2019 MAZDA MODEL CX-30 light

Signal Indicator Refer to
(Green)
*Mazda Radar Cruise Control (MRCC) Set Indication4-134
*Mazda Radar Cruise Control with Stop & Go function (MRCC with
Stop & Go function) Set Indication4-143
*Cruising &
Tra ffi c Support (CTS) Set Indication4-154
*Smart Brake Support (SBS) OFF Indicator Light*1
Smart Brake
Support (SBS)
4-177
Smart Brake
Support [Rear]
(SBS-R)
4-180
Smart Brake
Support [Rear
Crossing]
(SBS-RC)
4-184
(White)
*Intelligent Speed Assistance (ISA) Standby Indication4-171
*Adjustable Speed Limiter (ASL) Standby Indication4-167
(Green)
*Intelligent Speed Assistance (ISA) Set Indication4-171
*Adjustable Speed Limiter (ASL) Set Indication4-167
(White)
*Cruise Standby Indication4-228
(Green)
*Cruise Set Indication4-228
*1 The light turns on when the ignition is switched on for an operation check, and
turns off a few seconds later or when the engine is started. If the light does not
turn on or remains turned on, have the vehicle inspected at an expert repairer
(we recommend an Authorised Mazda Repairer).
*2 The light turns on continuously when the parking brake is applied.
▼Wrench Indication/Indicator LightThe wrench indication/indicator light
is displayed/turns on under the
following conditions.
xWhen the preset maintenance
period has arrived.
When Driving
Instrument Cluster and Display
*Some models.4-37

Refer to the Information section in
the Mazda Connect Owner's
Manual.
CAUTION
¾When the maintenance period
arrives, have your vehicle inspected
by an expert repairer (we
recommend an Authorised Mazda
Repairer) as soon as possible. If
maintenance is neglected, a
decrease in vehicle performance
may occur which could cause
damage. Have your vehicle
inspected before the maintenance
period arrives.
¾If the vehicle continues to be
driven after the engine oil
replacement period has passed, it
could cause damage to the engine.
Replace the engine oil before the
maintenance period arrives.
¾(SKYACTIV-D 1.8)
Depending on the vehicle use
conditions, engine oil replacement
is required due to engine oil
deterioration from fuel penetrating
the engine oil. If “Excessive Oil
Level. Have the Vehicle Inspected”
is displayed on the
multi-information display in the
instrument cluster, have your
vehicle inspected at an expert
repairer (we recommend an
Authorised Mazda Repairer).
x(SKYACTIV-D 1.8)
xWhen fuel filter (sedimentor)
draining is required. Consult an
expert repairer (we recommend an
Authorised Mazda Repairer).
NOTE
xThe wrench indication/indicator
light may display/turn on earlier than
the preset period depending on
vehicle usage conditions.
xWhenever the engine oil is replaced,
a reset of the vehicle engine control
unit is necessary.
Refer to the Information section in
the Mazda Connect Owner's
Manual.

▼Glow Indicator Light (SKYACTIV-D
1.8)
When the ignition is switched ON, the
glow indicator light turns on. The glow
indicator light turns
off when
preheating is finished.

A problem in the system might be
indicated under the following
conditions. Have your vehicle
inspected by an expert repairer (we
recommend an Authorised Mazda
Repairer).
xThe glow indicator light does not
turn on when the ignition is switched
ON or it remains on.
xThe glow indicator light is flashing.
NOTE
If the vehicle is left with the ignition
switched ON without starting the
engine and a long period of time has
elapsed since preheating
finished, the
preheating may be performed again
and the glow indicator light may turn
on.
When Driving
Instrument Cluster and Display
4-38

