2018 Lexus LC500 wheel

329
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
Vehicles with front and rear tires of
the same size
Vehicles with front and rear tires of
differing sizes
To equalize tire wear and help extend tire
life, Lexus recommends that tire rotation is
carried out approximately every 10000
km (6000 miles).
Do not fail to initialize the tire pressure
warning system after tire rotation.
■When rotating the tires
Make sure that the engine switch is off. If the tires are rotated while
the engine switch is in IGNITION ON mode , the tire position information will not be updated.
If this accidentally occurs, either turn the engine switch to off and then to IGNITION ON mode ,
or initialize the tire pr essure warning system after checking that the tire pressure is prop-erly adjusted.
When run-flat tires are installed, the
vehicle can be driven for a maximum of
160 km (100 miles) at a speed below
80 km/h (50 mph) after any tire goes
flat. (However, the vehicle speed may
not increase to near 80 km/h [50
mph] depending on weather or driving
conditions.)
A run-flat tire has a mark on
the side wall.
Make sure to replace the flat tire before the
vehicle has been driven for near 160 km
(100 miles). Also, do not use a repaired
tire.
■Run-flat tires
●The run-flat tires are for only this vehicle. Do not use the tires on other vehicles.
●Do not mix run-flat tires and normal tires.
●If non-genuine Lexus wheels are used, it
may be impossible to sufficiently demon- strate the performanc e of run-flat tires.
Your vehicle is equipped with a tire
pressure warning system that uses tire
pressure warning valves and transmit-
ters to detect low tire inflation pressure
before serious problems arise.
 If the tire pressure drops below a
predetermined level, the driver is
warned by a screen display and a
warning light. ( P.374)
 The tire pressure detected by the
tire pressure warning system can be
displayed on the multi-information
Run-flat tires
Tire pressure warning system

330
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
display. (P.92)
The illustration used is intended as an
example, and may differ from the image
that is actually displayed on the multi-infor-
mation display.
■Routine tire inflation pressure checks
The tire pressure warning system does not
replace routine tire inflation pressure checks. Make sure to check tire inflation pressure as part of your routine of daily
vehicle checks.
■Situations in which the tire pressure warning system may not operate prop-
erly
●In the following cases, the tire pressure
warning system may not operate prop- erly.• If non-genuine Lexus wheels are used.
• A tire has been replaced with a tire that is not an OE (Original Equipment) tire.• A tire has been replaced with a tire that is
not of the specified size. • Tire chains etc. are equipped.• An auxiliary-supported run-flat tire is
equipped. • If a window tint that affects the radio wave signals is installed.
• If there is a lot of snow or ice on the vehi- cle, particularly around the wheels or wheel housings.
• If the tire inflation pressure is extremely higher than the specified level.• If wheels without tire pressure warning
valves and transmitters are used. • If the ID code on the tire pressure warn-ing valves and transmitters is not regis-
tered in the tire pressure warning
computer.
●Performance may be affected in the fol-
lowing situations. • Near a TV tower, electric power plant, gas station, radio station, large display,
airport or other facility that generates strong radio waves or electrical noise• When carrying a portable radio, cellular
phone, cordless phone or other wireless communication device
If tire position information is not correctly
displayed due to the radio wave conditions,
the display may be corrected by driving and
changing the radio wave conditions.
●When the vehicle is parked, the time taken for the warning to start or go off
could be extended.
●When tire inflation pressure declines rap-
idly for example when a tire has burst, the warning may not function.
■Warning performance of the tire pres-sure warning system
The warning of the tire pressure warning system will change in accordance with the
conditions under which it was initialized. For this reason, the system may give a warning
even if the tire pressure does not reach a low enough level, or if the pressure is higher than the pressure that was adjusted to when
the system was initialized.

335
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
When replacing tires or wheels, tire
pressure warning valves and transmit-
ters must also be installed.
When new tire pressure warning
valves and transmitters are installed,
new ID codes must be registered in the
tire pressure warning computer and
the tire pressure warning system must
be initialized. ( P.337)
■When replacing the tires and wheels
If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work
properly. After driving for about 10 minutes, the tire pressure warning light blinks for 1 minute and stays on to indicate a system
malfunction.
■The tire pressure warning system
must be initialized in the following
circumstances:
 When rotating the tires.
 When the tire inflation pressure is
changed when changing traveling
speed.
 When the tire inflation pressure is
changed such as when changing tire
size. (When there are multiple spec-
ified pressures)
 After registering the ID codes.
( P.337)
When the tire pressure warning system
is initialized, the current tire inflation
pressure is set as the benchmark pres-
sure.
■How to initialize the tire pressure
warning system
1 Park the vehicle in a safe place and
turn the engine switch switch> off.
Initialization cannot be performed while the vehicle is moving.
2 Adjust the tire inflation pressure to
the specified cold tire inflation pres-
sure level.
Make sure to adjust the tire pressure to the specified cold tire infl ation pressure level. The tire pressure warning system will oper-
ate based on this pressure level.
3 Turn the engine switch switch> to IGNITION ON mode
.
Installing tire pressure warning
valves and tr ansmitters
NOTICE
■Repairing or replacing tires, wheels, tire pressure warning valves, trans-
mitters and tire valve caps
●When removing or fitting the wheels,
tires or the tire pressure warning valves and transmitters, contact any
authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer as the tire pressure warning
valves and transmitters may be dam- aged if not handled correctly.
●Make sure to install the tire valve caps. If the tire valve caps are not installed,
water could enter the tire pressure warning valves and the tire pressure warning valves could be bound.
●When replacing tire valve caps, do not
use tire valve caps other than those specified. The cap may become stuck.
Initializing the tire pressure
warning system

