2018 KIA STONIC Start

Instrument panel (Driver’s side fuse panel)
SymbolFuse rat‐ingCircuit Protected
20A Tail Gate Unlock Relay, Dead Lock Relay, Door Lock/Unlock Relay
20A Power Outlet
25A Driver Safety Power Window Module
STOP
LAMP15A Stop Signal Electronic Module
15A BCM (Body Control Module), SLM Unit
20A Cigarette Lighter
10A Driver Power Outside Mirror, Passenger Power Outside Mirror, Air Conditioner Control Module, ECM
(Engine Control Module)/PCM (Power train Control Module)
10A Outside Mirror Folding
RH25A Power Window Main Switch, Passenger Power Window Switch(LHD)
20A Front Seat Warmer Control Module
10A DRL (Daytime Running Light) Relay
7.5A With Immobilizer & Smart Key : ECM (Engine Control Module)/PCM (Power train Control Module), En‐ gine Room Junction Block(Start Relay)
Without Immobilizer & Smart Key : Burglar Alarm Relay
7.5A Head Lamp RH, License Lamp RH(Sedan), Rear Combination Lamp (IN) RH(Wagon), ILL (+)
Maintenance

8-84

SymbolFuse rat‐ingCircuit Protected
10ABCM (Body Control Module), Crash Pad Switch, FCA Unit, Lane Departure Warning System, BLIND-
SPOT DETECTION WARNING Radar LH/RH
15AEngine Room Junction Block(Back-Up Lamp Switch), Sport Mode Switch, Speed Sensor, Stop Lamp
Switch, Speed Sensor (In/Out), Transaxle Range Switch
LH25A Power Window Main Switch, Passenger Power Window Switch(RHD)
SPARE25A Spare
10A Rear Fog Lamp Relay
15A Clock Spring
LH7.5A Head Lamp LH, License Lamp LH(Sedan), Rear Combination Lamp (IN) LH(Wagon)
7.5A Front Console Switch, Front Seat Warmer Control Module, Audio, Audio / Video & Navigation Head
Unit, Head Lamp Leveling Device Actuator LH/RH, Air Conditioner Control Module, Electro Chromic
Mirror, Crash Pad Switch, DC-DC Converter, Clock Spring, A/T Shift Lever Indicator
7.5A
Engine Room Junction Block(Multipurpose Check Connector), ABS/ESC (Electronic Stability Control)
Control Module
10A Smart Key Control Module, Stop Lamp Switch
SPARE15A Spare
15A Front Fog Lamp Relay
7.5AEngine Room Junction Block(Air Conditioner Blower Relay), GSL Junction Block(PTC Heater Relay),
DSL Junction Block(Start Relay, Air Conditioner Blower Relay), Air Conditioner Control Module
MODULE510AEngine Room Junction Block(Head Lamp High Relay, Head Lamp Relay), Front Seat Warmer Control
Module, BCM (Body Control Module)


8-85
8
Maintenance

SymbolFuse ratingCircuit Protected
POWER
OUTLET40A Instrument Panel Junction Block (Power Outlet Relay)

Relay(Kappa 1.0L T-GDI Engine (Gaso‐
line))
SymbolRelay NameType
Start Relay MICRO
A/C Blower Relay MICRO
FUEL
PUMPFuel Pump Relay MICRO
Wiper HI RelayMICRO
LOWiper LO Relay MICRO
Head Lamp High Relay MICRO
Head Lamp RelayMICRO
Air Conditioner Clutch Type ECV Relay MICRO
Horn RelayMICRO
Burglar Alarm Horn Relay MICRO
MAINMain RelayMINI
Cooling Fan Relay MINI

8-93
8
Maintenance

Relay(Kappa 1.2L MPI Engine (Gaso‐
line))
SymbolRelay NameType
Start RelayMICRO
A/C Blower Relay MICRO
FUEL
PUMPFuel Pump Relay MICRO
Cooling Fan1 Relay MICRO
Wiper HI RelayMICRO
LOWiper LO Relay MICRO
Head Lamp High Relay MICRO
Head Lamp RelayMICRO
2Cooling Fan2 Relay MICRO
Horn RelayMICRO
Burglar Alarm Horn Relay MICRO
MAINMain RelayMINI
Air Conditioner Clutch Type ECV Relay MICRO
Maintenance
8-96

SymbolFuse ratingCircuit Protected
40A Ignition Switch, PDM Relay Box (IG1 Relay, ACC Relay)
POWER
OUTLET40A Instrument Panel Junction Block (Power Outlet Relay)
Relay(Kappa 1.4L MPI Engine (Gaso‐
line))
SymbolRelay NameType
Start Relay MICRO
A/C Blower Relay MICRO
FUEL
PUMPFuel Pump Relay MICRO
Cooling Fan1 Relay MICRO
Wiper HI RelayMICRO
LOWiper LO Relay MICRO
Head Lamp High Relay MICRO
Head Lamp RelayMICRO
2Cooling Fan2 Relay MICRO
Horn RelayMICRO
Burglar Alarm Horn Relay MICRO
MAINMain RelayMINI

