2018 Lexus LC500 buttons

57
1
-$@-$I@0.@0.&@ &&

1-2. Child safety
For safety and security
locking feature), secure the child
restraint system using a locking clip.
5 After installing the child restraint
system, rock it back and forth to
ensure that it is installed securely.
( P.57)
■Removing a child restraint system
installed with a seat belt
Press the buckle release button and
fully retract the seat belt.
When releasing the buckle, the child
restraint system may spring up due to the
rebound of the seat cushion. Release the
buckle while holding down the child
restraint system.
Since the seat belt automatically reels itself,
slowly return it to the stowing position.
■When installing a child restraint system
You may need a locking clip to install the child restraint system. Follow the instruc-tions provided by the manufacturer of the
system. If your child restraint system does not provide a locking clip, you can purchase the following item from any authorized
Lexus retailer or Lexus authorized repairer, or any reliable repairer: Locking clip for child restraint system (Part
No. 73119-22010)
■ISOFIX rigid anchors (ISOFIX
child restraint system)
Lower anchors are provided for the
each rear seat. (Buttons displaying the
location of the anchors are attached to
the seats.)
WARNING
■When installing a child restraint sys- tem
Observe the following precautions. Failure to do so may result in death or serious injury.
●Do not allow children to play with the
seat belt. If the seat belt becomes twisted around a child’s neck, it may lead to choking or other serious inju-
ries that could result in death. If this occurs and the buckle cannot be unfastened, scissors should be used to
cut the belt.
●Ensure that the belt and plate are securely locked and the seat belt is not twisted.
●Shake the child restraint system left
and right, and forward and backward to ensure that it has been securely installed.
●After securing a child restraint system,
never adjust the seat.
●When a junior seat is installed, always ensure that the shoulder belt is posi-tioned across the center of the child’s
shoulder. The belt should be kept away from the child’s neck, but not so that it could fall off the child’s shoulder.
●Follow all installation instructions pro-
vided by the child restraint system manufacturer.
Child restraint system fixed with
an ISOFIX rigid anchor

112
-$@-$I@0.@0.&@ &&

3-1. Key information
3-1.Key information
The following keys are provided with
the vehicle.
Electronic keys
• Operating the smart entry & start sys-
tem ( P.122)
• Operating the wireless remote control
function
Mechanical keys
Key number plate
■When riding in an aircraft
When bringing an electronic key onto an aircraft, make sure you do not press any buttons on the electronic key while inside
the aircraft cabin. If you are carrying an electronic key in your bag etc., ensure that the buttons are not likely to be pressed acci-
dentally. Pressing a button may cause the electronic key to emit radio waves that could interfere with the operation of the air-
craft.
■Electronic key battery depletion
●The standard battery life is 1 to 2 years.
●If the battery becomes low, an alarm will sound in the cabin when the engine
is stopped.
●As the electronic key always receives
radio waves, the battery will become depleted even if the electronic key is not
used. The following symptoms indicate that the electronic key battery may be depleted. Replace the battery when nec-
essary. ( P.349) • The smart entry & start system or the wireless remote control does not oper-
ate. • The detection area becomes smaller.• The LED indicator on the key surface
does not turn on.
●To avoid serious deterioration, do not
leave the electronic key within 1 m (3 ft.) of the following electrical appliances that produce a magnetic field:
•TVs •Personal computers• Cellular phones, cordless phones and
battery chargers • Recharging cellular phones or cordless phones
• Table lamps •Induction cookers
■Replacing the battery
 P.349
■Confirmation of the registered key number
The number of keys already registered to the vehicle can be confirmed. Ask any
authorized Lexus retailer or Lexus autho- rized repairer, or any reliable repairer for details.
■If “A New Key has been Registered
Contact Your Dealer for Details” is shown on the multi-information display
This message will be displayed each time the driver’s door is opened when the doors are unlocked from the outside for approxi-
mately 10 days after a new electronic key has been registered. If this message is displayed but you have not
had a new electronic key registered, ask any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer
to check if an unknown electronic key (other than those in your possession) has been registered.
Keys
Key types
A
B
C

