2018 AUDI Q3 hood open

0 co ......
"' ,....
"' ...... 0 0 :::,
00
E lect romechanical pa rking brake
¢ page 12
Tire Pressu re Monitoring System *
../
¢page 183
Tire press ure monitor ing system*
¢page 183
Elect ronic power control ../
¢ page 14
M alfunct ion Indica to r L amp (M IL)
../
¢ page 14
En gine speed limi tation*
¢page 15
E ng ine o il level
¢page 15
Eng ine oi l sensor
¢ page 15
Battery charge
¢ page 13
Tank system
e> page 15
Washer fluid level *
¢ page 15
E ng ine start system
¢page 15
E lect romechani cal s teer ing../
¢ page93
S teer ing lock
¢ page 13
Remote con trol key*
¢ pag e 63
Battery in remote control key
¢ page23
Bulb failure indicator
¢page 16
H eadlight range contro l system
¢ page 16
A daptive light *
¢ page 16
Li ght/rai n sensor *
¢ page 16
Instruments and ind icator lights
S usp ension contro l*
¢ page 16
USA models:
Speed warning system*
¢page
76
Canada models:
Speed wa rning system*
¢ page
76
Other indicator lights
--------------Turn s ignals
¢page 16
Trailer t urn signa ls*
¢ page 16
USA models:
Cruise control system
¢page
76
Canada models:
Cru ise control system
¢ page
76
Hill des ce n t assis t*
¢page 91
Remo te co ntro l key*
¢ page 63
High beams
¢ page34
Door open
¢ page 17
Hood open
¢ page 17
L u ggage compartment lid ope n
¢ page 17
BRAKE/(©) Brake system
If this indica to r li ght tur ns on, t here is a malf unc­
tion in the brake system.
llll vehicle and check brake fluid level
Stop t he vehicle and check the brake fl uid level.
See a n author ized Audi dealer or author ized A udi
Service Facility for assis tance if necessa ry .
1111 (USA models ) /. (Canada models)
Brake: malfunction! Please park vehicle safely .,.
11

Instruments and indicator lights
If the ABS indicato r light LtiiJ (U SA mode ls)/ li]
(Canada models) , the ESC ind icator light
Dl and
the brake system ind icator light
1111 ( U SA mod­
els)/ . (Canada models) all turn on and this
message appears , then the ABS, ESC and braking
d istr ibut io n are malfunctioning ¢,&. .
Do not cont inue driving . See an autho rized Aud i
dealer or authori zed Aud i Serv ice Facility for as­
sistance ¢,&. .
1111 (USA models )/. (Can ada model s) Park­
ing brake: System fault! See owner 's manual
-If the indica tor l ight and the message appear
when the vehicle is stationar y or after sw itch­
ing the ignitio n on ,
check if you can release the
parking b rake.
If you cannot re lease the park­
ing brake, see an authori zed Aud i dea ler or au­
thori zed Audi Serv ice Facility. If you can rele ase
the parking brake and the message still ap ­
pears, see an autho rized Aud i dealer or author­
ized Audi Service Facility immed iately to have
the malfunction corrected.
- If the indicator l ight and message appea r while
dri vin g ,
the hill start assist or emergency brak­
ing func tion may be malfunctioning. It may not
be possib le to set the parking brake or release
it once it has been set . Do not park your veh icle
on hi lls. See an authorized Audi dealer or au­
thorized Audi Service Facility for assistance .
Applies to: USA models
If t he 1111 and EiJ indicator lights turn on a t the
same time, the brake pads are worn out
¢ page 14.
& WARNING
-Read and follow the warn ings in
¢ page 155, Working in the engine com­
partment
before open ing the hood and
check ing the b rake fl uid level.
- If the brake system indicator light does not
turn off or it t urns on while driv ing, the
brake fluid level in the reservoir is too low ,
and this increases the risk of an acc ident .
Stop the vehicle and do not continue dr iv­
ing. See an author ized Audi dealer or au­
tho rized Aud i Serv ice Facility fo r ass ist ance.