8-99
8
Maintenance

SymbolFuse ratingCircuit Protected
AMS10A Battery Sensor
40A Instrument Panel Junction Block (Tail Lamp Relay)
40A Ignition Switch, PDM Relay Box (IG1 Relay, ACC Relay)
POWER
OUTLET40A Instrument Panel Junction Block (Power Outlet Relay)
Relay(U-II 1.4L/1.6L Engine (Diesel))
SymbolRelay NameType
Start Relay MICRO
A/C Blower Relay MICRO
FUEL
PUMPFuel Pump Relay MICRO
Cooling Fan1 Relay MICRO
Wiper HI RelayMICRO
LOWiper LO Relay MICRO
Head Lamp High Relay MICRO
Head Lamp RelayMICRO
2Cooling Fan2 Relay MICRO
Horn RelayMICRO
Maintenance
8-102

Moisture breeds corrosion
Moisture creates the conditions in
which corrosion is most likely to occur. For example, corrosion is accelerated
by high humidity, particularly when
temperatures are just above freezing. In such conditions, the corrosive mate‐
rial is kept in contact with the vehicle’s
surface by moisture that evaporate slowly.
Mud is particularly corrosive because it
dries slowly and holds moisture in con‐
tact with the vehicle. Although the mud appears to be dry, it can still retain
moisture and promote corrosion.
High temperatures can also accelerate
corrosion of parts that are not properly ventilated so the moisture can be dis‐
persed.
For all these reasons, it is particularly
important to keep your vehicle clean and free of mud or accumulations of
other materials. This applies not only to
the visible surfaces but particularly to
the underside of the vehicle.
To help prevent corrosion
You can help prevent corrosion from getting started by observing the fol‐
lowing:
Keep your vehicle clean
The best way to prevent corrosion is to
keep your vehicle clean and free of cor‐
rosive materials. Attention to the un‐ derside of the vehicle is particularly im‐
portant. • If you live in a high-corrosion area — where road salts are used, near the
ocean, areas with industrial pollution,
acid rain, etc.—, you should take ex‐ tra care to prevent corrosion. In win‐
ter, hose off the underside of your
vehicle at least once a month and be
sure to clean the underside thor‐
oughly when winter is over.
• When cleaning underneath the vehi‐ cle, give particular attention to the
components under the fenders and
other areas that are hidden from
view. Do a thorough job; just damp‐ ening the accumulated mud rather
than washing it away will accelerate
corrosion rather than prevent it. Wa‐
ter under high pressure and steam
are particularly effective in removing accumulated mud and corrosive ma‐
terials. • When cleaning lower door panels,
rocker panels and frame members,
be sure that drain holes are kept
open so that moisture can escape and not be trapped inside to acceler‐
ate corrosion.
Keep your garage dry
Don't park your vehicle in a damp, poor‐
ly ventilated garage. This creates a fa‐ vorable environment for corrosion. This
is particularly true if you wash your ve‐
hicle in the garage or drive it into the garage when it is still wet or covered
with snow, ice or mud. Even a heated
garage can contribute to corrosion un‐ less it is well ventilated so moisture is
dispersed.
Keep paint and trim in good
condition
Scratches or chips in the finish should
be covered with "touch-up" paint as soon as possible to reduce the possibili‐
ty of corrosion. If bare metal is showing
through, the attention of a qualified body and paint shop is recommended.
Bird droppings : Bird droppings are
highly corrosive and may damage pain‐
ted surfaces in just a few hours. Al‐ ways remove bird droppings as soon as
possible.

8-131
8
Maintenance

• If you use unauthorized electronicdevices, it may cause the vehicle to
operate abnormally, wire damage, battery discharge and fire. For your
safety, do not use unauthorized elec‐
tronic devices.
Engine exhaust gas precautions
(carbon monoxide)
• Carbon monoxide can be present with other exhaust fumes. Therefore, if
you smell exhaust fumes of any kind inside your vehicle, have it inspected
and repaired immediately. If you ever
suspect exhaust fumes are coming
into your vehicle, drive it only with all
the windows fully open. Have your vehicle checked and repaired immedi‐
ately.
WARNING
nExhaust
Engine exhaust gases contain carbonmonoxide (CO). Though colorless andodorless, it is dangerous and couldbe lethal if inhaled. Follow the in‐structions on this page to avoid COpoisoning.
• Do not operate the engine in confined or closed areas (such as garages) any
more than what is necessary to move the vehicle in or out of the area.
• When the vehicle is stopped in an open area for more than a short time
with the engine running, adjust the
ventilation system (as needed) to
draw outside air into the vehicle.
• Never sit in a parked or stopped vehi‐ cle for any extended time with the
engine running.
• When the engine stalls or fails to start, excessive attempts to restart
the engine may cause damage to the
emission control system.
Operating precautions for catalytic
converters (if equipped)
WARNING
nFire
(Continued)
(Continued)
•A hot exhaust system can igniteflammable items under your vehi‐cle. Do not park the vehicle over ornear flammable objects, such asgrass, vegetation, paper, leaves,etc.
•The exhaust system and catalyticsystem are very hot while the en‐gine is running or immediately af‐ter the engine is turned off. Keepaway from the exhaust systemand catalytic, you may get burned.Also, do not remove the heat sinkaround the exhaust system, donot seal the bottom of the vehicleor do not coat the vehicle for cor‐rosion control. It may present afire risk under certain conditions.
Your vehicle is equipped with a catalytic
converter emission control device.
Therefore, the following precautions must be observed: • Make sure to refuel your vehicle ac‐ cording to the L