2018 JEEP RENEGADE display

Symbol What it means
ENGINE OIL DETERIORATED
(where provided)
Diesel versions: the symbol is displayed on some versions, along with a dedicated message displaying.
The symbol is displayed for 3 minute cycles and intervals of 5 seconds until oil is changed. The symbol
is displayed until the problem is solved.
Petrol versions: the symbol switches on and then is not displayed when the display cycle is completed.
IMPORTANT After the first indication, each time the engine is started the symbol will continue to
switch on as described above until the oil is changed. On certain versions a dedicated message is
displayed.
If the symbol flashes, this does not mean that there is a fault on the vehicle, rather it simply reports
that it is now necessary to change the oil as a result of regular use of the vehicle. The deterioration of
engine oil is accelerated by using the car for short drives, preventing the engine from reaching
operating temperature.
Contact a Jeep Dealership as soon as possible.
IMPORTANT
30)If thewarning light comes on, the exhausted engine oil should be changed as soon as possible, never drive more than 500 km
from the first switching-on of this warning light. Failure to observe the above may result in severe damage to the engine and invalidate the
warranty. Remember that when this warning light comes on, it does not mean that the level of engine oil is low, so if it flashes you do not
need to top up the engine oil.
31)If the
warning light flashes when driving, contact a Jeep Dealership.
93
30)
31)

Symbol What it means
EXTERIOR LIGHTS FAILURE
The symbol turns on to indicate a failure of the following lights: daytime running lights (DRLs); parking
lights; trailer direction indicators (if present); trailer lights (if present); side lights; direction indicators;
rear fog light; reversing light; brake lights; number plate lights.
The failure may be caused by a blown bulb, a blown protection fuse or an interruption of the electrical
connection.
ADAPTIVE CRUISE CONTROL (ACC) FAILURE
The symbol turns on (together with a message on the display) to indicate an Adaptive Cruise Control
(ACC) system failure. In this case, contact a Jeep Dealership as soon as possible.
94
KNOWING THE INSTRUMENT PANEL

Symbol What it means
DPF CLEANING (particulate trap) in progress (diesel versions with DPF only)
The symbol switches on constantly to indicate that the DPF system needs to eliminate the trapped
pollutants (particulate) through the regeneration process.
The symbol does not switch on during every DPF regeneration, but only when driving conditions require
that the driver is notified. To turn off the symbol, keep the vehicle in motion until the regeneration
process is over. On average, the process lasts 15 minutes. Optimal conditions for completing the
process are achieved by travelling at 60 km/h with engine speed above 2000 rpm.
When this symbol switches on, it does not indicate a vehicle failure and thus it should not be taken to a
workshop. On some versions, together with the symbol switching on, the display shows a dedicated
message.
IMPORTANT
32)Vehicle travel speed should always be adapted to the traffic and weather conditions, and must always comply with traffic regulations.
The engine can be stopped even if the DPF warning light is on: however, repeated interruptions of the regeneration process could cause
premature deterioration of the engine oil. For this reason it is always advisable to wait for the symbol to go off before turning off the engine,
following the instructions above. Do not complete the DPF regeneration process when the vehicle is stopped.
95
32)

Green symbols
Symbol What it means
RUNNING ON PETROL
The symbol turns on when running on petrol.
White symbols
Symbol What it means
SPEED LIMIT EXCEEDED
The symbol switches on when the limit is set through the display Menu. In markets where provided, the speed
limit is fixed and cannot be set from the Menu.
HILL DESCENT CONTROL (where provided)
System activation: symbol switched on continuously along with the display of a dedicated message.
System failed activation: LED on the button in the central tunnel switched on (see “Active Safety Systems”
paragraph in the “Safety” chapter).
ELECTRONIC CRUISE CONTROL
The symbol switches on if the electronic Cruise Control is activated.
SPEED LIMITER
The symbol switches on if the Speed Limiter device is activated.
96
KNOWING THE INSTRUMENT PANEL

Messages on the display
Message on the display
SERV 4WDFOUR WHEEL DRIVE FAILURE
This indicator switches on to report a four wheel drive system failure. Contact a Jeep
Dealership as soon as possible.
BLIND-SPOT MONITORINGBLIND-SPOT MONITORING SYSTEM
Sensor locking: in case of failure of the Blind-Spot Monitoring system, a message will
appear on the display. In this case, the LEDs on the door mirrors are switched on
continuously. Free the bumper of any obstacles or clean it.
System not available: in case the Blind-Spot Monitoring system is not available, a
message will appear on the display. In this case, the LEDs on the door mirrors are
switched on continuously. The failed operation of the system might be due to the
insufficient voltage from the battery or other failures on the electrical system. Contact a
Jeep Dealership as soon as possible to have the electrical system checked.
Blind-Spot Monitoring system failure: in case of a failure of the Blind-Spot Monitoring
system, a message will appear on the display. In this case, the LEDs on the door mirrors
are switched off. An acoustic signal is also emitted. Contact a Jeep Dealership as soon
as possible.
97

