2019 Hyundai Tucson lock

Maintenance
7-64
Engine compartment main fuse panel (PCB Block)
Fuse Name SymbolFuse ratingCircuit Protected
FUSE
DCU 3DCU315A Dosing Control Unit
DCU2/
E-CVVT220A DCU2 : Dosing Control Unit
E-CVVT2 : PCM
DCU1/
E-CVVT120A DCU1 : Dosing Control Unit
E-CVVT1 : PCM
WIPER FRT125A Front Wiper Motor
TCU 115A G4NA : PCM
G4FJ/D4HA : TCM
A/C COMP10AE/R Junction Block (RLY. 3)
ECU 320A G4NA/G4FD : PCM/ECM, G4FJ: ECM/TCM, G4KJ : PCM
HORN15A Horn Relay
BATTERY
MANAGEMENT10A Battery Sensor
SENSOR 210A
G4NA : Oil Control Valve #1/#2, Camshaft Position Sensor #1/#2, Purge Control Solenoid Valve, E/R Junction Block (RLY.3), Variable Intake Solenoid Valve
G4FD/G4FJ : Oil Control Valve #1/#2, Oil Level Sensor (G4FD), Purge Control Solenoid Valve, E/R Junction Block (RLY.3)
D4HA/D4FE : Crankshaft Position Sensor (D4HA), EGR Cooling Bypass Solenoid Valve (D4HA), Stop Lamp Switch, E/R Junction Block (RLY. 3/6/14)
G4KJ : Oil Control Valve, Purge Control Solenoid Valve, Variable Intake Solenoid Valve, E/R Junction Block (RLY.3)
TLe UK 7.qxp 5/10/2018 1:38 PM Page 64

7-65
7
Maintenance
Fuse Name SymbolFuse ratingCircuit Protected
FUSE
SENSOR 115A
G4NA/G4KJ : Oxygen Sensor (Up/Down)
G4FD : PCM/ECM, Oxygen Sensor (Up/Down)
G4FJ : ECM, Oxygen Sensor (Up/Down)
D4HA/D4FE : Electronic VGT Actuator (D4HA), Lambda Sensor #1/#2, PM Sensor,Mass Air Flow Sensor (D4FE), Fuel Pressure Regulating Valve
(D4HA), Oil Pump Solenoid Valve (D4FE), Stop Lamp Switch (D4FE)
ECU 220A G4NA/G4FD : Ignition Coil #1/#2/#3/#4, Condenser, G4FJ : Ignition Coil #1/#2/#3/#4, D4HA/D4FE : ECM
ECU 515A G4FD : PCM/ECM, G4FJ : ECM
ECU 415A G4NA/G4FD : PCM/ECM, G4FJ/D4HA/D4FE : ECM, G4KJ : PCM
SENSOR 310A
G4NA/G4FD/G4KJ : Injector #1/#2/#3/#4 (G4NA), E/R Junction Block (RLY. 1, RLY.9)
G4FJ : RCV Control Solenoid Valve, Brake Booster Vacuum Pressure Switch, E/R Junction Block (RLY. 1, RLY.9)
D4HA/D4FE : Mass Air Flow Sensor (D4HA), Oil Pump Solenoid Valve (D4HA), E/R Junction Block (RLY. 1, RLY.9), Electronic VGT Actuator (D4FE)
H/LP
WASHER20AE/R Junction Block (RLY. 12)
DEICER15A E/R Junction Block (RLY. 8)
Engine compartment main fuse panel (PCB Block)
TLe UK 7.qxp 5/10/2018 1:38 PM Page 65

Maintenance
7-66
Fuse Name SymbolFuse ratingCircuit Protected
FUSE
FUEL
PUMPFUEL
PUMP20A E/R Junction Block (RLY.14)
MODULE 17.5A D4HA/D4FE : Glow Relay Unit, Fuel Filter Warning Sensor,
E/R Junction Block (RLY. 10)
B/ALARM HORN10A E/R Junction Block (RLY. 7)
ACTIVE
BONNET10AG4FD/G4FJ/D4HA/D4FE : Active Bonnet Lift Control Module
ABS 310A ABS Control Module, ESP Control Module
MODULE 215A G4FJ : Vacuum Pump
POWER
OUTLET FRTPOWER
OUTLET FRT20AFront Power Outlet & Cigarette Light
ECU 610A
G4NA/G4FD : ECM/PCM
G4FJ : ECM
D4HA/D4FE : ECM, Oil Level Sensor
G4KJ : PCM
Engine compartment main fuse panel (PCB Block)
TLe UK 7.qxp 5/10/2018 1:38 PM Page 66

7-67
7
Maintenance
Fuse Name SymbolFuse ratingCircuit Protected
FUSE
TCU 215A [A/T] Transaxle Range Switch,TCM, ATM Shift Lever
[M/T] Back-Up Lamp Switch
B/UP LAMP10A Transaxle Range Switch, Electro Chromic Mirror,
Rear Combination Lamp (IN) LH/RH, TCM, Back-Up Lamp Switch,
MTS E-Call Module, Smart Junction Block (IPS Control Module)
POWER
OUTLET REARPOWER
OUTLET REAR20ARear Power Outlet
WIPER FRT210A BCM, G4NA/G4KJ : PCM/ECM
MODULE 3MODULE310A E/R Junction Block (RLY. 14)
ECU 1E130AEngine Control Relay
Engine compartment main fuse panel (PCB Block)
TLe UK 7.qxp 5/10/2018 1:38 PM Page 67

