2018 Lexus LC500 display

185
6
-$@-$I@/BWJ@0.&@ &&

6-1. Lexus parking assist monitor
Peripheral monitoring system
If you notice any of the following symptoms, refer to the likely cause and the solu-
tion, and re-check.
If the symptom is not resolved by the solution, have the vehicle inspected by any
authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer.
Things you should know
If you notice any symptoms
SymptomLikely causeSolution
The image is difficult to see
 The vehicle is in a dark area
 The temperature around
the lens is either high or low
 The outside temperature is
low
 There are water droplets
on the camera
 It is raining or humid
 Foreign matter (mud etc.) is
adhering to the camera
 Sunlight or headlights are
shining directly into the
camera
 The vehicle is under fluo-
rescent lights, sodium
lights, mercury lights etc.
Back up while visually check-
ing the vehicle’s surroundings.
(Use the monitor again once
conditions have been
improved.)
The procedure for adjusting
the picture quality of the
parking assist monitor is the
same as the procedure for
adjusting the screen display.
( P.58)
The image is blurry
Dirt or foreign matter (such
as water droplets, snow, mud
etc.) is adhering to the cam-
era.
Flush the camera with a large
quantity of water and wipe
the camera lens clean with a
soft and wet cloth.
The image is out of align-
ment
The camera or surrounding
area has received a strong
impact.
Have the vehicle inspected by
any authorized Lexus retailer
or Lexus authorized repairer,
or any reliable repairer.

186
-$@-$I@/BWJ@0.&@ &&

6-1. Lexus parking assist monitor
The guide lines are very far
out of alignment
The camera position is out of
alignment.
Have the vehicle inspected by
any authorized Lexus retailer
or Lexus authorized repairer,
or any reliable repairer.
 The vehicle is tilted (there is
a heavy load on the vehicle,
tire pressure is low due to a
tire puncture, etc.)
 The vehicle is used on an
incline.
If this happens due to these
causes, it does not indicate a
malfunction.
Back up while visually check-
ing the vehicle’s surroundings.
The estimated course lines
move even though the
steering wheel is straight
There is a malfunction in the
signals being output by the
steering sensor.
Have the vehicle inspected by
any authorized Lexus retailer
or Lexus authorized repairer,
or any reliable repairer.
Guide lines are not dis-
playedThe trunk is open.
Close the trunk.
If this does not resolve the
symptom, have the vehicle
inspected by any authorized
Lexus retailer or Lexus autho-
rized repairer, or any reliable
repairer.
The estimated course lines
are not displayed
 The steering wheel has
been moved while the 12-
volt battery was being rein-
stalled.
 12-volt battery power is
low.
 The steering sensor has
been reinstalled.
 There is a malfunction in
the signals being output by
the steering sensor.
Stop the vehicle, and turn the
steering wheel as far as it will
go to the left and right.
If this does not resolve the
symptom, have the vehicle
inspected by any authorized
Lexus retailer or Lexus autho-
rized repairer, or any reliable
repairer.
SymptomLikely causeSolution

188
-$@-$I@/BWJ@0.&@ &&

7-1. Phone operation (Hands-free system for cellular phones)
7-1.Phone ope ration (Hands -free system for cellular pho nes)
The phone top screen can be reached
by the following method:
1 Press the “MENU” button on the
Remote Touch, then select “Phone”.
Select to display the “History”
screen. ( P.192)
Select to display the “Favourites”
screen. ( P.193)
Select to display the “Contacts”
screen. ( P.193)
Select to display the “Keypad”
screen. ( P.194)
Select to select device if there are
more than 2 phones registered.
Select to display the “Message”
screen. ( P.199)
The following functions can be used on
phone operation:
 Registering/connecting Bluetooth®
device ( P.39)
 Calling on the Bluetooth® phone
( P.192)
 Receiving on the Bluetooth® phone
( P.195)
 Talking on the Bluetooth® phone
( P.196)
The following function can be used on
message function:
 Using the Bluetooth® phone mes-
sage function ( P.199)
The following settings can be made in
navigation system:
 Phone settings (P.204)
 Bluetooth® settings (P.43)
Quick reference
Phone top screen operation
Phone operation
A
B
C
D
E
F
Message function
Setting up a phone

192
-$@-$I@/BWJ@0.&@ &&

7-1. Phone operation (Hands-free system for cellular phones)
1Press the “MENU” button on the
Remote Touch.
2 Select “Phone”.
3 Select the desired method to call
from.
■Calling methods from phone top
screen
 By favourite (P.193)
 By call history (P.192)
 By contacts (P.193)
 By keypad (P.194)
 By message (P.199)
■Also the following lists are avail-
able from each function’s screen
 By POI call (P.75)
 By speech command system
( P.168)
Up to 45 of the latest call history items
(missed, incoming and outgoing) can
be selected from the “History”.
1 Press the “MENU” button on the
Remote Touch.
2 Select “Phone”.
3 Select “History” on the sub menu
and select the desired contact.
 If the contact which is not registered
on the contact list is selected, the
name is displayed as “Unknown”. In
this case, follow the guidance on the
screen to make a call properly.
4 Check that the call screen is dis-
played.
●The icons of call type are displayed.
: Missed call
: Incoming call
: Outgoing call
●When making a call to the same number continuously, only the most recent call is listed in call history.
●When a phone number registered in the contact list is received, the name is dis-
played.
●Number-withheld calls are also memo-
rized in the system.
●International phone calls may not be
Calling on the Bluetooth®
phone
After a Bluetooth® phone has been
registered, a call can be made using
the hands-free system. There are
several methods by which a call can
be made, as described below.
Calling methods on the
Bluetooth® phone
By call history

