122
Moving off
F Select position N.
F P ress the brake pedal firmly.
F
S
tart the engine.
If the engine does not start:
F
Sel
ect automated mode (position A ),
manual mode (position M ) or reverse
(position R ).
F
R
elease the parking brake.
F
G
radually release the brake pedal. Depending on the type of electronic
gearbox, vehicles may be able to move
immediately.
F
Accelerate.Do not press the brake and accelerator
pedals simultaneously.
Braking and accelerating must be done
with the right foot only.
Pressing the two pedals at the same time
risks damaging the gearbox.
If your vehicle has an electronic gearbox,
never try to start the engine by pushing
the vehicle.
Creep function (depending on
equipment)
This function facilitates manoeuvring of the
vehicle at low speed (when parking, in traffic
jams, etc.).
With the gear selector in position A , M or R,
the vehicle moves as soon as you take your
foot off the brake pedal , at low speed and
with the engine at idle.
Automatic mode
F Select position A .
The instrument panel displays
AUTO along with the gear engaged.
The gearbox then operates in auto-active
mode, without any inter vention on the part
of the driver. It continuously selects the most
suitable gear according to the following
parameters:
-
f
uel consumption optimisation,
-
t
he style of driving,
-
r
oad conditions,
-
v
ehicle load.
For optimum acceleration, when overtaking
another vehicle for example, press the
accelerator pedal fully down, beyond the point
of resistance.
N appears in the instrument panel.
-
If
N is flashing in the
instrument panel, move the
gear selector to position A
then to position N .
-
I
f this warning lamp comes
on, accompanied by an
audible signal, and the
display of a
message, press
more firmly on the brake
pedal.
AUTO and 1, 1
or R appear in the
instrument panel. When the engine is running, never leave
children in the vehicle without super vision.
The creep function may be temporarily
unavailable if the clutch temperature is too
high or the slope too steep.
06
Driving
1
7-inch touch screen tablet
GPS satellite navigation –
Multimedia audio system –
Bluetooth
® telephone
Contents
First steps
2
S
teering mounted controls
3
M
enus
3
N
avigation
4
R
adio
7
D
AB radio (Digital Audio Broadcasting)
9
M
edia
9
S
ettings
1
1
Connected services
1
2
Telephone
1
4
Frequently asked questions
1
7The system is protected in such a
way that
it will only operate in your vehicle.
As a safety measure, the driver should
only carry out operations that require
close attention with the vehicle stationary.
The display of the energy economy mode
message signals that the system is about
to go into standby. For more information,
refer to the "Energy economy mode"
section.
7-inch touch screen tablet
7
Visit www.dsautomobiles.com for more
information (compatibility, more help, etc.).
Activate the Bluetooth
® function on the
telephone and ensure that it is "visible to all"
(telephone configuration).
Press the MENU button.
In the menu, select:
-
" Bluetooth
®: Telephone –
Audio "
-
" Bluetooth
® configuration "
-
" Perform a
Bluetooth® search "
A window is displayed with a
search in progress
message.
The services available depend on
the network, the SIM card and the
compatibility of the Bluetooth
® devices
used.
Check the instructions for your telephone
and with your ser vice provider for the
ser vices to which you have access.
The first 4
telephones recognised are displayed
in this window. The "
Telephone " menu permits access to the
following functions in particular: " Directory", if
your telephone is fully compatible, " Calls list",
" Consult the paired equipment ".
Select the telephone to be connected from the
list. Only one telephone can be connected at
a time.
Confirm with OK.
A message on the screen indicates the
telephone chosen. To accept the pairing, enter
the same code on the telephone, then confirm
with OK.
In case of failure, the number of attempts is not
restricted.
A message that the pairing has been
successful appears in the screen. A virtual keypad is displayed in the screen:
enter a code with at least 4 digits.
Authorised automatic connection is only active
after the telephone has been configured.
The directory and the call list can be accessed
after the necessary synchronisation period.
Receiving a call
An incoming call is announced by a ring and
a superimposed display in the screen.
Select the " YES" tab in the screen
using the buttons.
Confirm with OK.
Press this button at the steering
mounted controls to accept the call.
Making a call
From the menu " Bluetooth®: Telephone –
Audio ".
Select " Manage the telephone call".
Select " Call".
Or
Select " Calls list ".
Or
Select " Directory ".
Press this button for more than two
seconds for access to your directory,
then navigate using the thumbwheel.
Audio system
