2018 MAZDA MODEL CX-9 display

•The Smart City Brake Support (SCBS)
has operated.
•When traveling on a downslope for a
long period of time.
•There is a problem with the system.
•The engine has stalled.
•The electric parking brake (EPB) is
automatically applied during stop hold
control.
•The radar sensor (front) cannot detect
target objects (during rain, fog, snow or
other inclement weather conditions, or
when the radiator grille is dirty).
Resuming control
If the MRCC with Stop & Go function
system is canceled, you can resume
control at the previously set speed by
pressing the RES switch and after all of
the operation conditions have been met.
NOTE
If the set speed is not indicated in the
display, the control does not resume even
if the RES switch is pressed.
Turning off the system
Press the OFF/CAN switch two times
while the MRCC with Stop & Go function
system is operating to switch off the
system.
When Driving
i-ACTIVSENSE
4-118
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38

▼Stop Hold Control
While in headway control using the MRCC with Stop & Go function
system, your vehicle
will stop when a vehicle ahead stops. When the vehicle is stopp ed and the stop hold control
operates, the MRCC with Stop & Go function indicator light turn s on.
NOTE
•If the MRCC with Stop & Go function system is canceled during stop hold control, the
vehicle is held in its stopped position. The stop hold control can be canceled by
performing one the following actions.
•Press the accelerator pedal and resume driving the vehicle.
•While forcefully depressing the brake, switch the MRCC with Stop & Go function
system off.
•The electric parking brake (EPB) is automatically applied and the vehicle is held in its
stopped position when 10 minutes have elapsed since the stop hold control operated. At
this time, the MRCC with Stop & Go function system is canceled.
•The brake lights turn on during stop hold control.
To resume driving
After the vehicle ahead starts moving while your vehicle is sto pped under stop hold control,
press the RES switch or depress the accelerator pedal to cancel the stop hold control and
resume driving.
NOTE
•When you resume driving by pressing the RES switch, your vehicle does not start moving
until the distance between your vehicle and the vehicle ahead lengthens to the specified
distance or farther.
•If the MRCC with Stop & Go function is temporarily canceled during stop hold control,
you cannot resume driving by pressing the RES switch when there are no vehicles in front
of your vehicle. Depress the accelerator pedal and resume driving the vehicle.
Resume driving information
If you do not resume driving with in a few seconds after the vehicle ahead starts moving, the
multi-information display vehicle-ahead indication flashes to u rge the driver to resume
driving.
When Driving
i-ACTIVSENSE
4-119
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38

▼Cruise Control Function
While this function is operating, the
headway control operation is canceled and
only the cruise control function operates.
The vehicle speed can be set more than
about 25 km/h (16 mph).
Use the cruise c
ontrol function on
expressways and other highways which do
not require a lot of repeated acceleration
and deceleration.
WA R N I N G
Do not use the cruise control function in
the following locations:
Otherwise, it could lead to an accident.
 Roads with sharp curves and where
vehicle traffic is heavy and there is
insufficient space between vehicles.
(Driving under these conditions using the
cruise control function is not possible)
 Steep down slopes (Set speed may be
exceeded because sufficient engine
braking cannot be applied)
 Slippery roads such as ice or snow-bound
roads (Tires could spin causing you to
lose vehicle control)
Always drive carefully:
The warnings and brake control will not
operate after the headway control function
is canceled and the system is switched to
only the cruise control function. Depress
the brake pedal to decelerate according to
the surrounding condit ions while keeping a
safer distance from the vehicle ahead and
always driving carefully.
Switching to cruise control function
When the MODE switc h is pressed until
the system switches to the cruise main
indication (white) wh ile the MRCC with
Stop & Go function system is turned on,
the system switches to the cruise control
function.
When the system switches to the cruise
control function, the indicator and
multi-information disp lay notify the driver
as follows:
•The MRCC with Stop & Go function set
indication (green) or the MRCC with
Stop & Go function main indication
(white) is turned off, and the cruise main
indication (white) is turned on.
•A message is displayed in the
multi-information display.
WA R N I N G
Always turn off the cruise control function
when it is not in use:
Leaving the cruise control function turned
on when it is not in use is dangerous as it
could operate unexpectedly, resulting in an
accident.
How to set the speed
Adjust the system to the desired vehicle
speed using the accelerator pedal.
When the SET
or SET switch is
pressed, the cruise se t indication (green) is
turned on and headway control begins.
When Driving
i-ACTIVSENSE
4-120
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38