12
- If the brake system indicator light t urns on
together w ith the ABS and ESC indicator
lights, the ABS/ESC regu lating function may
be malfunct ion ing . Fu nctions that stabilize
the vehicle are no longer available . This
could cause the vehicle to swerve, which in­
creases the risk that the vehicle will slide.
Do not co nt inu e d rivi ng. See an autho rize d
Aud i dea ler or a uthorized Aud i Serv ice Facili ­
ty for ass istance .
PARK/<®) Electromechanical parking brake
If the -(USA mode ls) I. (Canada models)
i ndicato r light turns on, the parking brake was
set.
- (USA model s) /. (Can ada model s) Pre ss
brake pedal to r ele a se parking brake
To release the parking brake , press the brake
pedal and press the(®) button at the same t ime
or start driving with hill start assist¢
page 65,
Starting from a stop.
f p j Pa rking brake: S ystem faul t! See owner' s
manual.
T here is a ma lfunction in the parking brake. Drive
to an authori zed Aud i dea ler or a uthori zed Audi
Service Facility immediate ly to have the malfunc­
tion corrected.
(D Tips
For additional informat ion on the parking
brake, see
¢ page 63.
-F-Cooling system
• Turn off engine and ch eck coolant level.
The coolant level is too low.
Do not continue driving and switch the engine
off. Check the coolant level ¢
page 162.
-If the coo lant level is too low, add coolant
¢
page 162 . Only continue driving on ce the in­
dica tor ligh t turns off .
• Coolant temperature! Let engine run with
v e hicle stationar y.

0 co ......
"' ,....
"' ...... 0 0 :::,
00
L et the engine run at idle for a few minutes to
cool off, until the indicator light turns off.
- If the indicator light does not turn off, do not
continue driving the vehicle. See an authorized
Audi dealer or authorized Audi Service Facility
for assistance .
A WARNING
-Never open the hood if you can see or hear
steam or coolant escaping from the engine
compartment. This increases the risk of
burns. Wait until you no longer see or hear
steam or coolant escap ing .
- The engine compartment in any veh icle can
be a dangerous area. Stop the engine and
allow it to cool before working in the engine
compartment. Always follow the informa­
tion found inc::>
page 155, Working in the
engine compartment.
(D Note
Do not continue driving if the. indicator
light turns on as this increases the risk of en­
gine damage.
• Turn off engine! Oil pressure is too low.
Stop the eng ine and do not continue dr iving .
Check the engine oil leve l c::>
page 160.
- If the engine oil level is too low, add engine oil
c::>page 160. Only cont inue driv ing once the in­
dicator light turns off.
- If the engine oil level is correct and the indica ­
tor light st ill turns on, turn the eng ine off and
do not continue driving. See an authorized Audi
dealer or authorized Audi Service Facility for as­
s istance.
(D Tips
The oi l pressure warning is not an o il level in­
dicator. Always check the oil level regularly.
0 Generator/vehicle battery
• Alternator fault: Battery is not being charg­
ed.
Instruments and indicator lights
T he re is a malfunct ion in the a lternator or the ve­
hicle e lectrical system.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately. Because the ve­
hicle battery is discharging, turn off all unneces­
sary electrical equipment such as the radio. See
an authorized Aud i dea ler or authorized Audi
Service Facility if the battery charge level is too low.
[•] Low battery charge: Battery will be charged
while driving.
T he starting ability may be impaired.
If this message turns off after a little while, the
vehicle battery cha rged enough while driving.
If the message does not turn off, have an author­
ized Audi dealer or author ized Audi Service Facili­
ty repair the malfunction .
,{,_ Safety belt
The . indicator light stays on until the dr iver's
and front passenge r's safety belts are buckled.
Above a certa in speed, there will a lso be a warn­
ing tone .
(D Tips
For additional informat ion on safety belts,
see c::>
page 106.
@-Steering lock
• Steering fault! Do not drive vehicle!
There is a malfunction in the electron ic steering
lock. You cannot turn the ign ition on.
Do
not tow your vehicle because it cannot be
stee red. See an author ized Audi dealer or author­
ized Audi Service Facility for assistance .
!II Steering lock: System fault! Please contact
dealer.
