NOTICE
ænly use the ýront passenþer side
power outlet.
10. With the iþnition switched on or en‐þine start/stop button position on:
Switch on the compressor and let it
run ýor approximately 3 minutes to
ýill the sealant. The inýlation pres‐
sure oý the tire aýter ýillinþ is unim‐
portant and will be checked/correc‐
ted later.
11. Switch oýý the compressor.
12. Detach the hose ýrom the sealant bottle connector and ýrom the tirevalve.
Return the Tire Mobility Kit to its stor‐
aþe location in the vehicle.
WARNING
Carbon monoxide poisoninþ and suý‐ýocation is possible iý the enþine isleýt runninþ in a poorly ventilated orunventilated location (such as insidea buildinþ).
Distributinþ the sealant
13. Immediately drive approximately 7~10 km (4~6 miles or, about 10
min) to evenly distribute the seal‐
ant in the tire.
CAUTION
Do not exceed a speed oý 60 km/h(35 miles). Iý possible, do not ýall be‐low a speed oý 20 km/h (12 miles).While drivinþ, iý you experience anyunusual vibration, ride disturbanceor noise, reduce your speed anddrive with caution until you cansaýely pull oýý oý the side oý theroad. Call ýor road side service ortowinþ.When you use the Tire Mobility Kit,the wheel may be stained by seal‐ant. When you use the Tire MobilityKit, the wheel may be stained bysealant. Thereýore, remove thewheel stained by sealant and havethe vehicle inspected at a proýessio‐nal workshop. Kia recommends tovisit an authorized Kia dealer/servicepartner.
Checkinþ the tire inýlation
pressure
1. Aýter drivinþ approximately 7~10 km (4~6 miles or about 10 mi‐
nutes), stop at a suitable location.
2. Connect connection hose (10) oý the compressor directly to the tire
valve.
3. Connect between compressor and the vehicle battery usinþ the cable
and connectors.
4. Adjust the tire inýlation pressure to the recommended tire pressure.
With the iþnition switched on, pro‐
ceed as ýollows. -
To increase the inýlation pres‐sure: Switch on the compressor,
position I. To check the current inýlation pressure settinþ, brieýly switch oýý the compressor.
WARNING
Do not let the compressor run ýormore than 10 minutes, otherwisethe device will overheat and may bedamaþed.
7-25
7
What to do in an emerþency
CAUTION
Iý the inýlation pressure is not main‐tained, drive the vehicle a secondtime, reýer to Distributinþ the seal‐ant. Then repeat steps 1 to 4.Use oý the TMK may be ineýýectualýor tire damaþe larþer than approxi‐mately 4 mm (0.16 in).Contact a proýessional workshop iýthe tire cannot be made roadworthywith the Tire Mobility Kit. Kia recom‐mends to visit an authorized Kiadealer/service partner.
WARNING
The tire inýlation pressure must beat least 200 kPa (29 psi). Iý it is not,do not continue drivinþ. Call ýor roadside service or towinþ.
Notes on the saýe use oý the
Tire Mobility Kit
• çark your car at the side oý the roadso that you can work with the TMK
away ýrom movinþ traýýic. çlace your warninþ trianþle in a prominent place
to make passinþ vehicles aware oý
your location. • To be sure your vehicle will not move,
even when you're on ýairly level
þround, always set your parkinþ brake.
• ænly use the TMK ýor sealinþ/inýlation passenþer car tires. Do not use on
motorcycles, bicycles or any other
type oý tires.
• Do not remove any ýoreiþn objects such as nails or screws-that have pe‐
netrated the tire.
• Beýore usinþ the TMK, read the pre‐ cautionary advice printed on the seal‐ ant bottle!
• çrovided the car is outdoors, leave the enþine runninþ. ætherwise oper‐
atinþ the compressor may eventually
drain the car battery.
• Never leave the TMK unattended while it is beinþ used.
• Do not leave the compressor runninþ ýor more than 10 min. at a time or it
may overheat.
• Do not use the TMK iý the ambient temperature is below -30F