▼System Operation
Make sure that the LAS&LDWS OFF
switch indicator light is turned off. When
the LAS&LDWS OFF s
witch indicator
light is turned on, press the switch and
make sure that the switch indicator light
turns off.
Indicator light
The LAS&LDWS indic ation (white) is
displayed in the multi-information display,
and the system goes on stand-by.
(White)
Drive the vehicle in the center of the
vehicle lane while the system is on
standby. When all of the following
conditions are met, the LAS&LDWS
indication (green) is displayed in the
multi-information display, and the system
becomes operational.
(Green)
•The engine is running.
•The vehicle speed is about 60 km/h (37
mph) or faster.
•The system detects w hite (yellow) lane
lines on both the right and left sides.
•The driver is operating the steering
wheel.
•The driving lane is neither narrow nor
wide.

NOTE
The LAS&LDWS indication is white when
the system detects only a white (yellow)
line on either the left or right, and the
indication changes to green when the
system detects white (yellow) lines on both
the left and right sides.
Detection only on either left or right Detects on both
left and right sides
(White) (Green)
When Driving
i-ACTIVSENSE
4-126
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38

The LAS&LDWS goes on stand-by status
in the following cases:
•The system cannot detect white (yellow)
lane lines.
•The vehicle speed is less than about 60
km/h (37 mph).
•The ABS/TCS is operating.
•The TCS is turned off.
(If the TCS is turned off while the
system is operational, a warning beep is
heard and the system goes on standby.)
•The vehicle is making a sharp curve.
•The brake pedal is depressed.
•The steering wheel is operated abruptly.
•The width of a lane is excessively
narrow or wide.
NOTE
•The LAS&LDWS does not operate until
the system detects white (yellow) lane
lines on either the left or right.
•When the system detects a white
(yellow) lane line on one side only, the
system will not operate the steering
wheel operation assist and the warning
for the lane line on the side that is not
being detected. The steering wheel
operation assist and the warning is only
for a lane deviation on the side that is
being detected.
•If the driver takes his or her hands off
the steering wheel (not holding the
steering wheel), the warning sound is
activated and an alert is indicated in the
multi-information display or the active
driving display.

Active Driving Display Multi-information Display
If the steering wheel is held lightly, or
depending on the road conditions, the
system may detect that you have
released the steering wheel (not holding
the steering wheel) even if you are
holding it, and display a message in the
multi-information di splay or the active
driving display.
•The timing at which the lane departure
warning is activated and the steering
wheel operation assist is performed
varies.
•The following settings for the
LAS&LDWS can be changed. Refer to
Personalization Features on page 9-
11 .
•Steering operation assist operational/
non-operational
•Cancel sensitivity (likelihood of
steering assist)
When Driving
i-ACTIVSENSE
4-127
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38

Vehicle lane line display
When the LAS&LDWS becomes
operational while on standby, the vehicle
lane lines are displayed in the
multi-information display and the active
driving display. In the vehicle lane lines
display indicating the operation status, the
color of the vehicle lane lines being
detected changes to white.
(Stand-by status)
Multi-information Display
Active Driving Display
(Operational status)
Multi-information Display
Active Driving Display
Auto cancel
In the following cases, the LAS&LDWS is
automatically canceled, the LAS&LDWS
warning indication (amber) turns on, and
an alert is displayed. When the
LAS&LDWS become operational, the
system turns back on automatically.
•The temperature inside the camera is
high or low.
•The windshield around the camera is
foggy.
•The windshield around the camera is
blocked by an obstruction, causing poor
forward visibility.
Auto cancel of warning/steering assist
When the following operations are
performed, the LAS& LDWS operation is
canceled automatically. The LAS&LDWS
resumes automatically after the operation.
•The steering wheel is operated abruptly.
•The brake pedal is operated.
•The accelerator pedal is operated.
(To cancel the automatic sensitivity
cancel function, deselect “Cancel
sensitivity” in the personalization
features setting.)
•The turn signal lever is operated.
•The vehicle crosses a lane line.
NOTE
•After the operation, the LAS&LDWS
operation may not operate for a period
of 5 seconds at the most until the lane
lines are detected.
•Under the following conditions, the
LAS&LDWS cancels the warning/
steering assist automatically.
When Driving
i-ACTIVSENSE
4-128
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38