There is a malfunction in the e lectronic steering
lock.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediate ly to have the
malfunction corrected.
Ill>
13

a
co
...... N r--. N .-< 0 0 ::, co
/fj/c::::::::;/ c::5 Door, hood or luggage
compartment lid is open
II-If the indicator light turns on, then one of
the doors is not closed .
f-j-If the ind icator light tu rns on , then the hood
is not closed.
§-j -If the ind icator light turns on, then the lug­
gage compartment lid is not closed.
On-Board Diagnostic
System (OBD)
Malfunction indicator lamp (MIL)
The malfunction indicator lamp (MIL) ¢.j in the
instrument cluster is part of the On-Board Diag­
nostic System (OBD II).
The warning/indicator light turns on when the ig­ nition is switched on and turns off once the en­
gine is started and is running in idle at a stab le
speed. This indicates that the MIL is functioning
correct ly.
If the light does not turn off after starting the
engine
or turns on while driving, this may indi­
cate there is a malfunction in the engine.
If the
indicator turns on, the catalytic converte r may be
damaged .
Drive
with reduced engine performance (avoid
high speeds for extended periods of time and/or
fast acceleration) and have the malfunction cor­
rected. See an authorized Aud i dealer or autho r­
ized Audi Service Facility.
The MIL may also turn on if the fuel filler cap i s
not cl osed correctly
¢ page 153.
Instruments and indicator lights
On-Board Diagnostics
Fig. 5 Location o f Data Li nk Con necto r (OLC)
On-Board Diagnostics monitors the components
of your emission control system. Each monitored
component in your engine system has been as­
s igned a code. In case of a malfunction , the com­
ponent will be identified and the fault sto red as a
code in the control module memory.
The MIL light may also illuminate if there is a
leak in the on-board fuel vapor recovery system.
If the light illuminates after a refueling, stop the
vehicle and make sure the fuel f iller cap is prop­
erly closed (only vehicles with gasoline engine)
r::'.>page 153 .
In order to make an acc urat e diagnosis, the stor­
ed data can only be displayed using special diag­
nostic equipment (generic scan tool for 080).
In order to connect the special d iagnost ic equip­
ment, push the p lug into the Data Lin k Connector
(DLC). The DLC is located to the right of the hood
release ¢
fig. 5.
Your authorized Aud i dea ler or qualified work­
shop can interpret the code and perform the nec­
essary repair.
_& WARNING ~
Do not use the diagnostic connector for per-
sona l use. Incorrect usage can cause malfunc­
tions, which can increase the risk of a colli­
sion!
17

0 co ......
"' ,....
"' ...... 0 0 :::,
00
- The washer fluid nozzles for the windshie ld
washer system are heated at low tempera­
tures when the ignition is on.
- When stopping temporarily, such as at a
traffic light, the speed of the windshie ld
wipers automatically reduces by one level.
Cleaning the wiper blades
Clean the wiper blades when you see wiper
streaks. Use a soft cloth and a glass cleaner .
Windshield wiper
.. Place the windshield wiper arms in the service
pos ition ¢
page 39.
"'Fold the windshield wiper arms away from the
windshield .
Rear window wiper
.. Fold the wiper arm away from the rear window .
.&_ WARNING
Dirty windshield wiper blades can impair vi­
sion, which increases the risk of an accident.
Replacing windshield wiper blades
F ig . 41 Remov ing w inds hield w iper blades
Windshield wiper service position/blade
replacement position
.. Switch the windshield wipers off (position @
¢page 38, fig. 39) .
-
"'Switch off the ignition and hold the windshield
wiper lever in position @¢
page 38, fig. 39 un­
t il the windsh ield wiper moves into the service
pos ition .
"'T o bring the windshield wipers back to the nor­
ma l position, switch the ignition on and hold
Lights and Vision
the windshield wipe r lever in pos ition @until
the windshield wipers go back to the normal
position, or drive faster than 8 mph (12 km/h) .
Removing the wiper blade
"' Fold the windshie ld wiper arm away from the
windshield .
.. Press the locking knob
(D ~ fig . 41 on the wiper
blade . Hold the wiper blade firmly.