116
-$@-$I@0.@0.&@ &&

3-2. Opening, closing and locking the doors and trunk
■Switching the door unlock function
It is possible to set which doors the entry
function unlocks using the wireless remote control.
1 Turn the engine switch off.
2 For vehicles with an intrusion sensor:
Cancel the intrusion sensor and tilt sen- sor of the alarm system to prevent unin-tended triggering of the alarm while
changing the settings. ( P.78)
3 When the indicator light on the key sur-
face is not on, press and hold or
for approximately 5 seconds
while pressing and holding .
The setting changes each time an operation is performed, as shown below. (When changing the setting continuously, release
the buttons, wait for at least 5 seconds, and repeat step 3.)
*1: Left-hand drive vehicles
*2: Right-hand drive vehicles
For vehicles with an alarm: To prevent unin- tended triggering of the alarm, unlock the doors using the wireless remote control and
open and close a door once after the set- tings have been changed. (If a door is not
opened within 30 seconds after is
pressed, the doors will be locked again and the alarm will automatically be set.)In a case that the alarm is triggered, imme-
diately stop the alarm. ( P.77)
■Impact detection door lock release sys- tem
In the event that the vehicle is subject to a strong impact, both side doors are unlocked. Depending on the force of the
impact or the type of accident, however, the system may not operate.
■Operation signals
The emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: once; Unlocked: twice)
A buzzer sounds to indicate that the win- dows are operating.
■Security feature
If a door is not opened within approximately 30 seconds after the vehicle is unlocked,
the security feature automatically locks the vehicle again.
■Open door warning buzzer
If an attempt to lock the doors is made when a door is not fully closed, a buzzer sounds continuously for 5 seconds. Fully close the
door to stop the buzzer, and lock the vehi- cle once more.
■Setting the alarm (if equipped)
Locking the doors will set the alarm system. ( P.77)
■Conditions affecting the operation of the smart entry & start system or wire-
less remote control
 P.124
■If the smart entry & start system or the
wireless remote control does not oper- ate properly
Use the mechanical key to lock and unlock
Multi-informa-
tion dis-
play/Beep
Unlocking function
*1
*2
Exterior: Beeps 3 times
Interior: Pings once
Pushing the depression
on the front edge of the
driver’s door handle
unlocks only the driver’s
door.
Pushing the depression
on the front edge of the
passenger’s door handle
unlocks both side doors.
Exterior: Beeps twice
Interior: Pings once
Pushing the depression
on the front edge of
either door handle
unlocks both side doors.

124
-$@-$I@0.@0.&@ &&

3-2. Opening, closing and locking the doors and trunk
■Battery-saving function
The battery-saving function will be acti-
vated in order to prevent the electronic key battery and the 12-volt battery from being discharged while the vehicle is not in opera-
tion for a long time.
●In the following situations, the smart entry
& start system may take some time to unlock the doors.• The electronic key has been left within
approximately 2 m (6 ft.) of the outside of the vehicle for 10 minutes or longer.• The smart entry & start system has not
been used for 5 days or longer.
●If the smart entry & start system has not
been used for 14 days or longer, the doors cannot be unlocked at the passen-ger door. In this case, push the depres-
sion on the front edge of the driver’s door handle, or use the wireless remote con-trol or mechanical key, to unlock the
doors.
■Turning an electronic key to battery- saving mode
When battery-saving mode is set, battery depletion is minimized by stopping the elec-
tronic key from receiving radio waves.
Press twice while pressing and
holding . Confirm that the elec-
tronic key indicator flashes 4 times.
While the battery-saving mode is set, the smart entry & start system cannot be used. To cancel the function, press any of the elec-
tronic key buttons.
■Conditions affecting operation
The smart entry & star t system uses weak radio waves. In the following situations, the
communication between the electronic key and the vehicle may be affected, preventing
the smart entry & start system, wireless remote control and engine immobilizer sys-tem from operating
properly. (Ways of coping: P.389)
●When the electronic key battery is
depleted
●Near a TV tower, electric power plant,
gas station, radio station, large display, airport or other facility that generates strong radio waves or electrical noise
●When carrying a portable radio, cellular phone, cordless phone or other wireless
communication device
●When the electronic key is in contact
with, or is covered by the following metal- lic objects• Cards to which aluminum foil is attached
• Cigarette boxes that have aluminum foil inside• Metallic wallets or bags
•Coins • Hand warmers made of metal• Media such as CDs and DVDs
●When other wireless keys (that emit radio waves) are being used nearby
●When carrying the electronic key
together with the following devices that emit radio waves• Another vehicle’s electronic key or a
wireless key that emits radio waves • Personal computers or personal digital assistants (PDAs)
• Digital audio players • Portable game systems
●If window tint with a metallic content or metallic objects are attached to the rear window
●When the electronic key is placed near a battery charger or electronic devices
■Note for the entry function
●Even when the electronic key is within the effective range (detection areas), the sys-
tem may not operate properly in the fol- lowing cases:• The electronic key is too close to the win-
dow or outside door handle, near the ground, or in a high place when the doors are locked or unlocked.