•The driver takes his/her hands off the
steering wheel.
(The LAS&LDWS is designed to assist
the driver's steering operation and it
will resume operation automatically
when the driver holds the steering
wheel.)
•The TCS OFF switch is pressed to
cancel the TCS.
Steering operation assist OFF
(non-operational)
The steering operation assist for the
LAS&LDWS can be changed to
non-operational (OFF).
Refer to Setting Cha nge (Personalization
Features) on page 9-11.
When the steering operation assist has
been changed to non-operational (OFF),
the operation conditions and the display of
the LAS&LDWS differ. Operate the
system as follows:
System operation
Make sure that the LAS&LDWS OFF
switch indicator light is turned off. When
the LAS&LDWS OFF switch indicator
light turns on, press the switch and make
sure that the switch i ndicator light turns
off.
Indicator light
Drive the vehicle in the center of the
driving lane while the LAS&LDWS OFF
switch indicator light is turned off.
The system becomes operational when all
of the following conditions are met.
•The system detects white (yellow) lane
lines on both the right and left sides or
on either side.
•The vehicle speed is about 60 km/h (37
mph) or faster.
•The vehicle is driven on a straight road
or road with gentle curves.
•The engine is running.
The LAS&LDWS goes on stand-by status
in the following cases:
•The system cannot detect white (yellow)
lane lines.
•The vehicle speed is less than about 60
km/h (37 mph).
•The vehicle is making a sharp curve.
•The vehicle is making a curve at an
inappropriate speed.
NOTE
•The LAS&LDWS remains on stand-by
until it detects white (yellow) lines on
both the left and right sides, or on either
side.
•When the system detects a white
(yellow) lane line on one side only, the
system will not activ ate warnings for the
lane line on the side that is not being
detected.
•The distance and warning sensitivity
(likelihood of a warning) which the
system uses to determine the possibility
of a lane departure can be changed.
Refer to Setting Change
(Personalization Features) on page 9-
11 .
When Driving
i-ACTIVSENSE
4-129
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38

Vehicle lane line display
When the LAS&LDWS becomes
operational while on standby, the vehicle
lane lines are displayed in the
multi-information display. The system
changes to operational status display when
the system detects a white (yellow) line on
either the left or right.
(Stand-by status)
(Operational status)
Auto cancel
In the following cases, the LAS&LDWS is
automatically canceled, the LAS&LDWS
warning indication (amber) turns on, and
an alert is displayed. When the
LAS&LDWS become operational, the
system turns back on automatically.
•The temperature inside the camera is
high or low.
•The windshield around the camera is
foggy.
•The windshield around the camera is
blocked by an obstruction, causing poor
forward visibility.
(Auto cancel of warnings)
When the following operations are
performed, the LAS&LDWS determines
that the driver intends to make a lane
change and the system operation is
canceled automatically. The LAS&LDWS
resumes automatically after the operation.
•The steering wheel is operated abruptly.
•The brake pedal is depressed.
•The accelerator pedal is depressed.
(To cancel the automatic sensitivity
cancel function, deselect “Warning
sensitivity” in the personalization
features setting.)
•The turn signal lever is operated.
•The vehicle crosses a lane line.
▼System Canceling
When the LAS&LDWS is turned off,
press the LAS&LDWS OFF switch.
Indicator light
The LAS&LDWS OFF switch indicator
light turns on.
NOTE
•In the following ca
ses, the LAS&LDWS
is canceled automatically and the
LAS&LDWS OFF indication is
displayed in the multi-information
display. Have your vehicle inspected at
an Authorized Mazda Dealer.
When Driving
i-ACTIVSENSE
4-130
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38