2019 MAZDA MODEL CX-30 lock

Ignition Switch
▼Push Button Start Positions
The system operates only when the key
is within operational range.
Each time the push button start is
pressed, the ignition switches in the
order of
off, ACC, and ON. Pressing
the push button start again from ON
switches the ignition
off.
1. Indicator light
2. Push button start
NOTE
xThe engine starts by pressing the
push button start while depressing
the clutch pedal (manual
transmission) or the brake pedal
(automatic transmission). To switch
the ignition position, press the push
button start without depressing the
pedal.
xDo not leave the ignition switched
ON while the engine is not running.
Doing so could result in the battery
going dead. If the ignition is left in
ACC (For automatic transmission,
the selector lever is in the P position,
and the ignition is in ACC), the
ignition switches off automatically
after about 25 minutes.
Off
The power supply to electrical devices
turns off and the indicator light
(amber) also turns off.
In this position the steering wheel is
locked.
WARNING
Before leaving the driver's seat,
always switch the ignition off, set the
parking brake, and make sure the
selector lever is in P (automatic
transmission) position or in 1st gear
or R (manual transmission):
Leaving the driver's seat without
switching the ignition off, setting the
parking brake, and shifting the selector
lever to P (automatic transmission)
position or to 1st gear or R (manual
transmission) is dangerous.
Unexpected vehicle movement could
occur which could result in an
accident.
In addition, if your intention is to leave
the vehicle for even a short period, it is
important to switch the ignition
off, as
leaving it in another position will
disable some of the vehicle's security
systems and run the battery down.
NOTE
(Locked steering wheel)
If the push button start indicator light
(green) is
flashing , a message is
displayed on the multi-information,
and the beep sound is heard, this
indicates that the steering wheel is not
unlocked. To unlock the steering
wheel, press the push button start
while moving the steering wheel left
and right.
When Driving
Start/Stop Engine
4-4

ACC (Accessory)
Some electrical accessories will
operate and the indicator light (amber)
illuminates.
In this position the steering wheel is
unlocked.
NOTE
The keyless entry system does not
function while the push button start
has been pressed to ACC, and the
doors will not lock/unlock even if they
have been locked manually.
ON
This is the normal running position
after the engine is started. The
indicator light (amber) turns off. (The
indicator light (amber) illuminates
when the ignition is switched ON and
the engine is not running.)
Some indicator lights/warning lights
should be inspected before the engine
is started.
Refer to Warning/Indicator Lights on
page 4-32.
Refer to Indication/Indicator Lights on
page 4-34.
NOTE
(SKYACTIV-G 2.0, SKYACTIV-G 2.5,
SKYACTIV-X 2.0)
When the push button start is pressed
to ON, the sound of the fuel pump
motor operating near the fuel tank can
be heard. This does not indicate an
abnormality.
Starting the Engine
▼Starting the Engine
WARNING
Radio waves from the key may affect
medical devices such as pacemakers:
Before using the key near people who
use medical devices, ask the medical
device manufacturer or your physician
if radio waves from the key will affect
the device.
NOTE
xThe key must be carried because the
key carries an immobilizer chip that
must communicate with the engine
controls at short range.
xThe engine can be started when the
push button start is pressed from off,
ACC, or ON.
xThe push button start system
functions (function which can start
the engine by only carrying the key)
can be deactivated to prevent any
possible adverse effect on a user
wearing a pacemaker or other
medical device. If the system is
deactivated, you will be unable to
start the engine by carrying the key.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) for details. If the push
button start system functions have
been deactivated, you can start the
engine by following the procedure
indicated when the key battery goes
dead.
Refer to Engine Start Function When
Key Battery is Dead on page 4-8.
xAfter starting a cold engine, the
engine speed increases and a
whining sound from the engine
compartment can be heard.
When Driving
Start/Stop Engine
4-5

Automatic Transmission
Controls
▼Automatic Transmission Controls
1. Lock-release button
2. Selector lever

