2018 KIA STONIC ESP

(Continued)
Do not try remodeling the vehicle in
any way. It is illegal, and may affect
the vehicle’s performance, durability,
and safety. Warranty is also not
provided for problems caused by re‐
modeling.
Be aware of safety problems caused
by remodeling the vehicle with unau‐
thorized electrical devices (lamp,
black box, electrical equipment, diag‐
nostic device, communication device,
etc.). It might cause malfunction of
the vehicle, wiring damage, battery
discharge, connector damage, or
fire. the vehicle or cause fire.
NOTICE
nWindow tinting precaution
Window tint (especially metallic film)
might cause communication disorder
or poor radio reception, and mal‐
function of the automatic lighting
system due to excessive change of
(Continued)
(Continued)
illumination inside the vehicle. The
solution used might also flow into
electric, electronic devices causing
disorder and failure.
Inner panel fuse replacement
0:#
1. Turn the ignition switch and all oth‐er switches off.
2. Open the fuse panel cover.
3. Pull the suspected fuse straight out. Use the removal tool provided
in the main fuse box in the engine
compartment.
4. Check the removed fuse; replace it if it is blown.
Spare fuses are provided in the in‐
strument panel fuse panel (or in
the engine compartment fuse pan‐
el).
5. Push in a new fuse of the same rating, and make sure it fits tightly
in the clips.
If it fits loosely, consult a professional
workshop. Kia recommends to consult an authorized Kia dealer/service part‐
ner.

8-79
8
Maintenance

Headlamp and front fog lamp
aiming (for Europe)
Headlamp aiming
¥
5ZQF
"
¥
5ZQF
#
1. Inflate the tires to the specifiedpressure and remove any loads from the vehicle except the driver,
spare tire, and tools.
2. The vehicle should be placed on a flat floor.
3. Draw vertical lines (Vertical lines passing through respective head
lamp centers) and a horizontal line
(Horizontal line passing through center of head lamps) on the
screen.
4. With the head lamp and battery in normal condition, aim the head
lamps so the brightest portion falls
on the horizontal and vertical lines.
5. To aim the low and high beams left or right, turn the driver (1) clock‐
wise or counterclockwise. To aim
the low and high beams up or
down, turn the driver (2) clockwise
or counterclockwise.
Front fog lamp aiming
The front fog lamp can be aimed as the
same manner of the head lamps aim‐ ing.
With the front fog lamps and battery
normal condition, aim the front fog
lamps.
To aim the front fog lamp up or down, turn the driver clockwise or counter‐
clockwise.

8-121
8
Maintenance

APPEARANCE CARE
Exterior care
Exterior general caution
It is very important to follow the label
directions when using any chemical cleaner or polish. Read all warning and
caution statements that appear on the
label.
Finish maintenance
Washing
To help protect your vehicle’s finish
from rust and deterioration, wash it thoroughly and frequently at least once
a month with lukewarm or cold water.
If you use your vehicle for off-road
driving, you should wash it after each off-road trip. Pay special attention to
the removal of any accumulation of
salt, dirt, mud, and other foreign mate‐ rials. Make sure the drain holes in the
lower edges of the doors and rocker
panels are kept clear and clean.
Insects, tar, tree sap, bird droppings, in‐ dustrial pollution and similar deposits
can damage your vehicle’s finish if not
removed immediately.
Even prompt washing with plain water
may not completely remove all these
deposits. A mild soap, safe for use on
painted surfaces, may be used. After washing, rinse the vehicle thor‐
oughly with lukewarm or cold water. Do
not allow soap to dry on the finish.
CAUTION
•Do not use strong soap, chemicaldetergents or hot water, and donot wash the vehicle in direct sun‐light or when the body of the vehi‐cle is warm.
•Be careful when washing the sidewindows of your vehicle.Especially, with high-pressure wa‐ter, water may leak through thewindows and wet the interior.
•To prevent damage to the plasticparts and lamps, do not clean withchemical solvents or strong deter‐gents.
WARNING
nWet brakes
After washing the vehicle, test thebrakes while driving slowly to see if
(Continued)
(Continued)
they have been affected by water. Ifbraking performance is impaired, drythe brakes by applying them lightlywhile maintaining a slow forwardspeed.
High-pressure washing
• When using high-pressure washers, make sure to maintain sufficient dis‐
tance from the vehicle.
Insufficient clearance or excessive pressure can lead to component
damage or water penetration.
• Do not spray the camera, sensors or its surrounding area directly with a
high pressure washer. Shock applied
from high pressure water may cause the device to not operate normally.
• Do not bring the nozzle tip close to boots (rubber or plastic covers) or
connectors as they may be damaged
if they come into contact with high
pressure water.
Maintenance
8-128

Recommended SAE viscosity number
CAUTION
Always be sure to clean the area around any filler plug, drain plug, or dipstick before checking or draining any lubricant.This is especially important in dusty or sandy areas and when the vehicle is used on unpaved roads. Cleaning the plug anddipstick areas will prevent dirt and grit from entering the engine and other mechanisms that could be damaged.
Engine oil viscosity (thickness) has an effect on fuel economy and cold weather operating (engine start and engine oil flowabil‐
ity). Lower viscosity engine oils can provide better fuel economy and cold weather performance, however, higher viscosity en‐ gine oils are required for satisfactory lubrication in hot weather. Using oils of any viscosity other than those recommended
could result in engine damage.
When choosing an oil, consider the range of temperature your vehicle will be operated in before the next oil change. Proceed to select the recommended oil viscosity from the chart.

9-15
9
Specifications & Consumer information