Message on the display
PARKSENSEPARKSENSE SYSTEM (where provided)
Sensor locking: the message is displayed in the case of a failure of the ParkSense system
sensors. Free the bumpers of any obstacles, cleaning them.
System not available: a dedicated message is displayed if the ParkSense system is not
available. The failed operation of the system might be due to the insufficient voltage
from the battery or other failures on the electrical system. Contact a Jeep Dealership as
soon as possible to have the electrical system checked.
ACTIVE PARKSENSEACTIVE PARKSENSE (where provided)
Sensor locking: the message is displayed in the case of a failure of the Active ParkSense
system sensors. Free the bumpers of any obstacles, cleaning them.
System not available: a dedicated message is displayed if the Active ParkSense system is
not available. The failed operation of the system might be due to the insufficient voltage
from the battery or other failures on the electrical system. Contact a Jeep Dealership as
soon as possible to have the electrical system checked.
SIDE DISTANCE WARNINGSIDE DISTANCE WARNING (where provided)
Sensor locking: the message is displayed in the case of a failure of the Side Distance
Warning system sensors. Free the bumpers of any obstacles, cleaning them.
System not available: a dedicated message is displayed if the Side Distance Warning
system is not available. The failed operation of the system might be due to the
insufficient voltage from the battery or other failures on the electrical system. Contact a
Jeep Dealership as soon as possible to have the electrical system checked.
98
KNOWING THE INSTRUMENT PANEL

Message on the display
LANESENSELANESENSE (where provided)
Camera obstructed: a dedicated message is shown on the display in the case of dirt on
the windscreen, which may adversely affect correct operation of the camera. Clean the
windscreen using a soft clean cloth, taking care not to scratch it. Should the failure
persist, contact a Jeep Dealership as soon as possible.
System not available: a dedicated message is displayed if the LaneSense system is not
available.
DYNAMIC STEERING TORQUEDST SYSTEM (Dynamic Steering Torque)
A dedicated message is displayed in the event of DST system failure. Contact a Jeep
Dealership as soon as possible.
"SERVICE" MESSAGE (SCHEDULED
SERVICING)SCHEDULED SERVICING (SERVICE)
When the following scheduled servicing is approaching ("coupon"), the word "Service"
will be displayed, followed by the number of kilometres/miles or days (where provided)
left, when the ignition device is turned to MAR.
Contact a Jeep Dealership. The operations of the "Scheduled Servicing Plan" will be
performed and the message will be reset.
99

ERM (Electronic Rollover
Mitigation) SYSTEM
The system monitors the tendency of the
wheels to rise from the ground if the
driver performs extreme manoeuvres like
quick steering to avoid an obstacle,
especially in poor road conditions.
If these conditions occur, the system
intervenes on the brakes and engine
power to reduce the possibility that the
wheels are raised from the ground. It is
not possible to avoid tendency to roll over
if the phenomenon is due to reasons
such as driving on high side gradients,
collision with objects or other vehicles.
59)
TSC (Trailer Sway Control)
SYSTEM
The system employs a series of sensors
located on the vehicle to identify
excessive swerving of the trailer and take
the necessary precautions to eliminate it.
System intervention
When the system is active, the
warning light flashes on the
instrument panel, the engine power is
reduced and braking can be felt on the
individual wheels, following the attempt
to eliminate the swerving of the trailer.
The system is active only with ESC
engaged.When the ESC system is deactivated (by
pressing the button on the central
tunnel), the TSC system is deactivated as
well.
60) 61)
HDC (Hill Descent Control)
SYSTEM
(where provided)
62) 63)
On cars equipped in this way, this
function is an integral part of the ESC
system and is aimed at keeping the car
at a constant speed during a descent,
operating autonomously and in different
ways on the brakes.
In this way the vehicle stability and
completely safe driving are guaranteed,
above all in poor grip conditions and
steep descents.
Enabling the system
To enable the system, press the button
fig. 70.The system is enabled if the following
conditions are met:
theSelec-Terrain™device is in 4WD
LOW mode;
the vehicle speed is below 12 km/h;the electric parking brake (EPB) is
deactivated;
the driver side door is closed.
The system activation is reported by the
continuous switching-on of the icon
on
the display along with a dedicated
message.
Activation of the system
Once enabled, the HDC system will
activate automatically if the vehicle is
driven downhill on a steep slope, higher
than 8%.
70J0A0907C
103