2018 CITROEN DISPATCH SPACETOURER wheel

240
Snow chains
In wintry conditions, snow chains improve
traction as well as the behaviour of the vehicle
when braking.The snow chains must be fitted only to the
front wheels.
Take account of the legislation in force in
your country on the use of snow chains
and the maximum authorised speed. Use only the chains designed to be fitted to the
type of wheel fitted to your vehicle:
You can also use snow socks.
For more information, contact a CITROËN
dealer or a qualified workshop.
Installation tips
F Move off gently and drive for a few
seconds, without exceeding around 30 mph
(50


km/h).
F

S
top your vehicle and check that the snow
chains are correctly tightened.
Original tyre size Type of chain
215/65


R16 12

mm link
215/60


R17 KONIG K-SUMMIT
VA N K8 4
2 2 5 / 5 5


R17
F

I

f you have to fit the chains during a journey,
stop the vehicle on a flat sur face on the side
of the road.
F

A

pply the parking brake and if necessary
put wheel chocks against the wheels to
prevent your vehicle from sliding.
F

F

it the chains following the instructions
provided by the manufacturer. Avoid driving with snow chains on roads
that have been cleared of snow, to avoid
damaging your vehicle's tyres and the
road sur face. If your vehicle is fitted with
alloy wheels, check that no part of the
chain or its fixtures is in contact with the
wheel rim.
It is strongly recommended that before
you leave, you practise fitting the snow
chains on a level and dry sur face.
Practical information

258
These tools are specific to your vehicle
and may vary according to its equipment.
Do not use them for any other purpose.
1.
Wheelbrace.
For removing the wheel bolts and raising/
lowering the jack.
2. Jack.
Used to raise the vehicle.
3. Wheel bolt cap/hub cap removal tools.
If your vehicle is fitted with it, it removes
the wheel bolt head covers on alloy
wheels or the hub cap on steel wheels.
4. Socket for the wheel security bolts.For
adapting the wheelbrace to the special
"security" bolts.
5. Towing eye.
Temporary puncture
repair kit
This kit comprises a compressor and a sealant
cartridge.
It allows the temporary repair of a tyre.
You are then able to go to the nearest garage.
It is designed to repair most punctures which
could affect the tyre, located on the tyre tread
or shoulder.
Its compressor can be used to check and
adjust the pressure of the tyre.
Access to the kit
For more information on the Tool box ,
refer to the corresponding section.
List of tools
These tools are specific to your vehicle and
may vary according to the level of equipment.
Do not use them for any other purposes.
This kit is stowed in the tool box. 1.
12
V compressor.
Contains a sealant cartridge for the
temporary repair of a tyre and can also
be used for adjusting tyre pressures.
2. Towing eye.
For more information on To w i n g , refer to
the corresponding section.
With a spare wheel
In the event of a breakdown

259
The vehicle's electric system allows the
connection of the compressor for long
enough to inflate a tyre after a puncture
repair.
Only use the two 12 V sockets, located at
the front , to connect your compressor.
Kit content description
C.Deflation button.
D. Pressure gauge (in bar and psi).
E. Compartment housing a cable with an
adaptor for a 12
V socket.
F. Sealant cartridge.
G. White pipe with cap for repair and
inflation.
H. Speed limit sticker.
The speed limit sticker must be affixed to
the vehicle's steering wheel to remind you
that a wheel is in temporary use.
Do not exceed a speed of 50
mph
(80
km/h) when driving with a tyre repaired
using this type of kit.Repair procedure
1. Sealant
F Turn selector A to the "sealant" position.
F

C
heck that switch B is in
position O.
Avoid removing any foreign bodies which
have penetrated into the tyre.
The tyre inflation pressures are given on
this label.
F

S

witch off the ignition.
A. "Sealant" or "Air" position selector.
B. On I/off O switch.
8
In the event of a breakdown

263
Should the pressure of one or more tyres
be adjusted, it is necessary to reinitialise
the under-inflation detection system.
For more information on Under-inflation
detection, refer to the corresponding
section.
Spare wheel
Access to the tools
For more information on the Tool box ,
refer to the corresponding section.
List of tools
F Connect the compressor's electrical connector to the vehicle's 12 V socket.
F

S
tart the vehicle and leave the engine
running.
F

A
djust the pressure using the compressor
(to inflate: switch B in position I; to deflate:
switch B in position O and press button C ),
according to the vehicle's tyre pressure
label.
F

R
emove the kit then stow it. 1.
Wheelbrace.
For removing the wheel bolts and raising/
lowering the jack.
2. Jack.
Used to raise the vehicle.
3. Wheel bolt cover/trim removal tool.
If your vehicle is fitted with it, it removes
the wheel bolt covers on alloy wheels or
the hub cap on steel wheels.
4. Socket for the wheel security bolts.
For adapting the wheelbrace to the
special "security" bolts.
5. Towing eye.
The tools are stowed in the tool box.
8
In the event of a breakdown

