2018 BMW X2 Owners Manual

'xDate: update.'xGlass sunroof: initialize the system.
Disposing
of
old
batteriesHave old batteries disposed of by a dealjerss service center or another qualifiedservice center or repair shop or take
them to a collection point.
Maintain the battery in an upright position for
transport and storage. Secure the battery so that
it does not tip over during transport.
Fuses
Safety
information
WARNING
Incorrect and repaired fuses can overload elecj
trical lines and components. There is a risk of
fire. Never attempt to repair a blown fuse. Do not replace a nonworking fuse with a substituteof another color or amperage rating.
Accessing
the
fuses
The fuses are located in the glove compartment.
1.Open the glove compartment.2.Swing the cover down, arrow.
Information on the fuse types and locations, as well as the positions of any other fuse boxes, is
found on a separate sheet in the fuse box.
Replacing
fuses
The vehicle manufacturer recommends that youhave a dealer's service center or another qualij
fied service center or repair shop replace the fuses.Seite 281Replacing
componentsMOBILITY281
Online Edition for Part no. 01402989448 - II/18

Breakdown
assistanceVehicle
features
andoptions
This chapter describes all standard, country-spejcific and optional features offered with the series. It also describes features that are not necessarilyavailable in your vehicle, e. g., due to the selectedoptions or country versions. This also applies to
safety-related functions and systems. When usj
ing these functions and systems, the applicable laws and regulations must be observed.
Hazard
warning
flashers
The button is located in the center console.
The red light in the button flashes when the hazj ard warning flashers are activated.
Warning
triangle
The warning triangle is located on the inside ofthe tailgate.
Move the warning triangle sideways and remove it.
First-aid
kit
General
information
Some of the articles have a limited service life.
Check the expiration dates of the contents reguj
larly and replace any expired items promptly.
Storage
The first-aid kit is located beneath the cargo floorpanel.
Seite 282MOBILITYBreakdown
assistance282
Online Edition for Part no. 01402989448 - II/18

Emergency
Request
Intelligent
emergency
callConcept
In case of an emergency, an Emergency Rej
quest can be triggered automatically by the sysj tem or manually.
Intelligent emergency call establishes a connecj tion with the BMW Response Center.
General
information Only press the SOS button in an emergency.
For technical reasons, the Emergency Request
cannot be guaranteed under unfavorable condij
tions.
Overview
SOS button in the roofliner.
Functional
requirements
'xThe Assist system is functional.'xThe ignition is switched on.'xIf the vehicle is equipped with intelligent emergency call: the SIM card integrated in
the vehicle has been activated.
Automatic
triggering
Under certain conditions, for instance if the airj bags trigger, an Emergency Request is automatij
cally initiated immediately after an accident of
corresponding severity. Automatic Collision Notij
fication is not affected by pressing the SOS butj
ton.
Manual
triggering1.Touch the cover.2.Press and hold the SOS button until the LED
on the button illuminates green.'xThe LED is illuminated green when an Emerj
gency Request has been initiated.
If a cancel prompt appears on the Control Display, the Emergency Request can be
aborted.
If the situation allows, wait in your vehicle until the voice connection has been established.'xThe LED flashes green when a connection to
the BMW Response Center has been estabj
lished.
The BMW Response Center then makes contact with you and takes further steps to
help you.
Even if you are unable to respond, the BMW Response Center can take further steps tohelp you under certain circumstances.
For this, data is transmitted to the BMW Rej
sponse Center which serves to determine the
necessary rescue measures. E.g., the current
position of the vehicle, if it can be established.
Even if you can no longer hear the BMW Rej
sponse Center through the loudspeakers, the
BMW Response Center may still be able to
hear you.
The BMW Response Center ends the Emerj
gency Request.
Jump-starting
General
information If the battery is discharged, the engine can bestarted using the battery of another vehicle andtwo jumper cables. Only use jumper cables withfully insulated clamp handles.
Seite 283Breakdown
assistanceMOBILITY283
Online Edition for Part no. 01402989448 - II/18

Safety
information
DANGER
Contact with live components can lead to an electric shock. There is a risk of injuries or danj
ger to life. Do not touch any components that
are under voltage.
WARNING
If the jumper cables are connected in the incorj rect order, sparking may occur. There is a risk
of injury. Pay attention to the correct order durj
ing connection.
NOTE
In the case of body contact between the two vehicles, a short circuit can occur during jump-
starting. There is a risk of damage to property.
Make sure that no body contact occurs.
Preparation
1.Check whether the battery of the other vehij
cle has a voltage of 12 volts. The voltage inj
formation can be found on the battery.2.Switch off the engine of the assisting vehicle.3.Switch off any electronic systems/power conj
sumers in both vehicles.Starting
aid
terminals
The starting aid terminal in the engine compartj
ment acts as the battery's positive terminal.
Open the cover of the starting aid terminal.
A special connection on the body acts as the
battery negative terminal.
Connecting
the
cables To prevent personal injury or damage to both vejhicles, adhere strictly to the following procedure.
1.Pull off the lid of the BMW starting aid termij
nal.2.Attach one terminal clamp of the positive
jumper cable to the positive terminal of the battery, or to the corresponding starting aid
terminal of the vehicle providing assistance.3.Attach the terminal clamp on the other end of the cable to the positive terminal of the batjtery, or to the corresponding starting aid terjminal of the vehicle to be started.4.Attach one terminal clamp of the negativejumper cable to the negative terminal of theSeite 284MOBILITYBreakdown
assistance284
Online Edition for Part no. 01402989448 - II/18