337
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
pressure warning light does not blink 3 times. (Initialization will not occur while driving)
●After performing init ialization, the tire pressure warning light blinks for 1 minute
then stays on after driving for about 20 minutes.
If the inflation pressure of each tire is still not
displayed, have the vehicle inspected by
any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer.
■When registering ID codes
●Initialize the tire pressure warning system after ID code registra tion. Initialization is
disabled if the system was initialized before registration.
●After ID code registration, the tires are hot by driving. Initia lize the tire pressure warning system after the tires become
cold.
The tire pressure warning valve and
transmitter is equipped with a unique
ID code. When replacing a tire pres-
sure warning valve and transmitter, it is
necessary to register the ID code.
When registering the ID codes, per-
form the following procedure.
1 Turn the engine switch switch> to IGNITION ON mode
.
2 Press or of the meter con-
trol switches and select .
3 Press or of the meter con-
trol switches and select “Vehicle
Settings”, and then press “OK”.
4 Press or of the meter con-
trol switches and select “TPWS
SET”, and then press “OK”.
5 Press or of the meter con-
trol switches and select “Change
wheel set”, and then press and hold
“OK” until the tire pressure warning
light starts blinking.
The change wheel set mode is activated and registration is started.
A message is displayed on the multi-infor- mation display, and “--” is displayed for inflation pressure of e ach tire. Then, the tire
pressure warning light blinks rapidly for approximately 1 minute and stays on.
6 Drive the vehicle at 40 km/h
(25mph) or more for approxi-
mately 10 to 30 minutes.
When registration is completed, the tire pressure warning light will go off and the inflation pressure of each tire will be dis-
played on the multi-information display.
WARNING
■When initializing the tire pressure
warning system
Do not initialize tire inflation pressure
without first adjusting the tire inflation pressure to the specified level. Other-wise, the tire pressure warning light may
not come on even if the tire inflation pres- sure is low, or it may come on when the tire inflation pressure is actually normal.
Registering ID codes

338
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
The time elapsed before registration is completed differs according to the driving condition and environment.
■Canceling the change wheel set mode
●If turning the engine switch off when in the change wheel set
mode before driving, the change wheel set mode is canceled.
●After driving when in the change wheel set mode, the change wheel set mode cannot be canceled. To cancel the mode,
perform the procedure for ID code regis- tration again and turn the engine switch off before driving.
●If the change wheel set mode is canceled, the ID codes that have already been reg-
istered are communicated. When com- munication is finished, the tire pressure warning light will turn off.
■When ID code registration may not
operate properly
●Do not move the vehicle backward
during registration. Registration is started again from the beginning and it may take longer than usual.
●When another vehicle is running the side of the vehicle such as in heavy traffic, it
may take longer to detect the vehicle’s tire pressure warning valves and trans-mitters.
●If tire pressure warning valves and trans-mitters are in the vehicle, the ID codes
may not be registered.
If registration takes long time, perform the
procedure for ID code registration again
after parking the vehicle for 20 minutes.
If the ID codes cannot be registered even
when performing the above procedure,
contact any authorized Lexus retailer or
Lexus authorized repairer, or any reliable
repairer.

339
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
Stop the vehicle in a safe place on a
hard, flat surface.
 Set the parking brake.
 Shift the shift position to P.
 Turn off the intrusion sensor and tilt
sensor ( P.78)
 Stop the engine .
Screwdriver
Wheel nut wrench
Jack
Jack handle
Towing eyelet
Replacing the tire
When raising your vehicle with a
jack, position the jack correctly.
Improper placement may damage
your vehicle or cause injury.
If necessary tire replacement
seems difficult to perform, contact
any authorized Lexus retailer or
Lexus authorized repairer, or any
reliable repairer.
Before jacking up the vehicle
Location of the jack and tools
A
B
C
D
E

341
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
2Slightly loosen the wheel nuts (one
turn).
3 Turn the tire jack portion by
hand until the notch of the jack is in
contact with the jack point.
The jack point guides are located under the rocker panel. They indicate the jack
point positions.
4 Raise the vehicle until the tire is
slightly raised off the ground.
5 Remove all the wheel nuts and the
tire.
When resting the tire on the ground, place
the tire so that the wheel design faces up to avoid scratching the wheel surface.
1 Remove any dirt or foreign matter
from the wheel contact surface.
TireWheel chock positions
Front left-
hand side
Behind the rear right-hand
side tire
Front right-
hand side
Behind the rear left-hand
side tire
Rear left-
hand side
In front of the front right-
hand side tire
Rear right-
hand side
In front of the front left-hand
side tire
A
WARNING
■Replacing a tire
Do not touch the disc wheels or the area around the brakes immediately after the vehicle has been driven.
After the vehicle has been driven the disc wheels and the area around the brakes will be extremely hot. Touching these
areas with hands, feet or other body parts while changing a tire, etc. may result in burns.
Installing the tire

342
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
If foreign matter is on the wheel contact surface, the wheel nuts may loosen while the vehicle is in motion, causing the tire to
come off.
2 Install the tire and loosely tighten
each wheel nut by hand by approxi-
mately the same amount.
Turn the wheel nuts until the washers come
into contact with the disc wheel.
Disc wheel
Washer
3 Lower the vehicle.
4 Firmly tighten each wheel nut two
or three times in the order shown in
the illustration.
Tightening torque: 140 N•m (14.3 kgf•m, 103.3 ft•lbf)
5 Stow the jack and all tools.
A
B