2019 MAZDA MODEL CX-30 open bonnet

Theft-Deterrent System*
▼Theft-Deterrent System
If the theft-deterrent system detects an
inappropriate entry into the vehicle or
the intrusion sensor detects movement
in the vehicle which could result in the
vehicle (with the intrusion sensor) or
its contents being stolen, the alarm
alerts the surrounding area of an
abnormality by sounding the siren/
horn and flashing the hazard warning
lights.

The system will not function unless it's
properly armed. So when you leave the
vehicle, follow the arming procedure
correctly.
Intrusion sensor
*
The intrusion sensor uses ultrasonic
waves to detect movement inside the
vehicle and to raise an alert of an
intrusion into the vehicle.

The intrusion sensor detects certain
kinds of movement inside the vehicle,
however, it may also respond to
phenomenon outside the vehicle such
as vibrations, loud noise, wind, and air
currents.
CAUTION
In order for the intrusion sensor to
operate appropriately, be aware of the
following:
¾Do not hang clothing or objects from
a head restraint or a coat hook.
¾Return the extension sunvisors to
their original positions.
¾Do not blind the intrusion sensor by
covering it or placing objects over it.
¾Do not allow the intrusion sensor to
get soiled or wipe it with a liquid.
¾Do not shock or cause an impact to
the intrusion sensor or the intrusion
sensor bezel.
¾Do not install seats that are not
Mazda genuine products.
¾To prevent obstruction of intrusion
sensor, do not place objects or cargo
near the intrusion sensor that are
higher than the head restraints.

1. Intrusion sensor and intrusion
sensor bezel
▼Operation
Siren/Horn triggering conditions
The siren/horn sounds intermittently
and the hazard warning lights flash for
about 30 seconds when the system is
triggered by any one of the following:
With the intrusion sensor
xUnlocking a door with the auxiliary
key, door lock switch, or an inside
door-lock knob.
xForcing open a door, the bonnet or
the liftgate.
xOpening the bonnet by operating
the bonnet release handle.
xSwitching the ignition ON without
using the push button start.
xThe intrusion sensor detects a
movement in the vehicle.
Before Driving
Security System
*Some models.3-49

The system will be triggered again (up
to 10 times) if one of the above
conditions remains.

xDisconnecting the battery terminal
(the hazard warning lights do not
flash).
The system will be triggered about 10
times.
Without the intrusion sensor
xUnlocking a door with the auxiliary
key, door lock switch, or an inside
door-lock knob.
xForcing open a door, the bonnet or
the liftgate.
xOpening the bonnet by operating
the bonnet release handle.
xSwitching the ignition ON without
using the push button start.
If the system is triggered again, the
lights and horn will activate until the
driver's door or the liftgate is unlocked
with the transmitter.
NOTE
xThe liftgate does not open while the
theft-deterrent system is operating.
xIf the battery goes dead while the
theft-deterrent system is armed, the
siren/horn will activate and the
hazard warning lights will flash when
the battery is charged or replaced.
▼How to Arm the System
1. Close the windows and the
sunroof* securely.
NOTE
(With the intrusion sensor)
Even with a window or the sunroof*
open, the system can be armed,
however, leaving the windows or
the sunroof
* even partially open can
invite theft, and wind blowing into
the vehicle could trigger the alarm.
The intrusion sensor function can
also be cancelled.
Refer to Cancelling the Intrusion
Sensor (With Intrusion Sensor) on
page 3-51.
2. Switch the ignition OFF.
3. Make sure the bonnet, the doors,
and the liftgate are closed.
4. Press the lock button on the
transmitter.
The hazard warning lights will flash
once.
The following method will also arm
the theft-deterrent system:
Press the door-lock switch “
”
while any door is open and then
close all of the doors.
(With the advanced keyless
function)
Touch the sensing area of the door
lock touch sensor.

The security indicator light in the
instrument cluster flashes twice per
second for 20 seconds.

5. After 20 seconds, the system is fully
armed.
Before Driving
Security System
3-50*Some models.

NOTE
xThe theft-deterrent system can
also be armed by activating the
auto relock function with all the
doors, the liftgate and the bonnet
closed.
Refer to Transmitter on page 3-5.
xThe system will disarm if one of
the following operations takes
place within 20 seconds after
pressing the lock button:
xUnlocking any door.xOpening any door.xOpening the bonnet.xSwitching the ignition ON.
To rearm the system, do the
arming procedure again.
xWhen the doors are locked by
pressing the lock button on the
transmitter while the
theft-deterrent system is armed,
the hazard warning lights will
flash once to indicate that the
system is armed.
▼Cancelling the Intrusion Sensor
(With the Intrusion Sensor)
If the theft deterrent system has been
armed while any of the following
conditions are present, cancel the
intrusion sensor to prevent the alarm
from triggering unnecessarily.
xLeaving the vehicle with a movable
object, passengers or pets remaining
inside.
xLeaving an object inside the vehicle
that can roll around, such as when
the vehicle is placed on a tilting,
unstable surface when being
shipped.
xHanging small objects/accessories in
the vehicle, hanging clothing on a
coat hook, or placing other items
which can move easily inside the
vehicle.
xParking in an area where there is
strong vibration or loud noise.
xWhen using a high pressure or
automatic car wash.
xContinuous shock and vibration from
hail or thunder and lightning is
transmitted to the vehicle.
xDoors are locked with a window or
the sunroof* left open.xAn accessory heater or device that
produces moving air and vibration
operates while the theft deterrent
system is armed.
NOTE
If any door or the liftgate remains
closed for 30 seconds, all the doors
and the liftgate automatically re-lock
and the theft deterrent system arms
even if a window and the sunroof
* is
left open.