Active Driving Display
▼Active Driving Display
1. Display
2. Dust-proof sheet
WARNING
Always adjust the display brightness and position with the vehicle stopped:
Adjusting the display brightness and position while driving the vehicle is dangerous
as doing so could distract your attention from the road ahead and lead to an
accident.
CAUTION
¾Do not place beverages near the dust-proof sheet of the active driving display. If
water or other liquids are splashed on the dust-proof sheet, it could cause
damage.
¾Do not place objects or apply stickers above the active driving display or to the
dust-proof sheet as they will cause interference.
NOTE
xWearing polarized sunglasses will reduce the visibility of the active driving display
due to the characteristics of the display.
xIf the battery has been removed and re-installed or the battery voltage is low, the
adjusted position may deviate.
xThe display may be difficult to view or temporarily affected by weather conditions
such as rain, snow, light, and temperature.
xIf the audio system is removed, the active driving display cannot be operated.
The active driving display indicates the following information:
xLane Departure Warning System (LDWS) Warnings
When Driving
Instrument Cluster and Display
4-39

Transmission Ranges
▼Transmission Ranges
xThe shift position indication in the
instrument cluster illuminates.
Refer to Shift Position Indication on
page 4-46.
xShift the selector lever to the P or N
position to start the engine.
P (Park)
P locks the transmission and prevents
the front wheels from rotating.
WARNING
Always set the selector lever to P
position and set the parking brake:
Only setting the selector lever to the P
position without using the parking
brake to hold the vehicle is dangerous.
If P fails to hold, the vehicle could
move and cause an accident.
CAUTION
¾Shifting into P, N or R while the
vehicle is moving can damage your
transmission.
¾Shifting into a driving gear or reverse
when the engine is running faster
than idle can damage the
transmission.
R (Reverse)
In position R, the vehicle moves only
backward. You must be at a complete
stop before shifting to or from R,
except under rare circumstances as
explained in Rocking the Vehicle (page
3-56).
N (Neutral)
In N, the wheels and transmission are
not locked. The vehicle will roll freely
even on the slightest incline unless the
parking brake or brakes are on.
WARNING
If the engine is running faster than
idle, do not shift from N or P into a
driving gear:
It's dangerous to shift from N or P into
a driving gear when the engine is
running faster than idle. If this is done,
the vehicle could move suddenly,
causing an accident or serious injury.
Do not shift into N when driving the
vehicle:
Shifting into N while driving is
dangerous. Engine braking cannot be
applied when decelerating which
could lead to an accident or serious
injury.
CAUTION
Do not shift into N when driving the
vehicle. Doing so can cause
transmission damage.
NOTE
Apply the parking brake or depress the
brake pedal before moving the selector
lever from N position to prevent the
vehicle from moving unexpectedly.
D (Drive)
D is the normal driving position. From
a stop, the transmission will
automatically shift through a 6-gear
sequence.
M (Manual)
M is the manual shift mode position.
Gears can be shifted up or down by
operating the selector lever.
Refer to Manual Shift Mode on page
4-46.
When Driving
Automatic Transmission
4-45

Driving Tips
▼Driving Tips
WARNING
Do not let the vehicle move in a
direction opposite to the direction
selected by the selector lever:
Do not let the vehicle move backward
with the selector lever in a forward
position, or do not let the vehicle
move forward with the selector lever in
the reverse position. Otherwise, the
engine may stop, causing the loss of
the power brake and power steering
functions, and make it difficult to
control the vehicle which could result
in an accident.
Passing
For extra power when passing another
vehicle or climbing steep grades,
depress the accelerator fully. The
transmission will shift to a lower gear,
depending on vehicle speed.
NOTE
xThe accelerator pedal may initially
feel heavy as it is being depressed,
then feel lighter as it is depressed
further. This change in pedal force
aids the engine control system in
determining how much the
accelerator pedal has been
depressed for performing kickdown,
and functions to control whether or
not kickdown should be performed.
xWhile the selector lever is in the M
position and the TCS is turned off,
manual shift mode does not switch
to automatic shift mode even if the
accelerator pedal is completely
depressed. Operate the selector
lever.
Climbing steep grades from a stop
To climb a steep grade from a stopped
position:
1. Depress the brake pedal.
2. Shift to D or M1, depending on the
load weight and grade steepness.
3. Release the brake pedal while
gradually accelerating.
Descending steep grades
When descending a steep grade, shift
to lower gears, depending on load
weight and grade steepness. Descend
slowly, using the brakes only
occasionally to prevent them from
overheating.
When Driving
Automatic Transmission
4-53

Lighting Control
▼Headlights
Turn the headlight switch to turn the headlights and other exterior lights on or off.
When the tail lights, position lights, and the number plate lights are turned on, the
lights-on indicator light in the instrument cluster turns on.

