2018 JEEP RENEGADE sensor

WARNING
18)As the driver's door mirror is curved, it
may slightly alter the perception of
distance.
EXTERIOR LIGHTS
LIGHT SWITCH
Light switch A fig. 31, located on the left
side of the instrument panel (left hand
drive versions) or on the right side (right
hand drive versions), controls the
headlamp operations, parking lights,
daytime lights, low beams, fog lights,
rear fog lights, and regulates the
instrument panel lighting and the
symbols on the control buttons.
Outside lighting can happen only when
the starter is in position MAR.
The instrument panel and the variouscontrols on the dashboard will be lit up
when the exterior lights are switched on.
AUTO FUNCTION(Dusk sensor)
(where provided)
This is an infrared LED sensor that works
in conjunction with the rain sensor and is
located on the windscreen. It is able to
detect variations in outside lighting
based on the light sensitivity and adjusts
the display Menu or theUconnect™
system.
The higher the sensitivity, the lower the
amount of external light needed to switch
the lights on.
Function activation: turn the light switch
to AUTO.
Function deactivation: turn the light
switch to a position other than AUTO.
IMPORTANT This function can only be
activated with the ignition device at
MAR.
DIPPED BEAM HEADLIGHTS
With the ignition device on MAR, turn
the switch to. If the dipped beam
headlights are activated, the daytime
lights are switched off and the dipped
beam headlights, side lights and number
plate lights are switched on. The
30J0A0209C
31J0A0888C
31

warning light switches on in the
instrument panel.
DAYTIME RUNNING LIGHTS
(DRL)
"Daytime Running Lights"
(where provided)
19) 20)
With the ignition device turned to MAR
and the light switch turned to positionO
the daytime running/side lights are
automatically activated; the other lights
and interior lighting remain off.
The daytime running lights are
temporarily deactivated when the
direction indicators are activated. When
the direction indicators are deactivated,
the daylight running lights are
reactivated.
FRONT FOG LIGHTS(where provided)
With the ignition device in MAR, with the
side lights and dipped beam headlights
on, press switch
to turn on the fog
lights.
To switch off the fog lights press the
switch again or turn it to positionO.
“Cornering Lights” function
The function activates with the main
beam headlights switched on with a
speed lower than 40 km/h - For widewheel rotation angles or at the switching
on the direction indicator, a light will
turn on (built in the front fog light)
referring to the turning side which will
extend the night visibility angle.
REAR FOG LIGHT
With ignition device in MAR, press thebutton to switch the light on/off.
The rear fog light switches on only when
the dipped beam headlights or fog lights
are switched on. The light switches off by
pressing the
button or by switching off
the main beam headlights or the fog
lights.
PARKING LIGHTS
These can be turned on by turning the
light switch ring to theposition. Thewarning light on the instrument
panel turns on.
IMPORTANT NOTE Do not select this
light switch position when the car is
moving, but only to indicate that the car
is parked when prescribed by the
regulations in force in the country where
you are driving (Highway Code).
To turn the lights off, turn the light
switch ring to theOposition
HEADLIGHTS OFF TIMER
Function activation
It is possible to enable switching on the
lights for the preset time by turning the
ignition device to STOP, with the light
switch ring nut in position
and then
turning the ring nut to positionO.
IMPORTANT To activate this function
the headlights must be deactivated
within 2 minutes after the ignition
device has been taken to STOP.
Automatic function activation
(where provided)
If the car is equipped with a dusk sensor,
it is possible to enable the function
automatically: with the ignition device in
MAR, turn the light switch ring nut to
AUTO, if the sensor reports low light
levels, it will enable the dipped beam
headlights.
The headlights off delay is enabled
automatically when the ignition device is
turned to STOP with the headlights on
for the time selected in the Menu.
Function deactivation
This function is disabled by waiting for
the time set from the Menu, or by turning
the ignition device to the MAR position.
32
GETTING TO KNOW YOUR CAR

Move the stalk upwards (unstable
position) to activate the MIST
function: operation is limited to the
time for which the stalk is held in this
position. When released, the stalk will
return to its default position and the
windscreen wiper will be automatically
stopped.
IMPORTANT This function does not
activate the windscreen washer;
windscreen washer fluid will not
therefore be sprayed onto the
windscreen. To spray windscreen washer
fluid onto the windscreen, the washing
function must be used. With the ring A in
position
, the windscreen wiper is not
activated. In position, the pause time
between the strokes of the windscreenwiper is 10 seconds, independently of
the vehicle speed. In position
, the
pause time between two strokes is set
according to the vehicle speed: when the
speed increases, the time between two
strokes decreases. In positionLOorHI,
the windscreen wiper moves
continuously, i.e. without a pause
between two strokes.
“Smart washing” function
Pull the stalk towards the steering wheel
(unstable position) to operate the
windscreen washer.
When the stalk is held pulled for longer
than half a second, the windscreen wiper
moves with active control. Releasing the
stalk will activate three strokes.
With the ring A in theLOorHIposition,
the smart washing function is not
performed.
The windscreen wiper stops working
three strokes after the stalk is released.
IMPORTANT If the stalk is activated for
less than half a second, only the
windscreen washer jet is activated. Do
not prolong the activation of the "Smart
Washing" function for more than
30 seconds. Do not activate the
windscreen washer control when the
reservoir is empty.RAIN SENSOR
(where provided)
9) 10)
It is located behind the interior rear view
mirror, in contact with the windscreen,
and can detect the presence of rain and,
consequently, manage the automatic
windscreen wiping mode depending on
the amount of water on the screen (see
the “Automatic Wiping” paragraph).
The sensor will be activated when the
ignition device is turned to MAR, and will
be disabled with the ignition device in
the STOP position.
Automatic Wiping
Activation
You can choose automatic wiping by
selecting the rain sensor from the display
Menu or on theUconnect™system and
turning ring A to the
orposition.
Activation of the automatic wiping
function is signalled by a flick. The same
stroke will be visible every time the
sensor sensitivity is increased, by rotating
the ring nut from position
to position.
Inhibition
If the ignition device is turned to STOP,
leaving the ring nut A in position
or,
when the engine is next started (ignition
35J0A0774C
36
GETTING TO KNOW YOUR CAR

