.
After using an automatic car wash, wipe offwax from the windshield and the wiper blades.This will prevent smears and reduce wipingnoises caused by residue on the windshield.
iVehicles with decorative film: select awash program without hot wax at the auto-matic car wash.
Washing by hand
In some countries, washing by hand is onlyallowed at specially equipped washing bays.
Care271
Maintenance and care
Z
Page 274 of 330
Observe the legal requirements in each coun-try.
XDo not use hot water and do not wash thevehicle in direct sunlight.
XUse a soft sponge to clean.
XUse a mild cleaning agent, such as a carshampoo approved by Mercedes-Benz.
XThoroughly hose down the vehicle with agentle jet of water.
XDo not point the water jet directly towardsthe air inlet or the edges of decorative foils.
XUse plenty of water and rinse out thesponge frequently.
XRinse the vehicle with clean water and drythoroughly with a chamois.
XDo not let the cleaning agent dry on thepaintwork or the decorative foils.
Carefully remove all deposits of road salt assoon as possible when driving in winter.
Power washers
GWARNING
The water jet from a circular jet nozzle (dirt
blasters) can cause invisible exterior dam-
age to the tires or chassis components.
Components damaged in this way may fail
unexpectedly. There is a risk of an accident.
Do not use power washers with circular jet
nozzles to clean the vehicle. Have damaged
tires or chassis components replaced imme-
diately.
!Vehicles with decorative film: parts of yourvehicle are covered with decorative film.Maintain a distance of at least 27.5 in(70 cm) between the film-covered parts ofthe vehicle and the nozzle of the powerwasher.
Information about the correct distance isavailable from the equipment manufacturer.
Move the power washer nozzle around whencleaning your vehicle.
The water temperature of the power washermust not exceed 140 ‡ (60 †).
!Always maintain a distance of at least12 in (30 cm) between the vehicle and thepower washer nozzle. Information about thecorrect distance is available from the equip-ment manufacturer.
Move the power washer nozzle around whencleaning your vehicle.
Do not aim directly at any of the following:
RTires
RDoor gaps, roof gaps, joints, etc.
RElectrical components
RBattery
RPlug-type couplings
RLight bulbs
RSeals
RTrim elements
RVentilation slots
Damaged seals or electrical componentscan lead to leaks or failures.
!Vehicles with HANDS-FREE ACCESS: if aSmartKey with KEYLESS-GO is within thedetection range of the KEYLESS-GOantenna, the following situations could leadto the unintentional opening of the trunk lid:
Rusing a car wash
Rusing a power washer
Make sure that the SmartKey is at least6.5 ft (2 m) away from the vehicle.
Cleaning the paintwork
!Do not affix:
Rstickers
Rfilms
Rmagnetic plates or similar items
to painted surfaces. You could otherwisedamage the paintwork.
Scratches, corrosive deposits, areas affectedby corrosion and damage caused by inade-quate care cannot always be completelyrepaired. In such cases, visit a qualified spe-cialist workshop.
XRemove dirt immediately, where possible,while avoiding rubbing too hard.
XSoak insect remains with insect removerand rinse off the treated areas afterwards.
XSoak bird droppings with water and rinse offthe treated areas afterwards.
XRemove tree resin, oils, fuels and greases byrubbing gently with a cloth soaked in petro-leum ether or lighter fluid
XRemove coolant and brake fluid with a moistcloth and clear water.
272Care
Maintenance and care