2018 AUDI A8 oil

Checking and Filling
Cl osing the ho od
~ Push the hood down until you override the
force of the strut .
~ Let the hood fall light ly into the latch. Do not
press it in.
c::> .&_ .
A WARNING
-Never open the hood when there is steam or
coolant escaping from the engine compart­
ment, because there is a risk that you could
be burned. Wait until no steam or coolant is
escaping.
Engine compartment overview
The most important check points .
-For safety reasons, the hood must always be
closed securely while driv ing. Because of
this, always check the hood after closing it
to make sure it is latched correctly . The
hood is latched if the front corners cannot
be lifted.
-If you notice that the hood is not latched
while you are driving, stop immed iate ly and
close
it, because d riving when the hood is
not latched increases the r is k of an accident.
Fig. 258 Typical locatio n of the rese rvoir and the engi ne o il fille r open ing
(D Washer fluid reservoir (Q) c::> page 281
@ J ump start point(-) with hex head screw
c::> page 280, c::> page 32 7
® Jump start point(+) under a cover
c::> page 280, c::> page 32 7
@ Engine oil label * w ith VW standard
c::> page 2 75
274
® Engine oil filler opening ( page 2 76
@ Brake fl uid reservo ir ((0)) c::> page 2 79
(J) Coolant reservoir (-L) c::> page 2 78
The engine oil filling opening (item @) may be
l ocated in a different area depending on the en-
gine version.
.,.

u. co ..... N
" N ..... 0 0 :c ' & WARNING
Read and follow all WARNINGS before check­
ing anything in the engine
compartment~ .&.
in Working in the engine compartment on
page 272.
Engine oil
If the engine oil level is too low
If you need to add engine oil, use an oil that is listed on the sticker.
The sticker is located at the
front of the engine
compartment ~ page 274,
fig.
258.
If the recommended engine oil is not available,
in an emergency you may add a maximum of 1
quart
(I liter) of ACEA C3 or API SN engine oil
one time until the next oil change.
For more information on the correct engine oil
for your vehicle, contact an authorized Audi deal­
er or authorized Audi Service Facility. Have the oil
changed by an authorized Audi dealer or author­ ized Service Facility.
Audi recommends
«;;castrol I /g@@g PrtfTr.:!\.7.Tri,'lAl.
Audi recommends using the Longlife high-per·
formance engine oil from Audi Genuine Parts.
Checking the engine oil level
The engine oil level can be checked in the Info­
tainment system
Observe the safety precautions ~ A in Working
in the engine compartment on page 2 72.
~ Park your vehicle on a level surface.
~ Shut the engine off when it is warm.
~ Switch only the ignition back on.
~ Wait approximately two minutes.
~ Select: the ICARI function button> (Car)* Sys­
tems
control button > Service & control > Oil
level.
~ Read the oil level in the Infotainment system .
Add engine oil if the bar in the oil level indica­
tor is just before
"min"~ page 2 76.
Checking and Filling
@ Note
The engine oil level must not be under the
"min" marking, as this will increase the risk of
engine damage.
(D Tips
The oil level indicator in the display is only an
informational display.
If the oil level is too
low, a minimum oil warning appears in the in­
strument cluster. Add oil and close the hood.
The current oil level is displayed in the Info­
tainment system the next time the ignition is
switched on.
(D Tips
The engine oil consumption may be up to
0.5 quart/600 miles (0 .5 liter/1,000 km), de­
pending on driving style and operating condi­
tions. Consumption may be higher during the
first 3,000 miles (5,000 km). Because of this,
the engine oil level must be checked regular­
ly. It is best to check each time you refuel
your vehicle and before long drives.
- In order to provide effective lubrication and
cooling of internal engine components, all
internal combustion engines consume acer­
tain amount of oil. Oil consumption varies
from engine to engine and may change sig­
nificantly over the life of the engine. Typi­
cally, engines with a specified break-in peri­
od consume more oil during the break-in pe­
riod than they consume after oil consump­
tion has stabilized.
- Under normal conditions, the rate of oil
consumption depends on the quality and
viscosity of the oil, the RPM (revolutions per
minute) at which the engine is operated, the
ambient temperature and road conditions.
Further factors are the amount of oil dilu­
tion from water condensation or fuel resi­
due and the oxidation level of the oil. As any
engine is subject to wear as mileage builds
up, the oil consumption may increase over
time until replacement of worn components
may become necessary.
.,.
275

