2018 Lexus LC500 sensor

265
4
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Driving
■EPS, VGRS and DRS operation sound
When the steering wheel is operated, a
motor sound (whirring sound) may be heard. This does not indicate a malfunction.
■Automatic reactivation of TRC and VSC systems
After turning the TRC and VSC systems off, the systems will be automatically re-
enabled in the following situations:
●When the engine switch
is turned off
●If only the TRC system is turned off, the
TRC will turn on when vehicle speed increases
If both the TRC and VSC systems are turned off, automatic re-enabling will not occur when vehicle speed increases.
■Secondary Collision Brake operating
conditions
The vehicle speed is approximately 10 km/h
(6 mph) or more and the airbag sensor detects a collision. (The Secondary Colli-sion Brake will not operate when the vehicle
speed is below approximately 10 km/h [6 mph].)
■Secondary Collision Brake automatic
cancellation
The Secondary Collision Brake is automati-
cally canceled in the following situations:
●The vehicle speed drops below approxi-
mately 10 km/h (6 mph)
●A certain amount of time elapses during
operation
●The accelerator pedal is depressed a
large amount
■If “Check Secondary Collision Brake system” is displayed on the multi-infor-mation display
The system may be malfunctioning. Have the vehicle inspected at any authorized
Lexus retailer or Lexus authorized repairer, or any reliable repairer.
■Reduced effectiveness of the EPS sys-tem
The effectiveness of the EPS system is
reduced to prevent the system from over- heating when there is frequent steering input over an extended period of time. The
steering wheel may feel heavy as a result. Should this occur, refrain from excessive steering input or stop the vehicle and turn
the engine off. The EPS sys- tem should return to normal within 10 min-utes.
■Operating conditions of emergency
brake signal
When the following three conditions are
met, the emergency brake signal will oper- ate:
●The emergency flashers are off.
●Actual vehicle speed is over 55 km/h
(35 mph).
●The brake pedal is depressed in a manner
that cause the system to judge from the vehicle deceleration that this is a sudden braking operation.
■Automatic system cancelation of emer-
gency brake signal
The emergency brake sign al will turn off in
any of the following situations:
●The emergency flashers are turned on.
●The brake pedal is released.
●The system judges from the vehicle deceleration that is not a sudden braking
operation.
WARNING
■The ABS does not operate effectively when
●The limits of tire gripping performance have been exceeded (such as exces-
sively worn tires on a snow covered road).
●The vehicle hydroplanes while driving at high speed on wet or slick roads.

286
-$@-$I@0.@0.&@ &&

5-3. Using the air conditioning system
2Press the outside/recirculated air
mode switch to switch to automatic
air intake mode.
The air conditioning system automatically
switches between outside air and recircu-
lated air modes.
3Adjust the temperature setting.
4 To stop the operation, press the off
switch or select “Off” on the sub
function menu. ( P.283)
If the fan speed setting or air flow
modes are operated, the automatic
mode indicator goes off. However,
automatic mode for functions other
than that operated is maintained.
■Using automatic mode
Fan speed is adjusted automatically accord-
ing to the temperature setting and the
ambient conditions.
Therefore, the fan may stop for a while until
warm or cool air is ready to flow immedi-
ately after the automatic mode switch is
pressed or “AUTO” is selected.
Cool air may blow around the upper body
even when the heater is on due to sunlight.
■Windshield fog detection function
When automatic mode is set, the humidity
sensor detects fog on the windshield and
controls the air conditioning system to pre-
vent fog.
■Automatic mode for air intake control
In automatic mode, the system detects
exhaust gas and other pollutants and auto-
matically switches between outside air and
recirculated air modes.
When the dehumidification function is off,
and the fan is operating, turning automatic
mode on will activate the dehumidification
function.
To turn on the “DUAL” mode, perform
any of the following procedures:
 Select “DUAL” on the sub function
menu. ( P.283)
 Select “DUAL” on the option con-
trol screen.
 Adjust the passenger’s side tem-
perature setting.
The indicator on the main control screen
comes on when the “DUAL” mode is on.
NOTICE
■Humidity sensor
In order to detect fog on the windshield,
a sensor which monitors the temperature
of the windshield, the surround humidity,
etc. is installed.
Follow these points to avoid damaging
the sensor:
●Do not disassemble the sensor
●Do not spray the glass cleaner on the
sensor or subject it to strong impacts
●Do not stick anything on the sensor
Adjusting the temperature for
driver and passenger seats sepa-
rately (“DUAL” mode)

