2019 MAZDA MODEL CX-30 Wheel

Display/Icon Content
(4) Projected vehicle path distance
guide lines (yellow & red)These guide lines indicate the approximate distance to a
point measured from the rear of the vehicle (from the
end of the bumper).
xThe red line indicates the point about 0.5 m (19 in)
from the rear end of the bumper.
xThe yellow lines indicate the points about 1.0 m (39
in) and 2.0 m (78 in) from the rear end of the bumper.
NOTE
The setting can be changed so that the projected vehicle path lines are not
displayed.
Refer to the Settings section in the Mazda Connect Owner's Manual.
How to use the projected vehicle path line function
CAUTION
¾The front of the vehicle swings out wide when turning the steering wheel while
reversing. Maintain sufficient distance between the vehicle and an obstruction.
¾The parking sensor detection range has limitations. For example, obstructions
closing in from the side and objects short in height may not be detected. Always
confirm the safety around the vehicle visually when driving.
For details, refer to the parking sensor obstruction detection indication and
warning sound.
Refer to Parking Sensor System on page 4-252.
NOTE
xBecause there might be a difference between the image displayed on the screen,
such as indicated in the following , and the actual conditions when parking, always
check the safety at the rear of the vehicle and the surrounding area directly with
your eyes.
xEven though the back end of the parking space (or garage) displayed on the
screen and distance guide lines appear parallel, they may not actually be
parallel.
xWhen parking in a space with a division line on only one side of the parking
space, even though the division line and the vehicle width guide line appear
parallel, they may not actually be parallel.
xThe following shows an example of vehicle parking with the steering wheel turned
to the left while backing up the vehicle. When backing into a parking space from
the opposite direction, the steering operation is reversed.
When Driving
i-ACTIVSENSE
4-205

1. Back the vehicle into the parking space by turning the steering wheel so that the
vehicle enters the centre of the parking space.

1. (Screen display)
2. (Actual condition)
2. After the vehicle starts entering the parking space, stop and adjust the steering
wheel so that the distance between the vehicle width lines and the sides of the
parking space on the left and right are roughly equal, and then continue backing
up slowly.
3. Once the vehicle width lines and the sides of the parking space on the left and
right are parallel, straighten the wheels and back the vehicle slowly into the
parking space. Continue checking the vehicle's surroundings and then stop the
When Driving
i-ACTIVSENSE
4-206

¾Always keep the windscreen glass
around the camera clean by
removing dirt or fogging. Use the
windscreen defroster to remove
fogging on the windscreen.
¾Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) regarding cleaning the
interior side of the windscreen
around the Forward Sensing
Camera (FSC).
¾Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) before performing
repairs around the Forward Sensing
Camera (FSC).
¾The Forward Sensing Camera (FSC)
is installed to the windscreen.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) for windscreen repair
and replacement.
¾When cleaning the windscreen, do
not allow glass cleaners or similar
cleaning fluids to get on the
Forward Sensing Camera (FSC)
lens. In addition, do not touch the
Forward Sensing Camera (FSC)
lens.
¾When performing repairs around
the rearview mirror, consult an
expert repairer (we recommend an
Authorised Mazda Repairer).
¾Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) regarding cleaning of the
camera lens.¾Do not hit or apply strong force to
the Forward Sensing Camera (FSC)
or the area around it. If the
Forward Sensing Camera (FSC) is
severely hit or if there are cracks or
damage caused by flying gravel or
debris in the area around it, stop
using the following systems and
consult an expert repairer (we
recommend an Authorised Mazda
Repairer).
¾High Beam Control System
(HBC)
¾Adaptive LED Headlights (ALH)
¾Lane Departure Warning System
(LDWS)
¾Traffic Sign Recognition System
(TSR)
¾Distance & Speed Alert (DSA)
¾Driver Attention Alert (DAA)
¾Mazda Radar Cruise Control
(MRCC)
¾Mazda Radar Cruise Control
with Stop & Go function (MRCC
with Stop & Go function)
¾Lane-keep Assist System (LAS)
¾Cruising & Traffic Support (CTS)
¾Smart Brake Support (SBS)
¾The direction in which the Forward
Sensing Camera (FSC) is pointed
has been finely adjusted. Do not
change the installation position of
the Forward Sensing Camera (FSC)
or remove it. Otherwise, it could
result in damage or malfunction.
¾Always use tyres for all wheels that
are of the specified size, and the
same manufacturer, brand, and tread
pattern. In addition, do not use tyres
with significantly different wear
patterns on the same vehicle as the
system may not operate normally.
When Driving
i-ACTIVSENSE
4-217