.. Remove the w iper blade in the direction of the
arrow.
Installing the wiper blade
"'I nsert the new wiper blade into the mount on
the wiper arm @until you hear it latch into
place.
.. Place the wiper arm back on the window.
"' To bring the wiper blades back into the original
position, switch the ignition on and operate the
w indshield w iper lever .
,&. WARNING
----
For safety reasons, the windshield wipe r
blades should be replaced once or twice each
year.
(D Note
- Only fold the w indshield w ipers away when
they are in the service pos ition . Otherwise,
you risk damaging the paint on the hood or
the windsh ield wiper motor.
- You should not move your veh icle or operate
the windsh ield wiper leve r when the wiper
arms are folded away from the windshie ld.
The windshie ld wipers wou ld move back in­
to their original position and could damage
the hood and windshie ld.
(D Tips
-You can also use the service position, for ex­
ample, if you want to protect the windshield
from icing by using a cover.
- You cannot activate the service position
when the hood is open .
39

Driving
P - Park
This selector lever position prevents the vehicle
from rolling. You can only shift into Park when
the vehicl e is
stationary ¢&. .
To shift in and out of the P selector lever posi ­
tion, press the interlock button in the selector
lever
while pressing the brake pedal.
R- Reverse
Only shift into reverse gear when the vehicle is
stationary and the engine is running at idle
speed ¢&, .
To select the R selector lever position, press the
interlock button
while pressing the brake pedal.
N - Neutral
The transmission is in idle in this position.
To engage the N selector lever position, press the
button on the selector lever and shift into the N
position.
To
move from selector lever position out of N,
you must press the brake pedal and the vehicle
must be traveling less than 1 mph (2 km/h) or be
stationary.
DIS -Normal position for driving forward
In the D/S selector lever position, the transmis­
sion can be operated either in the normal D mode
or in the S sport mode. To select the S sport
mode, pull the selector lever back briefly. Pulling
the lever back again will select the normal D
mode. The instrument cluster display shows the
selected driving mode .
In the
normal mode D, the transmission auto­
matically selects the suitable gear ratio. It de­
pends on engine load, vehicle speed and driving
style.
The engine's power reserves are used fully in the
Sport mode S. Shifting may become noticeable
when accelerating.
To
move from selector lever position N to D, you
must press the brake pedal and the vehicle must
be traveling less than 1 mph (2 km/h) o r be sta­
t ionary ¢&, .
68
A WARNING
-
Read and follow all WARNINGS.
-The vehicle can roll
even if the ignition is
switched off.
- Never select R or P while driving, because
this increases the risk of an accident.
- Power is still transmitted to the wheels
when the engine is running at idle. To pre­
vent the vehicle from "creeping", you must keep your foot on the brake in all selector
lever positions (except P) when the engine is
running .
- Do not inadvertently press the accelerator
pedal when the vehicle is stopped if a gear is
engaged . Otherwise, the vehicle will imme­
diately start to
move -sometimes even if
the parking brake is firmly applied. This in­
creases the risk of an accident.
- To reduce the risk of an accident, do not
press the accelerator pedal when changing
the selector lever position while the vehicle
is stationary and the engine is running.
- Never leave your vehicle with the engine
running while in gear. If you must leave
your vehicle when the engine is running, set
the parking brake and move the selector lev­
er to the P position.
- Before you or other persons open the hood
and work on a running engine, the selector
lever must be in the P position and the park­ ing brake must be applied to reduce the risk
of an accident . Always read and follow the
applicable warnings ¢
page 155, Working
in the engine compartment.
- Read and following all WARNINGS¢&. in
Driving tips on page 69 .
(D Note
Never let the vehicle roll downhill with engine
off and the selector lever in the N position,
because this could damage the automatic
transmission and catalytic converter.
(D Tips
- If you accidentally select N while driving,
take your foot off the accelerator pedal and .,.

a
co
...... N r--. N .... 0 0 ::, co
Fuel filler door emergency release
If the central locking system is faulty, the fuel filler door can be unlocked manually.