305
6
-$@-$I@0.@0.&@ &&

6-1. Maintenance and care
Maintenance and care
■Notes for a smart entry & start system
If the door handle becomes wet while the
electronic key is within the effective range, the door may lock and unlock repeatedly. In that case, follow the following correction
procedures to wash the vehicle:
●Place the key in a position 2 m (6 ft.) or
more separate from the vehicle while the vehicle is being washed. (Take care to ensure that the key is not stolen.)
●Set the electronic key to battery-saving mode to disable the smart entry & start
system. ( P.124)
■Aluminum wheels
●Remove any dirt immediately by using a
neutral detergent.
●Wash detergent off with water immedi-
ately after use.
●To protect the paint from damage, make
sure to observe the following precau- tions.• Do not use acidic, alkaline or abrasive
detergent • Do not use hard brushes• Do not use detergent on the wheels when
they are hot, such as after driving or park- ing in hot weather
■Brake caliper coating
●When using detergent, use neutral deter-gent. Do not use hard brushes or abra-
sive cleaners, as they will damage the coating.
●Do not use detergent on the brake cali-pers when they are hot.
●Wash detergent off immediately after use.
■Bumpers
Do not scrub with abrasive cleaners.
■Front side windows water-repellent coating
●The following precautions can extend the effectiveness of the water-repellent coat-ing.
• Remove any dirt, etc. from the front side windows regularly.• Do not allow dirt and dust to accumulate
on the windows for a long period. Clean the windows with a soft, damp cloth as soon as possible.
• Do not use wax or glass cleaners that contain abrasives when cleaning the win-dows.
• Do not use any metallic objects to remove condensation build up.
●When the water-repellent performance has become insufficient, the coating can be repaired. Contact any authorized
Lexus retailer or Lexus authorized repairer, or any reliable repairer.
WARNING
■When washing the vehicle
Do not apply water to the inside of the
engine compartment. Doing so may cause the electrical components etc. to catch fire.
■When cleaning the windshield
Set the wiper switch to off. If the wiper switch is in AUTO, the wipers
may operate unexpectedly in the follow- ing situations, and may result in hands being caught or other serious injuries
and cause damage to the wiper blades.
Off
AUTO
●When the upper part of the windshield where the raindrop sensor is located is
touched by hand
●When a wet rag or similar is held close to the raindrop sensor
●If something bumps against the wind-shield
A
B

306
-$@-$I@0.@0.&@ &&

6-1. Maintenance and care
WARNING
●If you directly touch the raindrop sen- sor body or if something bumps into the raindrop sensor
■Precautions regarding the exhaust
pipes and rear bumper diffusers
As exhaust gases cause the exhaust
pipes and rear bumper diffusers to become quite hot, do not touch the exhaust pipes and rear bumper diffusers
while the engine is running or immediately after the engine is turned off.
When washing the vehicle, be careful not to touch the exhaust pipes and rear
bumper diffusers until they have cooled sufficiently, as touching hot exhaust pipes and rear bumper diffusers can cause
burns.
■Precaution regarding the rear bumper with Blind Spot Monitor (if equipped)
If the paint of the rear bumper is chipped or scratched, the system may malfunc-
tion. If this occurs, consult any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer.
NOTICE
■Application of coatings to the vehicle body (vehicles with CFRP parts)
Do not apply any kind of coating to the vehicle body as doing so may damage
the paint or reduce its durability.
■To prevent paint deterioration and corrosion on the body and compo-
nents (aluminum wheels etc.)
●Wash the vehicle immediately in the
following cases:
• After driving near the sea coast
• After driving on salted roads
• If coal tar, pollen or tree sap is present on the paint surface
• If dead insects, insect droppings or bird droppings are present on the paint surface
• After driving in an area contaminated with soot, oily smoke, mine dust, iron
powder or chemical substances
• If the vehicle becomes heavily soiled
with dust or mud
• If liquids such as benzene and gasoline
are spilled on the paint surface
●If the paint is chipped or scratched, have it repaired immediately.
●To prevent the wheels from corroding, remove any dirt and store in a place
with low humidity when storing the wheels.
■Cleaning the exterior lights
●Wash carefully. Do not use organic substances or scrub with a hard brush.
This may damage the surfaces of the lights.
●Do not apply wax to the surfaces of the lights.
Wax may cause damage to the lenses.
■When using an automatic car wash
Set the wiper switch to the off position.
If the wiper switch is in AUTO, the wipers may operate and the wiper blades may be damaged.