To cancel the intrusion sensor, press
the intrusion sensor cancel button on
the transmitter within 20 seconds after
pressing the lock button.
The hazard warning lights will flash 3
times.
NOTE
xTo reactivate the intrusion sensor,
turn off the armed theft-deterrent
system and then rearm it.
xThe intrusion sensor is operational
when the theft-deterrent system is
armed. To cancel the intrusion
sensor, press the intrusion sensor
cancel button each time the
theft-deterrent system is armed.
▼To Turn Off an Armed System
An armed system can be turned off
using any one of the following
methods:
Before Driving
Security System
*Some models.3-51

position if force is applied to the
steering wheel. Release the force
applied to the steering wheel to
stop engine idling).
xThe vehicle is stopped by
depressing the brake pedal.
xThe vehicle is not driven on a
slope.
xThe vehicle is not stopped
suddenly.
NOTE
Under the following conditions, a
period of time is required to stop
engine idling
xThe battery power is depleted for
some reasons such as the vehicle has
not been driven for a long period.
xThe ambient temperature is high or
low.
xAfter the battery terminals are
disconnected for some reasons such
as for battery replacement.
x(SKYACTIV-D 1.8)
After PM removal is performed by
the diesel particulate filter.
Engine does not restart
If the following operations are
performed while the idling is stopped,
the engine will not restart for safety
reasons. In such cases, start the engine
using the normal method.
x(European model)
xThe bonnet is opened.xThe driver's seat belt is unfastened
and the driver's door is opened.
x(With M Hybrid)
xAutomatic transmission
The driver's seat belt is unfastened
and the driver's door is opened.
xManual transmission
The driver's door is opened.
Engine-stop period is short or time
until next engine idle stop is long
xThe ambient temperature is high or
low.
xThe battery power is depleted.xPower consumption by the vehicle's
electrical parts is high.
Engine restarts automatically while
engine idling is stopped
Under the following conditions, the
engine restarts automatically.
xThe i-stop OFF switch is pressed until
the beep sounds.
xThe air conditioner is operated with
the airflow mode in the
position.xThe temperature setting dial of the
air conditioner is in the maximum
heating or maximum cooling (A/C
ON) position.
x(Automatic air-conditioning)
The cabin temperature is largely
different from the set temperature of
the air conditioner.
xThe brakes are released slightly on a
slope and the vehicle begins to
move.
xTwo minutes have elapsed since the
idling was stopped.
xThe battery power is depleted.x(Automatic transmission)
Engine idling is stopped while the
vehicle is stopped
xThe accelerator pedal is depressed
with the selector lever in the D or
M (not in second gear fixed mode)
position.
xThe selector lever is shifted to the R
position.
xThe selector lever is shifted from N
or P position to D or M (not in
second gear fixed mode) position.
When Driving
Start/Stop Engine
4-15

xThe steering wheel is operated
with the selector lever in the D or
M (not in second gear fixed mode)
position.
xThe selector lever is in the M
position and the second gear fixed
mode is selected.
xThe steering wheel is operated.
Engine idling is stopped while
driving
xThe selector lever is in a position
other than the D position.
xThe accelerator pedal is depressed.xSport mode is selected.xThe steering wheel is operated.x(Manual transmission (With M
Hybrid))
xThe shift lever is shifted to the R
position.
xThe brake pedal is depressed with
the shift lever in the neutral
position.
xThe accelerator pedal is depressed.xThe shift lever is shifted to a
position other than neutral with
the brake pedal released and the
clutch pedal depressed.
xThe driver's seat belt is unfastened.
x(Except European model)
x(Manual transmission)
With the shift lever in the neutral
position, the driver's seat belt is
unfastened, the driver's door is
opened, or the bonnet is opened.
x(Automatic transmission)
With the selector lever in the P or
N position, or the D/M range, the
driver's seat belt is unfastened, the
driver's door is opened, or the
bonnet is opened.
Selector lever is operated while
engine idling is stopped and the
vehicle is stopped (automatic
transmission)
If the selector lever is shifted from D or
M (not in second gear fixed mode)
position to N or P position while
engine idling is stopped, the engine
does not restart even when the brake
pedal is released. The engine will
restart if the brake pedal is depressed
again or the selector lever is shifted to
the D, M (not in second gear fixed
mode), or R position. (For the
purposes of safety, always keep the
brake pedal depressed when shifting
the selector lever.)
If the selector lever is shifted from the
D or M (not in second gear fixed
mode) to the N or P position, and the
driver's seat belt is unfastened or the
driver's door is opened, the engine
restarts.
Battery terminals are disconnected
Engine idling may not stop right after
the battery terminals are disconnected.
In addition, if the battery is replaced,
the i-stop functions must be verified.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer).
▼i-stop OFF Switch
When pressing the switch, the i-stop
function stops and the i-stop OFF
switch indicator light turns on. If the
switch is pressed again, the i-stop
function becomes operational and the
When Driving
Start/Stop Engine
4-16