device at MAR), no wiping cycle occurs
for system protection reasons.
It is possible to reactivate the automatic
wiping mode in three ways:
by rotating ring A to theposition
and back to theorpositionby moving the stalk upwards to
position MIST
upon exceeding the 5 km/h speed with
the rain sensor
Deactivation
Use the display Menu or the Uconnect
(TM)system, or turn ring A to any
non-intermittent position (or).
REAR WINDOW WIPER /
WASHER
Activation
Ring B can be set to the following
positions:
rearscreen wiper offintermittent wipe
continuous operation, without
pausing between two strokes.
By operating ring nut B, the rear window
wiper can function in the following
modes:
continuous: when the ring is turned to
theposition;intermittent: when the ring nut is in
positionand the rear window wiper is
stopped;
synchronous: when the ring nut is in
positionand the rear window wiper is
moving or set to AUTO. In this mode, the
rear window wiper makes one stroke for
each two strokes of the windscreen
wiper;
single stroke: when the ring is in theposition, the windscreen wiper is
active and reverse gear is engaged.
Push the stalk towards the dashboard
(rocking position) to activate the rear
window washer jet. Keep pushing the
lever to automatically activate both the
rear window washer jet and the rear
window wiper with a single movement.
Deactivation
The function stops when the stalk is
released.
WARNING
21)Make sure the device is switched off
whenever the windscreen must be
cleaned.
IMPORTANT
7)Never use the windscreen wipers to
remove layers of snow or ice from the
windscreen. In such conditions, the
windscreen wiper may be subjected to
excessive stress and the motor cut-out
switch, which prevents operation for a few
seconds, may intervene. If operation is not
subsequently restored, even after
restarting the engine, contact a Jeep
Dealership.
8)Do not operate the windscreen wiper
with the blades lifted from the windscreen.
9)Do not activate the rain sensor when
washing the car in an automatic car wash.
10)Make sure the device is switched off if
there is ice on the windscreen.
37

CONTROL PANEL AND ON-BOARD INSTRUMENTS
VERSIONS WITH MULTIFUNCTION DISPLAY
A. Engine speed indicator / B. Digital engine coolant thermometer with maximum temperature warning light / C. Multifunction
display / D. Digital fuel level indicator with low fuel warning light (the triangle on the right side of thesymbol indicates the side
of the vehicle where the fuel filler is) / E. Vehicle speed indicator (there is light sensor inside the speed indicator)
Warning light present on Diesel versions only. Diesel versions also have theicons on the display and the full scale on the
engine speed indicator is 6000 rpm.
IMPORTANT The illumination of the instrument panel graphics may vary according to version.
63J0A0005C
63

64J0A0239C
64
KNOWING THE INSTRUMENT PANEL
VERSIONS WITH MULTIFUNCTION DISPLAY (right hand drive versions)
A. Engine speed indicator / B. Digital engine coolant thermometer with maximum temperature warning light / C. Multifunction
display / D. Digital fuel level indicator with low fuel warning light (the triangle on the right side of thesymbol indicates the side
of the vehicle where the fuel filler is) / E. Vehicle speed indicator (there is light sensor inside the speed indicator)
Warning light present on Diesel versions only. Diesel versions also have theicons on the display and the full scale on the
engine speed indicator is 6000 rpm.
IMPORTANT The illumination of the instrument panel graphics may vary according to version.

VERSIONS WITH RECONFIGURABLE MULTIFUNCTION DISPLAY
A. Engine speed indicator / B. Digital engine coolant thermometer / C. Reconfigurable multifunction display / D. Digital fuel level
indicator (the triangle on the right side of thesymbol indicates the side of the vehicle where the fuel filler is) / E. Vehicle speed
indicator (there is light sensor inside the speed indicator)
Warning light present on Diesel versions only. Diesel versions also have theicons on the display and the full scale on the
engine speed indicator is 6000 rpm.
IMPORTANT The illumination of the instrument panel graphics may vary according to version.
65J0A0006C
65

66J0A0238C
66
KNOWING THE INSTRUMENT PANEL
VERSIONS WITH RECONFIGURABLE MULTIFUNCTIONDISPLAY (right hand drive versions)
A. Engine speed indicator / B. Digital engine coolant thermometer / C. Reconfigurable multifunction display / D. Digital fuel level
indicator (the triangle on the right side of thesymbol indicates the side of the vehicle where the fuel filler is) / E. Vehicle speed
indicator (there is light sensor inside the speed indicator)
Warning light present on Diesel versions only. Diesel versions also have theicons on the display and the full scale on the
engine speed indicator is 6000 rpm.
IMPORTANT The illumination of the instrument panel graphics may vary according to version.