141
3
-$@-$I@0.@0.&@ &&

3-3. Adjusting the seats
Before driving
will be overwritten.
■Seat positions that can be memorized
( P.138)
The adjusted positions other than the posi-
tion adjusted by lumbar support switch can be recorded.
■In order to correctly use the driving position memory function
If a seat position is already in the furthest possible position and the seat is operated in
the same direction, the recorded position may be slightly different when it is recalled.
1 Turn the engine switch switch> to IGNITION ON mode
.
2 Check that the shift position is in P.
3 Press one of the buttons for the
driving position you want to recall
until the buzzer sounds.
■To stop the position recall operation
part-way through
Perform any of the following:
●Press the “SET” button.
●Press button “1”, “2” or “3”.
●Operate any of the seat adjustment
switches (only cancels seat position recall).
●Operate the tilt and telescopic steering control switch (only cancels steering
wheel position recall).
■Operating the driving position memory after turning the engine switch off
Recorded seat positions can be activated up to 180 seconds after the driver’s door is
opened and another 60 seconds after it is closed again.
■Registering procedure
Record your driving position to button
“1”, “2” or “3” before performing the
following:
WARNING
■Seat adjustment caution
Take care during seat adjustment so that the seat does not strike the rear passen-
ger or squeeze your body against the steering wheel.
Recalling a driving position
Registering/cancel ing/recalling
a driving position to an elec-
tronic key (memor y recall func-
tion)

274
-$@-$I@0.@0.&@ &&

5-1. Remote Touch
5-1.Remote Touch
■Switches
“MAP” button (vehicles with navi-
gation system)/ “HOME” button
(vehicles without navigation sys-
tem)
“MAP” button: Press to display the current
location.
“HOME” button: Press to display the home
screen.
“MENU” button
Press to display the menu screen.
Back button
Press to display the previous screen.
Touchpad
Slide your finger on the touchpad and
move the pointer to select a function, letter
and screen button.
Press the touchpad to enter the selected
function, letter or screen button. Certain
finger movements on the touchpad can
perform functions, such as changing map
scalings and scrolling list screens.
Sub function button
When is displayed on the screen, a
function screen assigned to the screen can
be displayed.
■Using the touchpad
1 Select: Touch the touchpad to
select the desired button on the
screen.
2 Enter: The buttons on the screen
can be selected by either depress-
ing or double tapping on the
touchpad. Once a button has been
selected, the screen will change.
■Touch operation
Operations are performed by touching
the touchpad with your finger.
 Trace
Trace the pad surface while maintaining
contact with the touchpad. Moving the
cursor and the pointer.
Remote Touch
The Remote Touch can be used to
operate Center Display.
For details on the Remote Touch,
refer to the “NAVIGATION SYS-
TEM OWNER’S MANUAL”.
Remote Touch operation
A
B
C
D
E