xNarrow lane roads due to road
construction or lane closures.
xThe vehicle ahead enters the radar
sensor's blind spot.
xThe vehicle ahead is running
abnormally due to accident or
vehicle damage.
xRoads with repeated up and down
slopes
xDriving on poor roads or unpaved
roads.
xThe distance between your vehicle
and the vehicle ahead is extremely
short.
xA vehicle suddenly comes close,
such as by cutting into your lane.
xTo prevent incorrect operation of the
system, use tyres of the same
specified size, manufacturer, brand,
and tread pattern on all four wheels.
In addition, do not use tyres with
significantly different wear patterns
or tyre pressures on the same vehicle
(Including the temporary spare tyre).
xIf the battery power is weak, the
system may not operate correctly.
xWhen driving on roads with little
traffic and few vehicles ahead or
obstructions for the front radar
sensor to detect, “Safety and Driver
Support Systems Temporarily
Disabled. Front Radar Obscured.
Drive Safely” may be temporarily
displayed, however, this does not
indicate a problem.
xThe radar sensors are regulated by
the relevant radio wave laws of the
country in which the vehicle is
driven. If the vehicle is driven
abroad, authorization from the
country in which the vehicle is driven
may be required.
Front Side Radar Sensor*
▼Front Side Radar Sensor
Your vehicle is equipped with front
side radar sensor. The following
systems also use the front side radar
sensor.
xFront Cross Traffic Alert (FCTA)
The front side radar sensor function by
detecting the radio waves reflected off
a vehicle approaching from the front or
an obstruction sent from the radar
sensor.
1. Front side radar sensor

The front side radar sensors are
installed inside the front bumper, one
on each side.
Always keep the surface of the front
bumper near the front side radar
sensors clean so that they operate
normally. Also, do not apply items such
as stickers.
Refer to Exterior Care on page 6-54.
CAUTION
If the front bumper receives a severe
impact, the system may no longer
operate normally. Stop the system
immediately and have the vehicle
inspected at an expert repairer (we
recommend an Authorised Mazda
Repairer).
When Driving
i-ACTIVSENSE
4-222*Some models.

Front Camera/Side
Cameras/Rear Camera
*
▼Front Camera/Side Cameras/Rear
Camera
Your vehicle is equipped with a front
camera, side cameras, and a rear
camera. The 360°View Monitor uses
each camera.
Refer to 360°View Monitor on page
4-185.
The front camera, side cameras, and
rear camera shoot images of the area
surrounding the vehicle.
Each camera is installed to the
following positions.
1. Side cameras
2. Front camera
3. Rear camera
Driver Monitoring
Camera
*
▼Driver Monitoring Camera
The driver monitoring camera detects
changes in the driver's facial features
and estimates the amount of
accumulated fatigue and sleepiness of
the driver.
1. Driver monitoring camera
NOTE
xDriver Monitoring (DM) and the
earlier collision warning may not
operate normally under the following
conditions.
xThe driver monitoring camera is
covered with something.
xYou are driving the vehicle while
leaning on the steering wheel.
xYou are wearing glasses or
sunglasses.
xA cap or hat you are wearing
partially blocks the driver
monitoring camera's view of your
eyes, you have long bangs partially
covering your eyes, or a part of
your face is invisible due to a face
mask.
xThe lighting conditions change
significantly (such as backlight,
light from the side, or direct light
from the setting sun, and the
headlights of on-coming vehicles).
When Driving
i-ACTIVSENSE
4-226*Some models.

Tyre Pressure Monitoring
System (TPMS)
*
▼Tyre Pressure Monitoring System
(TPMS)
The TPMS monitors the air pressure of
each tyre and if it decreases below the
specified value, the system
notifies the
driver by turning on the TPMS warning
light in the instrument cluster and
indicating a message on the
multi-information display.
For the TPMS, the air pressure data
sent from the tyre pressure sensors
installed on each wheel via radio signal
is received by the receiver unit in the
vehicle to monitor the tyre pressures.
1. Tyre pressure sensors

In addition, the current tyre pressures
can be checked using the centre
display.
Refer to the Vehicle Status Monitor
section in the Mazda Connect
Owner's Manual.
NOTE
xWhen the ambient temperature is
low, the tyre temperatures also
decrease. If the tyre temperatures
decrease, the air pressure in the tyres
will also decrease which could turn
on the TPMS warning light.
xBefore driving, visually inspect the
tyres for abnormalities. Additionally,
inspect the tyre pressures monthly. A
digital type air pressure gauge is
recommended for inspecting the tyre
pressures.
The TPMS is not a substitute for your
own periodic inspection of the tyres.
Always inspect the tyres yourself
periodically.
CAUTION
¾Each tyre, including the spare (if
provided), should be checked
monthly when cold and inflated to
the inflation pressure recommended
by the vehicle manufacturer on the
vehicle placard or tyre
inflation
pressure label. (If your vehicle has
tyres of a different size than the size
indicated on the vehicle placard or
tyre inflation pressure label, you
should determine the proper tyre
inflation pressure for those tyres.)
As an added safety feature, your
vehicle has been equipped with a
tyre pressure monitoring system
(TPMS) that illuminates a low tyre
pressure telltale when one or more
of your tyres is
significantly
under-inflated. Accordingly, when
the low tyre pressure telltale
illuminates, you should stop and
check your tyres as soon as possible,
and inflate them to the proper
pressure. Driving on a significantly
under-inflated tyre causes the tyre to
overheat and can lead to tyre failure.
Under-inflation also reduces fuel
efficiency and tyre tread life, and may
affect the vehicle's handling and
stopping ability.
When Driving
Tyre Pressure Monitoring System (TPMS)
4-232*Some models.