264
For more information on To w i n g, refer to
the corresponding section.
All of these tools are specific to your
vehicle and can vary according to the level
of equipment.
Do not use them for any other purposes.
The jack must only be used to change
a wheel with a damaged or punctured tyre.
Do not use any jack other than the one
supplied with this vehicle.
If the vehicle does not have its original
jack, contact a CITROËN dealer or a
qualified workshop to obtain the correct
jack for it.
The jack meets European standards,
as defined in the Machinery Directive
2006/42/EC.
The jack does not require any
maintenance.Access to the spare wheel
F Access to the spare wheel is from the rear.
F O pen the side-hinged rear doors or the
tailgate according to the configuration of
your vehicle.
To avoid any unwanted opening of the
electric side door(s), deactivate the
" Hands-Free Tailgate Access " function
in the vehicle configuration menu.
For more information on the Hands-
free sliding side door , refer to the
corresponding section. F

I
f your vehicle is fitted with a towbar, raise
the rear of the vehicle using the jack (must
be at jacking point B ) to allow sufficient
space to remove the spare wheel.
Removing
F Access the carrier bolt, located on the rear door sill.
In the event of a breakdown

265
F Turn the bolt anti-clockwise using the wheelbrace (about 14 turns) until the carrier
is low enough to allow the carrier hook to be
disengaged.
F

R
elease the carrier from the hook, take the
spare wheel and place it next to the wheel
to be changed.
RefittingTyre in the carrier
If you want to change the size of the tyre on the
spare wheel, follow the instructions below.
A punctured tyre of size 215
or 225 can be
placed in the carrier.
F

P

osition the wheel facing the carrier.
F

P

rogressively return the wheel to the carrier
by pushing alternately from left to right until
it is clear of the hook fixing area.
F

E

ngage the carrier on the hook, then tighten
the bolt using the wheelbrace until the bolt
is fully home.
Original tyre size XS - M XL
215/65


R16 Placing a 225

wheel in the
carrier is prohibited.
There is no restriction.
215/60


R17
215/60

R17

M&S
2 2 5 / 5 5


R17 Placing a 215

wheel in the
carrier is not recommended (risk of noise).
8
In the event of a breakdown

266
Removing a wheel
Parking the vehicle
Park the vehicle where it does not block
traffic: the ground must be level, stable
and non-slippery.
With a manual gearbox, engage first gear
then switch off the ignition to block the
wheels.
With an automatic gearbox, place the gear
selector to position P then switch off the
ignition to block the wheels.
With an electronic gearbox, place the gear
selector to position A then switch off the
ignition to block the wheels.
Apply the parking brake and check that
the warning lamp is on in the instrument
panel.
The passengers must get out of the
vehicle and wait where they are safe.
Never go underneath a vehicle raised
using a jack; use an axle stand.F

P
lace the foot of the jack on the ground and
ensure that it is directly below the A or B
jacking point provided on the underbody,
whichever is closest to the wheel to be
changed.
Do not use:
-

t
he jack for any other purpose than
lifting the vehicle,
-

a j
ack other than the one supplied by
the manufacturer.
F

I
f your vehicle has steel wheels, remove the
hub cap using tool 3 .
F

I
f your vehicle has alloy wheels, remove the
cap from each wheel bolt using tool 3 .
F

I
f your vehicle has security wheel bolts, fit
security bolt socket 4
to wheelbrace 1 to
slacken the security bolt.
F

S
lacken (without removing) the other wheel
bolts using just wheelbrace 1 .
In the event of a breakdown

267
F Raise the vehicle using wheelbrace 1, until
there is sufficient space between the wheel
and the ground to admit the spare (not
punctured) wheel easily. Ensure that the jack is stable. If the
ground is slippery or loose, the jack may
slip or collapse – Risk of injury!
Ensure that the jack is positioned only
at one of jacking points A or B under the
vehicle, making sure that the vehicle's
contact sur face is centred on the head
of the jack. Other wise there is a risk of
damage to the vehicle and/or of the jack
dropping – Risk of injury!
F
R
emove the bolts and keep them in a clean
place.
F
R
emove the wheel.
Fitting a wheel
F Put the wheel in place on the hub.
F
S crew in the bolts by hand to their stop.
F

I
f your vehicle is so equipped, pre-tighten
the security bolt using the wheelbrace
1
fitted with the security socket 4 .
F

P
re-tighten the other bolts using
wheelbrace 1
o n l y.
F

E

xtend jack 2
, using the hand wheel, until
its head comes into contact with jacking
point A or B used, with the contact
sur face A or B on the vehicle correctly
engaged with the central part of the head
of the jack.
8
In the event of a breakdown