NOTE
xTo prevent discharging the battery, do not leave the lights on while the engine is
off unless safety requires them.
xHeadlights do not blind drivers approaching in the opposite direction no matter
what side of the road you must drive your vehicle (left-hand or right-hand traffic).
Therefore, it is not necessary to adjust the optical axis of the headlights when
switching temporarily to driving on the opposite side of the road (left-hand or
right-hand traffic).
Without auto-light control
Ignition Position ACC or OFF ON
Switch Position OFF
OFF
Headlights Off Off Off Off Off On
Running lights
*Off Off Off
On*1On*1*2Off
Tail lights
Position lights
Number plate
lightsOffOn
Off OffOn On
When Driving
Switches and Controls
4-54*Some models.

*1 When the light switch is switched to a
different position from the OFF, position while the
vehicle is stopped, the running lights turn off. When starting to drive the vehicle, the running lights
turn on again.
*2 When the light switch is switched to the OFF position, and then to the position again, the
running lights turn off directly after starting the engine. The running lights turn on when you begin
driving the vehicle.
With auto-light control
Ignition Position ACC or OFF ON
Switch Position
OFF
*1AUTOOFF*1AUTO
Headlights Off Off Off Off
Auto
*2*4Auto*3*4
On
Running lights
*Off Off Off Off Off
Ta i l l i g h t s
Po s i t i o n l i g h t s
Number plate
lightsOff Off On Off On
*1 The light switch returns to the AUTO position automatically.*2 During the daytime, the running lights turn on automatically. During the nighttime, the headlights,
position lights, tail lights, and the number plate lights turn on automatically.
*3 During the daytime, the running lights, position lights, tail lights, and the number plate lights turn on
automatically. During the nighttime, the headlights, position lights, tail lights, and the number plate
lights turn on automatically.
*4 When the light switch is switched to the OFF position while the vehicle is stopped, all of the lights
that are turned on turn off. When the light switch is switched from a position other than
to the
position while the vehicle is stopped, the running lights or the headlights turn off. When
starting to drive the vehicle, the lights that are turned
off turn on again.
NOTE
The running lights can be disabled using the personalisation features (page 4-58).
When Driving
Switches and Controls
*Some models.4-55

Auto-light control*
When the headlight switch is in a position other than and the ignition is
switched ON, the light sensor senses the surrounding lightness or darkness and
automatically turns the headlights and other exterior lights on or off.
CAUTION
¾Do not shade the light sensor by adhering a sticker or a label on the windscreen.
Otherwise the light sensor will not operate correctly.
¾The light sensor also works as a rain sensor for the auto-wiper control. Keep hands
and scrapers clear of the windscreen when the wiper lever is in the AUTO position
and the ignition is switched ON as fingers could be pinched or the wipers and
wiper blades could be damaged when the wipers activate automatically. If you are
going to clean the windscreen, be sure the wipers are turned
off completely when
it is particularly tempting to leave the engine running. This is particularly important
when clearing ice and snow.
NOTE
xThe headlights and other exterior lights may not turn off immediately even if the
surrounding area becomes well-lit because the light sensor determines that it is
night time if the surrounding area is continuously dark for several minutes such as
inside long tunnels, traffic jams inside tunnels, or in indoor parking lots.
xThe sensitivity of the auto-light control may be changed.
Refer to the Settings section in the Mazda Connect Owner's Manual.
When Driving
Switches and Controls
4-56*Some models.