automatically to ensure safety. Start
the engine using the normal method.
xThe bonnet is opened.xThe driver's seat belt is unfastened
and the driver's door is opened.
x(Except European model)
x(Manual transmission)
A sound is activated when the
door is opened while the engine
idling is stopped with the shift
lever in a position other than
neutral. In this case, the engine
does not restart automatically to
ensure safety. Shift the shift lever to
neutral and start the engine.
xIf the i-stop warning light (amber)
remains on while the engine is
running, the battery performance
may have decreased. Have your
vehicle inspected by an expert
repairer (we recommend an
Authorised Mazda Repairer).
NOTE
A problem in the system may be
indicated under the following
conditions. Have your vehicle
inspected by an expert repairer (we
recommend an Authorised Mazda
Repairer).
xThe light does not turn on when the
ignition is switched ON.
xThe light continues to remain on
while the engine is running.
When the light is flashing
The light continues to flash if the
system has a malfunction. Have your
vehicle inspected by an expert repairer
(we recommend an Authorised Mazda
Repairer).
i-stop indicator light (green)
When the light is turned on
xThe light turns on while engine idling
is stopped and turns off when the
engine is restarted.
When the light is flashing
x(Manual transmission)
xThe light flashes when the shift
lever is shifted to a position other
than the neutral while engine
idling is stopped to notify the
driver that engine idling is stopped.
xBy depressing the clutch pedal, the
engine restarts automatically and
the light turns off.
x(European model)
The light flashes when the driver's
door is opened while engine idling is
stopped to notify the driver that
engine idling is stopped. It turns off
when the driver's door is closed.
When Driving
Start/Stop Engine
4-19

Operating Tips
▼Operating Tips
xOperate the air-conditioning system
with the engine running.
xTo prevent the battery from being
discharged, do not leave the fan
control dial/switch on for a long
period of time with the ignition
switched ON when the engine is not
running.
x(With i-stop)
The
airflow amount may decrease
slightly while the i-stop function is
operating.
xClear all obstructions such as leaves,
snow and ice from the bonnet and
the air inlet in the cowl grille to
improve the system efficiency.
xUse the air-conditioning system to
defog the windows and dehumidify
the air.
xThe recirculate mode should be used
when driving through tunnels or
while in a
traffic jam, or when you
would like to shut off outside air for
quick cooling of the interior.
xUse the outside air position for
ventilation or windscreen defrosting.
xIf the vehicle has been parked in
direct sunlight during hot weather,
open the windows to let warm air
escape, then run the air-conditioning
system.
xRun the air conditioner about 10
minutes at least once a month to
keep internal parts lubricated.
xHave the air conditioner checked
before the weather gets hot. Lack of
refrigerant may make the air
conditioner less efficient.
The refrigerant specifications are
indicated on a label attached to the
inside of the engine compartment. If
the wrong type of refrigerant is used,
it could result in a serious
malfunction of the air conditioner.
Consult a professional, government
certified repairer for the inspection
or repair because a special device is
required for the air conditioner
maintenance.
For details, consult an expert repairer
(we recommend an Authorised
Mazda Repairer).
1. Label
Interior Features
Air-Conditioning System
5-2

Pull over to a safe location, then
switch the ignition off and make sure
the fan is not running before
attempting to work near the cooling
fan:
Working near the cooling fan when it is
running is dangerous. The fan could
continue running indefinitely even if
the engine has stopped and the engine
compartment temperature is high. You
could be hit by the fan and seriously
injured.
Do not leave items in the engine
compartment:
After you have finished checking or
doing servicing in the engine
compartment, do not forget and leave
items such as tools or rags in the
engine compartment.
Tools or other items left in the engine
compartment could cause engine
damage or a fire leading to an
unexpected accident.
Bonnet
▼Bonnet
WARNING
Always check that the bonnet is
closed and securely locked:
A bonnet that is not closed and
securely locked is dangerous as it could
fly open while the vehicle is moving
and block the driver's vision which
could result in a serious accident.
▼Opening the Bonnet
1. With the vehicle parked, pull the
release handle to unlock the
bonnet.

2. Insert your hand into the bonnet
opening , slide the latch lever to the
left, and lift up the bonnet.


3. Grasp the support rod in the
padded area and secure it in the
Maintenance and Care
Owner Maintenance
6-17