GEAR SHIFT INDICATOR(where provided)
The Gear Shift Indicator (GSI) system
advises the driver to change gear through
a special indication on the display.
Through the GSI, the driver is informed
that the gear change will allow a
reduction in fuel consumption.
SHIFT UP (
SHIFT) icon on the
display: suggests switching to a higher
gear.
SHIFT DOWN (
SHIFT) icon on the
display: suggests switching to a lower
gear.
The indication in the display remains
until a gear is shifted or the driving
conditions go back to a situation where
gearshifting is not required to improve
consumption.
CONTROL BUTTONS
These are located on the left side of the
steering wheel fig. 69.They allow the driver to select the items
in the Main menu of the display (see
paragraph "Main menu").
/: press and release the
buttons to scroll the main menu and the
submenus upwards or downwards.
/: press and release the buttons
to access the info screens or the
submenus of an item of the main menu.
Button
allows you to exit the Main
menu.
OK: press this button to access/select
the info screens or the submenus of an
item of the main menu. Hold the button
pressed for one second to reset the
displayed/selected functions.
MAIN MENU
Menu items
The Menu includes the following items:
SPEEDOMETERVEHICLE INFODRIVER ASSISTFUEL ECOTRIPSTOP/STARTAUDIOALERTSDISPLAY SET-UPVEHICLE SETUP
The Menu item display mode (capital or
lower-case letters) changes according to
the type of display.
Some options have a submenu.
NOTE With theUconnect™system, some
Menu items are shown and managed on
the display of the latter and not on the
instrument panel display (see the
paragraphs on theUconnect™).
Vehicle setup (Change vehicle settings)
This function allows you to change the
settings for:
“Vehicle off” (where provided);“Display”;"Units";“Clock & Date”;"Safety";“Safety & Assistance”;
69J0A0189C
68
KNOWING THE INSTRUMENT PANEL
On some versions, with mode engaged,
the display shows "4WD LOW". The LED
on theSelec-Terrain™device may flash
until the end of the engagement.
4WD LOW mode release
The release can occur at any speed
ranging from 0 to 120 km/h.
On some versions, "4WD LOW" on the
display switches off at the end of the
release procedure.
In this case, the LED on the 4WD LOW
button is off.
IMPORTANT
51)The correct operation of the 4WD
function depends on the tyres: all of them
must have the same size, the same type
and the same circumference. Using tyres
with different sizes has negative effects on
the gear change and damages the
components of the transmission.
52)Do not drive at speeds exceeding those
that the road conditions allow for.
SELEC-TERRAIN
DRIVING MODE SELECTION
Turn knob A fig. 111 to select the
desired mode.
IMPORTANT Changing mode is not
possible when the vehicle speed is
over 120 km/h.
AUTO (Automatic): the 4WD mode with
continuous and automatic operation can
be used while driving on road and
off-road. This mode reduces fuel
consumption, because the propeller shaft
can be disconnected, whenever required.
SNOW: this mode can achieve more
stability on slippery or snow-covered
grounds. To be used for driving on-road
and off-road in the case of grounds with
poor grip, such as roads covered by snow.
SAND: off-road driving mode to be
used on surfaces with poor grip, such as
sandy surfaces. The transmission is set
to offer a maximum traction.
MUD: off-road driving mode for
surfaces with poor grip, such as
mud-covered grounds or wet grass.
ROCK(where provided, for Trailhawk
versions only): this mode is only available
if the 4WD LOW mode is activated. The
device sets the car to maximise traction
and give the highest steering capacity on
off-road surfaces featuring a high grip.
This mode guarantees the best "off-road"
performance. This mode must be used to
pass over obstacles at slow speed, such
as large rocks, deep cracks, etc.
When the engine is started, the AUTO
mode is automatically selected (LED on
close to the AUTO wording).
Turning the knob A fig. 111 the LED
close to the AUTO wording comes on
111J0A0920C
158
STARTING AND DRIVING