339
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
Stop the vehicle in a safe place on a
hard, flat surface.
 Set the parking brake.
 Shift the shift position to P.
 Turn off the intrusion sensor and tilt
sensor ( P.78)
 Stop the engine .
Screwdriver
Wheel nut wrench
Jack
Jack handle
Towing eyelet
Replacing the tire
When raising your vehicle with a
jack, position the jack correctly.
Improper placement may damage
your vehicle or cause injury.
If necessary tire replacement
seems difficult to perform, contact
any authorized Lexus retailer or
Lexus authorized repairer, or any
reliable repairer.
Before jacking up the vehicle
Location of the jack and tools
A
B
C
D
E

370
-$@-$I@0.@0.&@ &&

7-2. Steps to take in an emergency
■Electric power steering system warning light (warning buzzer)
■PCS warning light
Warning
lightWarning light/Details/Actions
(red)
or
(yellow)
Indicates a malfunction in the EPS (Electric Power Steering) system
 Have the vehicle inspected by any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer immediately.
Warning
lightWarning light/Details/Actions
 When the warning light flashes (and a buzzer sounds):
Indicates a malfunction in the PCS
 Have the vehicle inspected by any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer immediately.
 When the warning light flashes (and a buzzer does not sound):
Indicates that the PCS is temporarily unavailable, possibly due to either of
the following:
 An area around the radar sensor or camera sensor being dirty or covered
with condensation, ice, stickers, etc.
 Clear the dirt, condensation, ice, stickers, etc. (P.208)
 Radar sensor or camera sensor operational conditions (such as tempera-
ture etc.) being not met
 Driving is possible in this case. The PCS will be enabled if the opera-
tional conditions (such as temperature etc.) are met again.
 When the warning light is illuminated:
Either the VSC system or PCS is disabled or both are disabled.
 To enable the PCS, enable both the VSC system and PCS. (P.212,
263)

375
7
-$@-$I@0.@0.&@ &&

7-2. Steps to take in an emergency
When trouble arises
■High coolant temperature warning light (warning buzzer)*
*: This light illuminates on the multi-information display.
■Front passenger detection sensor, seat belt reminder and warning buzzer
●If luggage is placed on a front passenger seat, the front passenger detection sensor may cause the warning light to flash and the warning buzzer to sound even if a passenger is not
sitting in the seat.
●If a cushion is placed on the seat, the sensor may not detect a passenger, and the warning
light may not operate properly.
■If the malfunction indicator lamp comes on while driving
The malfunction indicator lamp w ill come on if the fuel tank becomes completely empty. If
the fuel tank is empty, refuel the vehicle immediately. The malfunction indicator lamp will go off after several trips.
If the malfunction indicator lamp does not go off, contact any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer as soon as possible.
■Electric power steering system warning light (warning buzzer)
When the 12-volt battery charge becomes insufficient or the voltage temporarily drops, the electric power steering system warning lig ht may come on and the warning buzzer may sound.
■Tire pressure warning light
When a malfunction occurs in the tire pressure warning system, the tire pressure warning light blinks to warn the driver. However, if the warning light blinks for 1 minute, and then
remains illuminated, maki ng it difficult to determine whether the warning light is blinking, turn the engine switch fr om off to IGNITION ON mode and check if the warning light blinks.
■When the tire pressure warning light comes on
Carry out the following procedure after the tire temperature has lowered sufficiently.
●Check the tire inflation pressure and adjust to the appropriate level.
●If the warning light does not go out even after several minutes, check that the tire inflation
pressure is at the specified level and carry out initialization. ( P.335)
The warning light may come on again if the above operations are conducted without first
allowing the tire temperature to lower sufficiently.
■The tire pressure warning light may come on due to natural causes
The tire pressure warning light may come on du e to natural causes such as natural air leaks
and tire inflation pressure changes caused by temperature. In this case, adjusting the tire inflation pressure will turn off the warning light (after a few minutes).
Warning
lightWarning light/Details/Actions
Indicates that the engine coolant temperature increases
 Stop and check. (P.400, 403)

425
8
-$@-$I@0.@0.&@ &&

8-2. Customization
Vehicle specifications
*1: For details about each function: P.88, 96
*2: The default setting varies according to country.
*3:LC500
*4:LC500h
*5: 2 of the following items: current fuel consumption, average fuel economy (after reset),
average fuel economy (after start), average fuel economy (after refuel), average vehicle
speed (after reset), average vehicle speed (after start), elapsed time (after reset),
elapsed time (after start), distance (driving range), distance (after start), blank.
*6: Refer to the “NAVIGATION SYSTEM OWNER’S MANUAL”.
Accent colorColor 1Color 2O*6O—
Rev indicatorOffOn—O—
Rev indicator red zone setting5000 r/min.*3
4000 r/min.*4
2000 - 7300
r/min.*3
2000 - 6600
r/min.*4
—O—
Rev peakOffOn—O—
Clock24-hour dis-
play12-hour display—O—
Sensor sensitivity for darkening the
brightness of the instrument cluster
depending on the outside bright-
ness
Standard-2 to 2——O
Sensor sensitivity for returning the
brightness of the instrument cluster
to the original level depending on
the outside brightness
Standard-2 to 2——O
Suggestion functionOn
On
(when the vehicle is
stopped)O—O
Off
Function*1Default settingCustomized settingABC