battery, or to the corresponding engine or
body ground of assisting vehicle.5.Attach the second terminal clamp to the negj
ative terminal of the battery, or to the correj sponding engine or body ground of the vehij
cle to be started.
Starting
the
engine
Never use spray fluids to start the engine.
1.Start the engine of the assisting vehicle and let it run for several minutes at an increased
idle speed.2.Start the engine of the vehicle that is to be
started in the usual way.
If the first starting attempt is not successful, wait a few minutes before making another atj
tempt in order to allow the discharged battery
to recharge.3.Let both engines run for several minutes.4.Disconnect the jumper cables in the reverse order.
Check the battery and recharge, if needed.
Tow-starting
and
towing
Safety
information
WARNING
Due to system limits, individual functions can malfunction during tow-starting/towing with the Intelligent Safety systems activated. There is a
risk of an accident. Switch all Intelligent Safety
systems off prior to tow-starting/towing.
Steptronic
transmission
without
xDrive:
transporting
the
vehicle
General
information
The vehicle must not be towed if the front wheels are touching the ground.
Safety
information
NOTE
The vehicle can be damaged when towing the
vehicle with a lifted rear axle. There is a risk of
damage to property. Have vehicle transported
only with lifted front axle or on a loading platj
form.
Pushing
the
vehicle
To remove a broken-down vehicle from the danj
ger area, it can be pushed for a short distance.
Roll or push, refer to page 124, the vehicle.
Tow
truck
Your vehicle should be transported with a tow truck with a so-called lift bar or on a flat bed.
NOTE
The vehicle can become damaged when lifting
and securing it.
There is a risk of damage to property.
'xLift the vehicle using suitable means.'xDo not lift or secure the vehicle by its tow fitting, body parts, or suspension parts.
Steptronic
transmission
with
xDrive:
transporting
the
vehicle
General
information The vehicle is not permitted to be towed.
Seite 285Breakdown
assistanceMOBILITY285
Online Edition for Part no. 01402989448 - II/18

Pushing
the
vehicle
To remove a broken-down vehicle from the danj
ger area, it can be pushed for a short distance.
Roll or push, refer to page 124, the vehicle.
Tow
truck
The vehicle should only be transported on a loading platform.
NOTE
The vehicle can become damaged when lifting
and securing it.
There is a risk of damage to property.
'xLift the vehicle using suitable means.'xDo not lift or secure the vehicle by its tow
fitting, body parts, or suspension parts.
Towing
other
vehicles
General
information Switch on the hazard warning system, dependj
ing on local regulations.
If the electrical system has failed, clearly identify
the vehicle being towed by placing a sign or a warning triangle in the rear window.
Safety
information
WARNING
If the approved gross vehicle weight of the towj ing vehicle is lighter than the vehicle to be
towed, the tow fitting can tear off or it will not
be possible to control the vehicle's response.
There is a risk of an accident! Make sure that the gross vehicle weight of the towing vehicle is
heavier than the vehicle to be towed.
NOTE
If the tow bar or tow rope is attached incorj
rectly, damage to other vehicle parts can occur.
There is a risk of damage to property. Correctly
attach the tow bar or tow rope to the tow fitting.
Tow
bar
The tow fittings used should be on the same
side on both vehicles.
Should it prove impossible to avoid mounting the tow bar at an offset angle, please follow the foljlowing:
'xManeuvering capability is limited goingaround corners.'xThe tow bar will generate lateral forces if it issecured with an offset.
Tow
rope
When starting to tow the vehicle, make sure that the tow rope is taut.
Use nylon ropes or straps, which will enable the
vehicle to be towed without jerking.
Seite 286MOBILITYBreakdown
assistance286
Online Edition for Part no. 01402989448 - II/18

Tow
fitting
General
information
The screw-in tow fitting should always be carried
in the vehicle.
The tow fitting can be screwed in at the front or
rear of the vehicle.
The tow fitting and the onboard vehicle tool kit, refer to page 273, are together in the cargo area.
Use of the tow fitting:
'xUse only the tow fitting provided with the vej hicle and screw it all the way in.'xUse the tow fitting for towing on paved roadsonly.'xAvoid lateral loading of the tow fitting, for inj
stance do not lift the vehicle by the tow fitj ting.
Safety
information
NOTE
If the tow fitting is not used as intended, there
may be damage to the vehicle or to the tow fitj ting. There is a risk of damage to property. Folj
low the notes on using the tow fitting.
Screw
thread
for
tow
fitting
Press on the mark on the edge of the cover to
push it out.
Tow-starting
Steptronic
transmission Do not tow-start the vehicle.
Tow-starting the engine is not possible due to
the Steptronic transmission.
Have the reasons for the starting difficulties corj
rected by a dealerss service center or another
qualified service center or repair shop.
Seite 287Breakdown
assistanceMOBILITY287
Online Edition for Part no. 01402989448 - II/18

CareVehicle
features
andoptions
This chapter describes all standard, country-spejcific and optional features offered with the series. It also describes features that are not necessarilyavailable in your vehicle, e. g., due to the selectedoptions or country versions. This also applies to
safety-related functions and systems. When usj
ing these functions and systems, the applicable laws and regulations must be observed.
Washing
the
vehicle
General
information
Regularly remove foreign objects such as leaves
in the area below the windshield when the hood
is raised.
Wash your vehicle frequently, particularly in winj
ter. Intense soiling and road salt can damage the
vehicle.
Steam
blaster
and
high-pressure
washer
Safety
information
NOTE
When cleaning with high-pressure washers,
components can be damaged due to the presj sure or temperatures being too high. There is a
risk of damage to property. Maintain sufficient
distance and do not spray too long continuj
ously. Follow the operating instructions for the
high-pressure washer.
Distances
and
temperature'xMaximum temperature: 140