Please note that the TPMS is not a
substitute for proper tyre
maintenance, and it is the driver's
responsibility to maintain correct tyre
pressure, even if under-inflation has
not reached the level to trigger
illumination of the TPMS low tyre
pressure telltale.
Your vehicle has also been equipped
with a TPMS malfunction indicator to
indicate when the system is not
operating properly.
The TPMS malfunction indicator is
combined with the low tyre pressure
telltale. When the system detects a
malfunction, the telltale will flash for
approximately one minute and then
remain continuously illuminated.
This sequence will continue upon
subsequent vehicle start-ups as long
as the malfunction exists. When the
malfunction indicator is illuminated,
the system may not be able to detect
or signal low tyre pressure as
intended. TPMS malfunctions may
occur for a variety of reasons,
including the installation of
replacement or alternate tyres or
wheels on the vehicle that prevent
the TPMS from functioning properly.
Always check the TPMS malfunction
telltale after replacing one or more
tyres or wheels on your vehicle to
ensure that the replacement or
alternate tyres and wheels allow the
TPMS to continue to function
properly.
¾To avoid false readings, the system
samples for a little while before
indicating a problem. As a result it
will not instantaneously register a
rapid tyre deflation or blow out.▼If there is a problem with the Tyre
Pressure Monitoring System
(TPMS)
If the TPMS warning light flashes, there
may be a problem with the system.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) to have the system inspected.
Refer to Tyre Pressure Monitoring
System (TPMS) Warning Indication/
Warning Light (Flashing) on page
7-57.
In the following cases, the system
cannot recognise the tyre pressures
correctly and the TPMS warning light
may flash.
xThere is equipment or a device
nearby emitting radio signals the
same as a tyre pressure sensor.
xA metallic object such as a
non-genuine electronic device is
installed near the centre of the
instrument panel (obstructs the radio
signals from the tyre pressure sensors
to the receiver).
xA device such as one of the following
is used in the cabin.
xElectronic devices such as a
computer.
xConverter devices such as a
DC-AC converter.
xThere is a large accumulation of
snow or ice around the vehicle tyres.
xThe battery in a tyre pressure sensor
is dead.
xA wheel not equipped with a tyre
pressure sensor is used.
xTyres employing steel in the sidewall
of the tyre are installed.
xTyre chains are used.
▼When a tyre pressure decreases
If the TPMS warning light turns on, a
tyre pressure may be low. Inspect the
When Driving
Tyre Pressure Monitoring System (TPMS)
4-233

tyre pressures and adjust them to the
correct inflation pressure.
Refer to Tyre Pressure Monitoring
System (TPMS) Warning Indication/
Warning Light (Turns on) on page
7-60.
▼Tyres and Wheels
CAUTION
When inspecting/adjusting the tyre
pressures, do not apply excessive force
to the air valve of the tyre pressure
sensor. Otherwise, the tyre pressure
sensor could be damaged.
When changing tyres and wheels
When changing the tyres or wheels
(such as installing winter tyres), it will
be necessary to register the ID signal
code of the tyre pressure sensor to the
TPMS.
Have an expert repairer (we
recommend an Authorised Mazda
Repairer) do the registration or register
the ID signal codes of the tyre pressure
sensors using the following procedure.
NOTE
The tyre pressure sensors on each
wheel have a unique ID signal code.
For the TPMS to operate correctly, the
ID signal codes of the tyre pressure
sensors need to be registered to the
system.
1. Wait more than 19 minutes after
changing a tyre or wheel.
2. After more than 19 minutes have
passed, drive the vehicle at a speed
of about 25 km/h (16 mph) or
faster for 3 minutes or longer. While
driving, the ID signal codes of the
tyre pressure sensors are
automatically registered.
NOTE
If you drive the vehicle within 19
minutes of changing a tyre or wheel,
the TPMS warning light will flash
because the ID signal codes for the
tyre pressure sensors were not
registered. In this case, stop the vehicle
and register the ID signal codes of the
tyre pressure sensors following the
procedure.
When replacing tyres and wheels
CAUTION
¾When replacing the tyres and
wheels, consult an expert repairer
(we recommend an Authorised
Mazda Repairer) Otherwise, the tyre
pressure sensors could be damaged
when replacing them.
¾Do not install non-genuine wheels. If
wheels other than genuine ones are
installed, it may not be possible to
install the tyre pressure sensors.
When replacing a tyre or wheel, always
install the tyre pressure sensor. The
following combinations of tyres,
wheels, or tyres and wheels are
possible.
xThe tyre pressure sensor from the old
wheel is removed and it is installed
to the new wheel.
xOnly a tyre is replaced without
replacing the tyre pressure sensor
and wheel.
xA new tyre pressure sensor is
installed to a new wheel.
When Driving
Tyre Pressure Monitoring System (TPMS)
4-234