2019 HYUNDAI I10 Owners Manual

7-17
07
You may not be able to identify a tyre
with low pressure by simply looking at
it. Always use a good quality tyre
pressure gauge to measure. Please
note that a tyre that is hot (from being
driven) will have a higher pressure
measurement than a tyre that is cold.
A cold tyre means the vehicle has
been sitting for 3 hours and driven for
less than 1 mile (1.6 km) in that 3
hour period.
Allow the tyre to cool before measur-
ing the inflation pressure. Always be
sure the tyre is cold before inflating to
the recommended pressure.
WARNING

7-18
Emergency situations
WARNING
&KDQJLQJDW\UHFDQEHGDQJHURXV
)ROORZWKHLQVWUXFWLRQVLQWKLVVHF-
WLRQ ZKHQ FKDQJLQJ D W\UH WR
UHGXFHWKHULVNRIVHULRXVLQMXU\RU
GHDWK
CAUTION
%HFDUHIXODV\RXXVHWKHMDFNKDQ-
GOHWRVWD\FOHDURIWKHIODWHQG7KH
IODWHQGKDVVKDUSHGJHVWKDWFRXOG
FDXVHFXWV
-DFNDQGWRROV
OAC3079028TU
(1) Jack handle
(2) Jack
(3) Wheel lug nut wrench
(4) Towing hook
The jack, jack handle, wheel lug nut
wrench, and towing hook are stored
in the luggage compartment under
the luggage box cover.
OAC3079004TU
The jack is provided for emergency
tyre changing only.
Turn the winged hold down bolt coun-
terclockwise to remove the spare
tyre.
Store the spare tyre in the same com-
partment by turning the winged hold
down bolt clockwise.
To prevent the spare tyre and tools
from “rattling”, store them in their
proper location.
OAC3079005TU
If it is hard to loosen the tyre hold-
down wing bolt by hand, you can
loosen it easily using the jack handle.
1. Put the jack handle (1) inside of the
tyre hold-down wing bolt.
2. Turn the tyre hold-down wing bolt
counterclockwise with the jack
handle.
IF YOU HAVE A FLAT TYRE
ãWITH SPARE TYRE IF EQUIPPED
ä

7-19
07
&KDQJLQJW\UHV
WARNING
$ YHKLFOH FDQ VOLS RU UROO RII RI D
MDFN FDXVLQJ VHULRXV LQMXU\ RU
GHDWKWR\RXRUWKRVHQHDUE\7DNH
WKHIROORZLQJVDIHW\SUHFDXWLRQV

7-20
Emergency situations
OAC3079008TU
7. Place the jack at the designated
jacking position under the frame
closest to the tyre you are chang-
ing. The jacking positions are
plates welded to the frame with two
notches. Never jack any other
position or part of the vehicle.
Doing so may damage the side
seal molding or other parts of the
vehicle.
OAC3079009TU
8. Insert the jack handle into the jack
and turn it clockwise, raising the
vehicle until the tyre clears the
ground. Make sure the vehicle is
stable on the jack.9. Loosen the lug nuts with the wheel
lug nut wrench and remove them
with your fingers. Remove the
wheel from the studs and lay it flat
on the ground out of the way.
Remove any dirt or debris from the
studs, mounting surfaces, and
wheel.
10. Install the spare tyre onto the
studs of the hub.
11 . Tighten the lug nuts with your fin-
gers onto the studs with the small-
er end of the lug nuts closest to
the wheel.
12. Lower the vehicle to the ground
by turning the jack handle coun-
terclockwise.
OAC3079027TU
13. Use the wheel lug nut wrench to
tighten the lug nuts in the order
shown. Double-check each lug
nut until they are tight. After
changing tyres, we recommend
that a HYUNDAI authorised
repairer tighten the lug nuts to
their proper torque as soon as
possible. 7KH ZKHHO OXJ QXW
VKRXOG EH WLJKWHQHG WR a
NJIPaOEIIW

7-21
07
If you have a tyre gauge, check the
tyre pressure (see “Tyres and
Wheels” in chapter 2 for tyre pressure
instructions.). If the pressure is lower
or higher than recommended, drive
slowly to the nearest service station
and adjust it to the recommended
pressure. Always reinstall the valve
cap after checking or adjusting tyre
pressure. If the cap is not replaced,
air may leak from the tyre. If you lose
a valve cap, buy another and install it
as soon as possible. After changing
tyres, secure the flat tyre and return
the jack and tools to their proper stor-
age locations.
NOTICE

7-22
Emergency situations
When driving with the compact spare
tyre mounted to your vehicle:

7-23
07
-DFNODEHO
The actual Jack label in the vehicle
may differ from the illustration.
For more detailed specifications,
refer to the label attached to the jack.
1. Model Name
2. Maximum allowable load
3. When using the jack, set your park-
ing brake.
4. When using the jack, stop the
engine.
5. Do not get under a vehicle that is
supported by a jack.
6. The designated locations under
the frame7. When supporting the vehicle, the
base plate of jack must be vertical
under the lifting point.
8. Shift into R (Reverse) gear on vehi-
cles with Manual transmission or
move the shift lever to the N
(Neutral) position on vehicles with
Automated manual transmission.
9. The jack should be used on firm
level ground.
10. Jack manufacture
11. Production date
12. Representative company and
address
OHYK065011

7-24
Emergency situations
(&'HFODUDWLRQRIFRQIRUPLW\IRU-DFN
JACKDOC14S