193
7
-$@-$I@/BWJ@0.&@ &&

7-1. Phone operation (Hands-free system for cellular phones)
Phone
made depending on the type of cellular phone you have.
●The list should group together consecu-tive entries with the same phone number and same call type. For example, two calls
from John’s mobile would be displayed as follows: John (2)
●By pressing the switch on the steer-
ing wheel, a call to the latest history item can be made.
Calls can be made using registered
contacts which can be selected from a
contact list. ( P.210)
1 Press the “MENU” button on the
Remote Touch.
2 Select “Phone”.
3 Select the “Favourites” on the sub
menu and select the desired con-
tact.
4 Select the desired number.
5 Check that the call screen is dis-
played.
Calls can be made by using contact
data which is transferred from a regis-
tered cellular phone. ( P.193)
Up to 5000 contacts (maximum of 4
phone numbers and 4 e-mail
addresses per contact) can be regis-
tered in the contact list.
■Calling from contacts list
1 Press the “MENU” button on the
Remote Touch.
2 Select “Phone”.
3 Select the “Contacts” on the sub
menu and select the desired con-
tact.
“E-mail Addresses”: Select to display all
registered e-mail addresses for the con- tact.
4 Select the desired number.
5 Check that the call screen is dis-
played.
■For PBAP compatible Bluetooth®
phones when “Automatic transfer”
is set to on ( P.206)
 Contacts are transferred automati-
cally.
■For PBAP compatible Bluetooth®
phones when “Automatic transfer”
is set to off ( P.206)
1 Select the desired item.
Select to always transfer all the
contacts from a connected cellular
phone automatically.
Select to transfer all the contacts
from a connected cellular phone
only once.
Select to cancel transferring.
By favour ites list
By contacts list
When the contact is empty
A
B
C

194
-$@-$I@/BWJ@0.&@ &&

7-1. Phone operation (Hands-free system for cellular phones)
2Check that a confirmation screen is
displayed when the operation is
complete.
■For PBAP incompatible but OPP
compatible Bluetooth® phones
1 Select the desired item.
Select to transfer the contacts from
the connected cellular phone.
Follow the steps in “Transfer con-
tacts from device” from step 2.
( P.207)
Select to add a new contact manu-
ally.
Follow the steps in “Registering a
new contact to the contacts list”
from step 2. (P.209)
Select to cancel transferring.
●If your cellular phone is neither PBAP nor OPP compatible, the contacts cannot be
transferred using Bluetooth®. But the contacts can be transferred from USB device. ( P.208)
●Depending on the type of Bluetooth® phone:
• It may be necessary to perform additional steps on the phone when transferring contact data.
• The registered image in the contact list may not transfer depending on the type
of Bluetooth® phone connected.
1 Press the “MENU” button on the
Remote Touch.
2 Select “Phone”.
3 Select the “Keypad” on the sub
menu and enter the phone number.
4 Select or press the switch
on the steering wheel.
5 Check that the call screen is dis-
played.
●Depending on the type of Bluetooth® phone being connected, it may be neces-
sary to perform additional steps on the phone.
■112 emergency call support
This feature is used to make a 112
emergency call. This function is not
available when the hands-free system
is not connected.
The call has to be placed from a coun-
try where 112 is available.
●The SOS function uses a different system than the ERA-GLONASS system (if equipped).
1 Press the “MENU” button on the
Remote Touch.
2 Select “Phone”.
3 Select the “Keypad” on the sub
menu and select “SOS”.
4 Select “112”.
A
B
C
By keypad
SOS

195
7
-$@-$I@/BWJ@0.&@ &&

7-1. Phone operation (Hands-free system for cellular phones)
Phone
5Check that the call screen is dis-
played.
 The current location of the vehicle is
displayed at bottom on the screen.
■Roadside assist
This feature is used to make a call to
Lexus roadside assist service.
The call has to be placed from a coun-
try where Lexus roadside assist service
is available.
To use this function, it is necessary to
register a country. ( P.212)
1 Press the “MENU” button on the
Remote Touch.
2 Select “Phone”.
3 Select the “Favourites” on the sub
menu.
4 Select “Lexus Euro assistance 24”.
5 Select .
6 Check that the call screen is dis-
played.
 The current location of the vehicle is
displayed at bottom on the screen.
1 Select “Answer” or press the
switch on the steering wheel to talk
on the phone.
Main display
Side display
To refuse to receive the call: Select “Decline”.
To adjust the volume of a received call: Turn the “PWR·VOL” knob, or use the volume
control switch on the steering wheel.
●During international phone calls, the
other party’s name or number may not be
Receiving on the Bluetooth®
phone
When a call is received, this screen
is displayed with a sound.
This screen can also be displayed
on the side display.
Incoming calls

196
-$@-$I@/BWJ@0.&@ &&

7-1. Phone operation (Hands-free system for cellular phones)
displayed correctly depending on the type of cellular phone you have.
●The ringtone that has been set in the “Sounds” screen sounds when there is an incoming call. Depending on the type of
Bluetooth® phone, both the system and
Bluetooth® phone may sound simultane- ously when there is an incoming call. ( P.204)
●The incoming call display mode can be set. ( P.205)
Main display
Select to display the keypad to send
tones. ( P.197)
Select to send tones. This button
only appears when a number that
contains a (w) is dialed in hands-
free mode. ( P.197)
Select to adjust your voice volume
that the other party hears from their
speaker. ( P.198)
Select to mute your voice to the
other party.
Select to mute navigation’s route
guidance during talking on the
phone.
Select to change handset modes
Talking on the Bluetooth®
phone
While talking on the phone, this
screen is displayed. The operations
outlined below can be performed
on this screen.
This screen can also be displayed
on the side display.
Call screen operation
A
B
C
D
E
F