Indication Various Lockouts
Indicates that you must depress
the brake pedal and hold in the
lock-release button to shift (The ig-
nition must be switched ON).
Indicates the selector lever can be
shifted freely into any position.
Indicates that you must hold in the
lock-release button to shift.
NOTE
The Sport AT has an option that is not
included in the traditional automatic
transmission that gives the driver the
option of selecting each gear instead of
leaving it to the transmission to shift
gears. Even if you intend to use the
automatic transmission functions as a
traditional automatic, you should also
be aware that you can inadvertently
shift into manual shift mode and an
inappropriate gear may be retained as
the vehicle speed increases. If you
notice the engine speed going higher
or hear the engine racing, confirm you
have not accidentally slipped into
manual shift mode (page 4-46).
When Driving
Automatic Transmission
4-43

Shift-Lock System
▼Shift-Lock System
The shift-lock system prevents shifting
out of P unless the brake pedal is
depressed.

To shift from
P:
1. Depress and hold the brake pedal.
2. Start the engine.
3. Press and hold the lock-release
button.
4. Move the selector lever.
NOTE
xWhen the ignition is switched to
ACC or the ignition is switched
off,
the selector lever cannot be shifted
from P position.
xThe ignition cannot be switched to
OFF if the selector lever is not in P
position.
▼Shift-Lock Override
If the selector lever will not move from
P position using the proper shift
procedure, continue to hold down the
brake pedal.
Ty p e A
1. Remove the shift-lock override
cover using a cloth-wrapped
flat
head screwdriver.
2. Insert a flat screwdriver and push it
down.

1. Cover

3. Press and hold the lock-release
button.
4. Move the selector lever.
Take the vehicle to an expert repairer
(we recommend an Authorised Mazda
Repairer) to have the system checked.
Ty p e B
1. Press the lock-release button with
the button pressed.

1. Button

2. Move the selector lever.
Take the vehicle to an expert repairer
(we recommend an Authorised Mazda
Repairer) to have the system checked.
When Driving
Automatic Transmission
4-44

Transmission Ranges
▼Transmission Ranges
xThe shift position indication in the
instrument cluster illuminates.
Refer to Shift Position Indication on
page 4-46.
xShift the selector lever to the P or N
position to start the engine.
P (Park)
P locks the transmission and prevents
the front wheels from rotating.
WARNING
Always set the selector lever to P
position and set the parking brake:
Only setting the selector lever to the P
position without using the parking
brake to hold the vehicle is dangerous.
If P fails to hold, the vehicle could
move and cause an accident.
CAUTION
¾Shifting into P, N or R while the
vehicle is moving can damage your
transmission.
¾Shifting into a driving gear or reverse
when the engine is running faster
than idle can damage the
transmission.
R (Reverse)
In position R, the vehicle moves only
backward. You must be at a complete
stop before shifting to or from R,
except under rare circumstances as
explained in Rocking the Vehicle (page
3-56).
N (Neutral)
In N, the wheels and transmission are
not locked. The vehicle will roll freely
even on the slightest incline unless the
parking brake or brakes are on.
WARNING
If the engine is running faster than
idle, do not shift from N or P into a
driving gear:
It's dangerous to shift from N or P into
a driving gear when the engine is
running faster than idle. If this is done,
the vehicle could move suddenly,
causing an accident or serious injury.
Do not shift into N when driving the
vehicle:
Shifting into N while driving is
dangerous. Engine braking cannot be
applied when decelerating which
could lead to an accident or serious
injury.
CAUTION
Do not shift into N when driving the
vehicle. Doing so can cause
transmission damage.
NOTE
Apply the parking brake or depress the
brake pedal before moving the selector
lever from N position to prevent the
vehicle from moving unexpectedly.
D (Drive)
D is the normal driving position. From
a stop, the transmission will
automatically shift through a 6-gear
sequence.
M (Manual)
M is the manual shift mode position.
Gears can be shifted up or down by
operating the selector lever.
Refer to Manual Shift Mode on page
4-46.
When Driving
Automatic Transmission
4-45

▼Headlight High-Low Beam
The headlights switch between high
and low beams by moving the lever
forward or backward.