Fi g. 134 Right si de tr im j:>ane l in the luggage compart­
ment: emergen cy release mechani sm
The emergency opening mechanism is located
behind the right side trim panel in the luggage
compa rtme nt.
• Remove the cover in the side panel.
• Loosen the strap from its bracket -arrow- and
pull on it carefully<=:>
fig. 134 c:>(D . The filler
doo r is released .
• Press on the lef t side of the fuel fille r doo r to
open it
<=:> page 153, fig. 132 .
(D Note
Onl y pull o n the loop until you feel resi stance.
You will not he ar it relea se. O therwise yo u
co uld d amage the eme rge ncy re lea se me ch a­
nism .
Catalytic converter
The vehicle may o nly be dr iven with unleaded
gasoline, otherwise the catalyt ic converter will be
destroyed .
N ever d rive until the tank is comp letely e mpty .
The irregular supply of f uel th at resul ts from that
can cause engine m isfires. Uncombus ted f uel will
enter the exhaust system, wh ic h can cau se ove r­
heat ing and damage to the catalyt ic converter .
A WARNING
-The temperature in the ex ha ust system is
high, both when dr iving and after stopping
the engine.
-
Checking and Filling
- Never touch the exhaust tail pipes o nce they
have become hot . This cou ld resu lt in burns.
- Do not par k your vehicle over flammable
mate ria ls s uch as grass or leaves because
the high temperature of the emissions con­
trol system could start a fire.
- Do not app ly unde rbody protectant in the
exhaust system area, because this increases
the risk of fire.
Engine compartment
' Working in the engine compartment
Special care is required if you are working in the
engine compartmen t
For work in the engine compartment, such as
checking and fill ing fluids, there is a risk of in­
jury, scalding, accident s, and burns . For thi s
reason, follow all the warnings and general
s afety pre caution s provided in the following in ­
formation. The engine compartment is a dan­
gerous a rea on the vehicle .
<=:> .&.
A WARNING
-Turn the engine off .
- Sw itch th e ignition off .
- Se t the p arking brak e.
- M ove the selec tor lever i nto the P position.
- Never open the hood whe n th ere is steam o r
coo lant escaping from the engine comp art­
men t, bec ause there is a risk that yo u could
be burned. Wai t until no s te a m o r coolan t is
escaping .
- Le t t he eng ine cool down.
- Keep children away from th e eng in e com-
p ar tme nt.
- N ever sp ill fluid s on a ho t engine . These flu­
i d s (su ch as the free ze p ro te ct ion contained
in the coolant) c an catch fi re.
- Avoid short circui ts in th e electrical system.
- When working in the engine compartment,
remember that the radiator fan can swi tch
o n even if t he igni tion i s sw itched off, w hich
i n cre a ses the r is k of person al injury.
~
155

a
co
,....,
N r--. N
'"' 0 0 ::, co
Opening/closing the hood
The hood is released from inside the vehicle.
Fig. 135 Driver footwell: release lever
Fig. 136 Rocker switch under the hood
"' 0 0
0
=i
~
Make sure the wiper arms are not raised up from
the windshield. Otherwise the paint could be
damaged.
Opening the hood
.. With the driver's door open, pull the lever be­
low the instrument panel in the direction of the
arrow¢fig.135.
Checking and Filling
.. Raise the hood slightly¢,& .
.. Press the rocker switch under the hood upward
¢fig. 136. This releases the catch .
.. Open the hood.
Closing the hood
.. Push the hood down until you override the
force of the strut .
.. Let the hood fall lightly into the latch.
Do not
press it in.
c> ,&.
A WARNING
-
-Never open the hood when there is steam or
coolant escaping from the engine compart­
ment, because there is a risk that you could
be burned. Wait until no steam or coolant is
escaping.
- If the hood is not latched completely, it
could fly up while you are driving and ob­
struct your vision.
- For safety reasons, the hood must always be
closed securely while driving. Because of
this, always check the hood after closing it
to make sure it is latched correctly. The
hood is latched if the front corners cannot
be lifted.
- If you notice that the hood is not latched
while you are driving, stop immediately and
close it, because dr iving when the hood is
not latched increases the risk of an accident .
157