7-68
Maintenance
LIGHT BULBS
Prior to working on the light,
firmly apply the parking brake,
ensure that the ignition switch is
in the LOCK/OFF position and
turn off the lights to avoid sud-
den movement of the vehicle and
burning your fingers or receiving
an electric shock.
WARNING
Consult a HYUNDAI authorised
repairer to replace most vehicle light
bulbs. It is difficult to replace vehicle
light bulbs because other parts of the
vehicle must be removed before you
can get to the bulb. This is especially
true for removing the headlamp
assembly to get to the bulb(s).
Removing/installing the headlamp
assembly can result in damage to
the vehicle.Be sure to replace the burned-out
bulb with one of the same wattage
rating. Otherwise, it may cause
damage to the fuse or electric
wiring system.
Information
After heavy driving, rain or washing,
headlamp and tail lamp lenses could
appear frosty. This condition is caused
by the temperature difference between
the lamp inside and outside. This is
similar to the condensation on your
windows inside your vehicle during the
rain and doesn’t indicate a problem
with your vehicle. If the water leaks
into the lamp bulb circuitry, we rec-
ommend that the system be checked
by a HYUNDAI authorised repairer.
Information - Desiccant
(if equipped)
This vehicle is equipped with desic-
cant to reduce fogging inside the head-
lamp due to moisture.
The desiccant is consumable and its
performance may change based on the
used period or environment.
If fogging inside the headlamp due to
moisture continues for a long time, we
recommend that you consult a
HYUNDAI authorised repairer.
Information - Traffic Change
The low beam light distribution is
asymmetric. If you go abroad to a
country with opposite traffic direc-
tion, this asymmetric part will dazzle
oncoming car driver. To prevent daz-
zle, ECE regulation demand several
technical solutions (ex. automatic
change system, adhesive sheet, down
aiming). These headlamps are
designed not to dazzle opposite driv-
ers. So, you need not change your
headlamps in a country with opposite
traffic direction.i
i
i
NOTICE
TLe UK 7.qxp 5/10/2018 1:38 PM Page 68

7-70
Maintenance
1. Open the bonnet.
2. Disconnect the negative battery cable.
3. Remove the bulb cover by turning it counterclockwise.
4. Disconnect the bulb socket-con- nector. 5. Unsnap the bulb retaining wire by
pressing the end and pushing it
upward.
6. Remove the bulb from the head- lamp assembly.
7. Install a new bulb and snap the bulb retaining wire into position by
aligning the wire with the groove
on the bulb.
8. Connect the bulb socket-connec- tor.
9. Install the bulb cover by turning it clockwise.
Information
The headlamp aiming should be adjust-
ed after an accident or after the head-
lamp assembly is reinstalled at a
HYUNDAI authorised repairer.
Turn signal lamp
1. Open the bonnet.
2. Disconnect the negative batterycable.
3. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
4. Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
i
OTLE078013
OTLE078015
■Low Beam Assist – Static
■High/Low beam
Low
High
OTLE078019
TLe UK 7.qxp 5/10/2018 1:38 PM Page 70

7-71
7
Maintenance
5. Insert a new bulb by inserting itinto the socket and rotating it until
it locks into place.
6. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
7. Push the socket into the assembly and turn the socket clockwise.
Position lamp/Daytime running lamp
If the LED lamp does not operate, we
recommend you to have the vehicle
checked by a HYUNDAI authorised
repairer.
Type B
(1) Headlamp (Low)
(2) Headlamp (High)
(3) Turn signal lamp
(4) Position lamp
(5) Fog lamp
(6) Daytime running lamp
(7) Low Beam Assist – Static
Lamps
If the LED lamp does not operate, we
recommend that you have the vehi-
cle checked by a HYUNDAI autho-
rised repairer.
Front fog lamp (if equipped)
1. Loosen the pin-type retainers ofthe under cover and then remove
the undercover.
2. Reach your hand into the back of the front bumper.
3. Disconnect the power connector from the socket.
OTLE078107
OTLE078032
OTLE078106
TLe UK 7.qxp 5/10/2018 1:38 PM Page 71

7-72
Maintenance
4. Remove the bulb-socket from the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots of
the housing.
5. Install a new bulb-socket into the housing by aligning the tabs on the
socket with the slots in the housing.
Push the socket into the housing
and turn the socket clockwise.
Side repeater lamp replacement
Type A
If the light bulb does not operate, we
recommend you to have the vehicle
checked by a HYUNDAI authorised
repairer.
Type B
1. Remove the lamp assembly from the vehicle by prying the lens and
pulling the assembly out.
2. Disconnect the bulb electrical con- nector.
3. Separate the socket and the lens parts by turning the socket coun-
terclockwise until the tabs on the
socket align with the slots on the
lens part. 4. Remove the bulb by pulling it
straight out.
5. Insert a new bulb in the socket.
6. Reassemble the socket and the lens part.
7. Connect the bulb electrical con- nector.
8. Reinstall the lamp assembly to the body of the vehicle.
OTL075065
OTL075066
TLe UK 7.qxp 5/10/2018 1:39 PM Page 72