1. High beam
2. Low beam

When the headlight high-beams are
on, the headlight high-beam indicator
light is turned on.

▼Flashing the Headlights
The headlights can be flashed with the
ignition switched to ON.
To flash the headlights, pull the lever
fully towards you (the headlight switch
does not need to be on).

1. OFF
2. Headlight flashing

The headlight high-beam indicator
light in the instrument cluster
illuminates simultaneously. The lever
will return to the normal position when
released.

▼Coming Home Light
The coming home light turns on the
headlights (low beams) when the lever
is operated.
To turn on the lights
When the lever is pulled with the
ignition switched to ACC or OFF, the
low beam headlights turn on.
The headlights turn off after a certain
period of time has elapsed after all of
the doors are closed.
NOTE
xThe time until the headlights turn off
after all of the doors are closed can
be changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
xIf no operations are done for 3
minutes after the lever is pulled, the
headlights turn off.
xThe headlights turn off if the lever is
pulled again while the headlights are
illuminated.
▼Leaving Home Light
The leaving home light turns on the
lights when the transmitter unlock
button is pressed while away from the
vehicle.
When Driving
Switches and Controls
4-57

The following lights turn on when the
leaving home light is operated.
Low beams, Position lights, Tail lights,
Number plate lights.
To turn on the lights
When the ignition switch and the
headlight switch are in the following
conditions, the headlights will
illuminate when the transmitter unlock
button is pressed and the vehicle
receives the transmitter signal. The
headlights turn off after a certain
period of time has elapsed (30
seconds).
xIgnition switch: off
xHeadlight switch: AUTO, , or
1. Lock button
2. Unlock button
NOTE
xOperation of the leaving home light
can be turned on or
off.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
xWhen the transmitter lock button is
pressed and the vehicle receives the
transmitter signal, the headlights turn
off.
xWhen the headlight switch is turned
to the OFF position, the headlights
turn off.
▼Headlight Levelling
The number of passengers and weight
of cargo in the luggage Compartment
change the angle of the headlights.
The angle of the headlights will be
automatically adjusted when turning
on the headlights.
A system malfunction or operation
conditions are indicated by a warning.
Refer to Exterior Light Warning
Indication/Warning Light on page
7-58.
▼Running Lights*
Some countries require moving
vehicles to have their lights on (running
lights) during the daytime.

The running lights turn on or off
automatically.

NOTE
(Except countries prohibited by law)
The running lights can be deactivated.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
When Driving
Switches and Controls
4-58*Some models.

Windscreen Wipers and
Washer
▼Windscreen Wipers and Washer
The ignition must be switched ON to
use the wipers.
WARNING
Use only windscreen washer
fluid or
plain water in the reservoir:
Using radiator antifreeze as washer
fluid is dangerous. If sprayed on the
windscreen, it will dirty the
windscreen, affect your visibility, and
could result in an accident.
Only use windscreen washer
fluid
mixed with anti-freeze protection in
freezing weather conditions:
Using windscreen washer fluid without
anti-freeze protection in freezing
weather conditions is dangerous as it
could freeze on the windscreen and
block your vision which could cause an
accident. In addition, make sure the
windscreen is sufficiently warmed
using the defroster before spraying the
washer fluid.
NOTE
If the windscreen wipers are operated
under cold weather conditions or
during snowfall, they could stop due to
accumulated snow on the windscreen.
If the windscreen wipers stop due to
accumulated snow on the windscreen,
park the vehicle in a safe place, turn
the wiper switch off, and then remove
the accumulated snow. If the wiper
switch is turned to another position
other than OFF, the wipers will
operate. If the wipers do not operate
even though the wiper switch is turned
to a position other than OFF, consult
an expert repairer (we recommend an
Authorised Mazda Repairer) as soon as
possible.
▼Windscreen Wipers
Turn the wipers on by pressing the
lever up or down.
With intermittent wiper
Switch Posi-
tionWiper operation
Operation while pulling up
lever
OFF Stop
Intermittent
Low speed
When Driving
Switches and Controls
4-61