2018 JEEP RENEGADE lights

Light bulbsType Power
Front ceiling lightC5W 5 W
Front ceiling light (shade flaps) C5W 5 W
Rear ceiling light (versions without sun roof) C5W 5 W
Rear ceiling lights (versions with openable roof) C5W 5 W
Luggage compartment light W5W 5 W
Glove compartment lightW5W 4 W
195

REPLACING AN EXTERNAL BULB
Front upper light group (halogen high/low
beams)
To replace the bulb, proceed as follows:
working from inside the engine
compartment, remove cover A fig. 142,
using the dedicated tab;
turn the bulb and bulb holder
assembly B fig. 143 anticlockwise and
then remove it sliding it outwards;
remove, sliding it outwards, the bulb
and bulb holder assembly C fig. 144,
disconnecting it from connector D;
install the new bulb and bulb holder
assembly, ensuring that it is locked
correctly;
then insert the bulb and bulb holder
assembly in its housing and turn it
clockwise, making sure that it is locked
correctly.
Front upper light group (Xenon gas emitting
high/low beams)
For this replacement, please refer to the
Jeep Assistance network.
Front lower light cluster
Parking light/daytime running lights
(D.R.L.) and front directional indicators
To replace the bulbs, proceed as follows:
steer the wheels completely;using the screwdriver, undo screws A
fig. 145 and remove flap B;
142J0A0260C
143J0A0261C
144J0A0414C
196
IN AN EMERGENCY

remove electrical connectors C
fig. 146;
turn anticlockwise (on the left device)
or clockwise (on the right device) and
remove the bulb and bulb holder
assemblies fig. 147: D = side
lights/daytime running lights (DRLs), E =
direction indicators;
replace the burnt bulb: to extract it,
press lightly on it (1 fig. 148 ) and at the
same time turn it counter-clockwise (2);
insert the new bulb, by pressing it
fig. 148 and turning it clockwise, making
sure that it locks correctly;
then insert the bulb and bulb holder
assemblies in their respective housings
and turn them anticlockwise (right side)
and clockwise (left side), ensuring that
they are locked correctly;
reconnect the electrical connectors;finally, refit flap B fig. 145, fully
tightening fixing screws A.
Front fog lights
To replace the bulbs, proceed as follows:
steer the wheels completely;using the screwdriver, undo screws A
fig. 149 and remove flap B;
145J0A0211C
146J0A0306C
147J0A0263C
148J0A0264C
197

using tab C fig. 150, remove electrical
connector D;
turn the light bulb and holder E
fig. 150 counter-clockwise and replace
the bulb;
insert the new bulb and holder group,
making sure it is properly blocked;
reconnect the electrical connection;finally replace flap B fig. 149,
screwing down the attachment screws A
completely.
Side turn light
Side direction indicators on door mirrors
(where provided)
For light bulb replacement, please refer
to Jeep Assistance Network.
Rear upper light group
This contains the parking lights, brake
lights and directional indicators.
To replace the bulbs, proceed as follows:
open the tailgate;with the point indicated with an
arrows, remove flap A fig. 151;
unscrew fixing device B fig. 152;disconnect the electrical connector,
working on device C;
149J0A0211C
150J0A0301C
151J0A0637C
198
IN AN EMERGENCY

remove the rear light group,
unscrewing towards the outside as shown
in fig. 153;
undo the four fixing screws D
fig. 154 and remove the bulb holder
unit;
replace the bulb involved (fig. 155:
E/G = brake lights, F = directional
indicators) (bulbs E and G always light
up at the same time);
fit the new bulb, making sure it is
correctly locked;
correctly remount the bulb holder
group for the rear light group, screwing
the four attaching crews tightly;
reposition the rear light cluster on the
car;
screw the attachment device for the
rear light group tightly and reconnect the
electrical connections;
refit flap A fig. 151, ensuring that it
locks correctly;
finally, close the tailgate.
152J0A0296C
153J0A0316C
154J0A0268C
155J0A0270C
199

Rear lower light cluster
These contain the rear fog light bulbs
(left side) and reversing light bulbs (right
side).
To replace the bulbs, proceed as follows:
using the screwdriver, unscrew screws
A fig. 156 and B and remove flap C;
upper screw A is easy to access,
whereas for lower screw B it is necessary
to incline the blade of the screwdriver
appropriately as illustrated in fig. 157;
turn bulb holder D
fig. 158 anticlockwise and replace the
bulb concerned;
fit the new bulb, making sure it is
correctly locked;
refit the bulb holder in its housing and
turn it clockwise, making sure that it
locks correctly;
refit flap C correctly, completely
tightening the screws.
3
rdbrake lights
The 3rdbrake lights are LED-based. To
replace them, contact a Jeep Dealership.
Number plate lights
To replace the bulbs, proceed as follows:
remove lenses A fig. 159;turn the bulb holder clockwise and
remove the bulb;
156J0A0212C157J0A0213C
158J0A0302C
200
IN AN EMERGENCY

LUGGAGE COMPARTMENT FUSE BOXfig. 167
COMMENT The luggage compartment control unit varies according to the car's equipment.
Fuse holder control unit no. 1
USERSFUSE AMPERE
Hi-Fi system F2 20
Electric sunroof F3 20
Electric front seat lumbar regulation (driver's side) F4 7.5
Electric front seat movement (driver's side) F5 30
Electric front seat movement (driver's and passenger's sides) F6 7.5
Electric front seat lumbar support (driver's and passenger's
sides)F7 30
Front seat electric heating F8 20
In addition, the control unit has a 20A fuse to protect the sunroof panel.
Fuse holder control unit no. 2
USERSFUSE AMPERE
Control unit for external light control on trailer F1 10
Control unit for external lights (left side) F5 15
Control unit for external lights (right side) F6 15
208
IN AN EMERGENCY

CHANGING PROCEDURE
Proceed as follows:stop the car in a position that does
not cause any danger to traffic and lets
you change the tire in safety, as far as
possible from the edge of the driving
lane. The ground must be flat and
sufficiently compact;
engage the hazard warning lights and
the electric parking brake;
engage first gear or reverse or, for
versions with automatic transmission,
move the lever to position P (Park);
stop the engine and put on the
reflective safety jacket (for your own
safety and in compliance with national
laws) before getting out of the vehicle.
The motor must be kept off as long as
the car is lifted off the ground.
The spare tire, or depending on the
version, the temporary spare tire, are
located under the covering carpet in the
boot fig. 168.To access the tire or spare tire, proceed
as follows:
open the boot door, grab device A
fig. 169 and lift load platform B up,
holding it with one hand;
grab handle C fig. 170 and lift up the
covering carpet;
168J0A0338C169J0A0284C
170J0A0365C
210
IN AN EMERGENCY