Checking and Filling
-With all these variables coming into play,
no standard rate of o il consumption can be
established or specified. There is no alterna­
tive to checking the oil level regularly and
frequently.
- If you have the impression your engine con­
sumes excessive amounts of oil, we recom­
mend that you consult an authorized Audi
dealer to have the cause of your concern properly diagnosed . Keep in mind that the
accurate measurement of oil consumption
requires great care and may take some
time. An authorized Audi dealer has instruc­
tions about how to measure oil consump­
tion accurately.
- You can find information on engine oil and
engine oil capacities for the USA at
www.audiusa.com/help/maintenance, or
for Canada at www.audi.ca/ca/web/en/
customer-area/ care-a nd-maintena nee/ aud
i­
service-schedules. html , or call
800 -822-2834.
Adding engine oil
Fig. 259 Engine co mpartment : en gin e oil fille r opening
c ove r
0 N
-N ,.:
gi
Observe the safety precautions c::, &. in Working
in the engine compartment on page
2 72.
"Turn the engine off.
" Open the hood c::, page 2 73.
" Unscrew the cap 't=?1 for the engine oil filling
opening
c::, fig. 2 59.
"Carefully add 0.S quart (0 .5 liter) of the correct
oil
c::, page 275.
"Close the engine oil filler opening cap.
"Close the engine compartment lid.
276
"Restart the ignition after two minutes and read
the current oil level in the Infota inment system
c::, page 275, Checking the engine oil level.
"Add more oil if necessary.
A WARNING
-When adding oil, do not let oil drip onto hot
engine components . This increases the risk
of afire.
- You must seal the cap on the oil filler open­
ing correctly so that oil does not leak out
onto the hot engine and exhaust system
when the engine is running, because this is
a fire hazard.
-Always clean skin thoroughly if it comes into
contact with engine oil.
- Engine oil is poisonous and must be kept
out of reach of children.
- Store the engine oil securely in the original
container.
(D Note
- If the message l!I Oil level is too full.
Please reduce oil level. appears, there is too
much oil in the engine and there is a risk of
catalytic converter and engine damage. Do
not start the engine . Contact an authorized
Audi dealer or authorized Audi Service Fa­
cility to have excess engine oil extracted if
necessary.
- Your Limited New Vehicle Warranty does
not cover damage or malfunctions due to
failure to follow recommended mainte­
nance and use requirements as set forth in
the Audi Owner's Manual and Warranty & Maintenance booklet.
- Use only a high quality engine oil that ex­
pressly complies with the Audi oil quality
standard specified for your vehicle's engine .
Using any other oil can cause serious engine
damage .
- Do not mix any additional lubricants into
the engine oil. Damage caused by such addi-
tives is not covered by the warranty.
.,._

u. co .... N
" N .... 0 0 :c ' @ For the sake of the environment
-Oil should never enter the sewer system or
come into contact with the ground.
- Pay attention to legal requirements when
disposing of empty oi l containers .
Changing the engine oil
We recommend that hove your oil changed by on
authorized Audi dealer or a qualified service sta­
tion .
Before you check anyt hing in the engine compart ­
ment,
alw ays re ad and h eed all W ARNINGS ¢ &
in Working in the engine comportment on
page 272.
The engine oil must be changed according to the
intervals specified in your Warranty
& Mainte­
nance booklet . This is very important because the
lubricating properties of oil diminish gradually
during normal vehicle use.
Under some circumstances the engine oi l should
be changed more frequently. Change oil more of­
ten if you drive mostly short distances, operate
the vehicle in dusty areas or under predominantly
stop-and-go traffic condit ions, or have your vehi­
cle where temperatures remain below freezing
for extended periods .
Detergent additives in the oil will make fresh oil
look dark after the engine has been running for a
short t ime . Th is is normal and is not a reason to
change the oil more often than recommended .
Because of the problem of proper disposal, along
with the special tools and necessary expertise re­
qu ired, we strongly recommend that you have
your oil changed by an authorized
A ud i d ea ler or
a qualified se rvice station .
If you choo se to chang e your o il y ou rse lf, please
note the following important information:
A WARNING
T o reduce the r isk of personal injury if you
must change the engine oil in your ve hicle
yourse lf:
- Wear eye protection .
-
Check ing and F illing
- To reduce the risk of burns from hot engine
oil, let the engine cool down to the touch.
- When removing the oil drain p lug with your
fingers, stay as far away as possible. Always keep your forearm parallel to the ground to
help prevent hot oil from running down your
arm.
- Drain the oil into a container designed for
this purpose, one large enough to hold at least the total amount of oil in your engine.
- Engine oil is poisonous. Keep it well out of
the reach of children .
- Continuous contact with used engine o il is
harmful to your skin. Always protect your
skin by wash ing oil off thoroughly with soap
and wate r.
@ Note
Never mix oil additives with your engine oil.
These add itives can damage your engine and
adversely affect your Audi L imited New Vehi­
cle War ranty .
@ For the sake of the environment
-Before chang ing your o il, first make sure
you know where you can properly d ispose of
the used oil.
- Always dispose of used engine o il properly .
Do not dump it on garden so il, wooded
areas, i nto open streams o r down sewage
dra ins.
- Recycle used eng ine o il by tak ing it to a used
eng ine oi l collection fac ility in yo ur area, or
c ontact a se rvice station.
Cooling system
Coolant
The eng ine cooling system is filled w ith a mixture
of purified water and coolant additive at the fac­
tory. This coolant must not be not changed .
The coo lant level is mon itored through
the . in­
dicator
light¢ page 20. However, we do recom­
mend occasionally checking the coolant level
manually .
.,.
277

u. co .... N
" N .... 0 0 :c ' ~ At the end of the charging process, switch the
charger off and pull the power cab le out of the
socket.
~ Now remove the charg ing device terminal
clamps .
~ Close the cover @on the positive term inal and
re-install the
cover (!).
~ Close the hood c:;, page 2 73 .
A drained battery can freeze at temperatures
around
322F (0QC) . A frozen or thawed out bat­
tery must no longer be used . The battery hous ing
could be cracked by the format ion of ice , which
could cause battery acid to leak out
c:;, ,&. .
Charg ing the b attery
Only use chargers with a ma ximum charg ing
v oltage of 14 .8 V.
The battery connecting cables
do not need to be disconnected . Do not open the
battery when charg ing .
Read all of the manufacturer's instructions for
the charger before charging the battery .
A WARNING
-A h ighly exp losive mixture of gases can form
w hen cha rging batter ies. O nly charge t he
vehicle ba tte ry in well -vent ilated a reas.
- A d rained vehicle battery can freeze at tem­
peratu res a round 32
Q F (0 QC). A froze n or
thawed ve hicle battery m ust not be ch arged
and must not be used anymore. The battery
housing can crack and battery acid can leak
out if ice forms, whic h increases the risk of
an exp losion and chemical burns. Contact an
authorized Audi dealer or authorized Aud i
Service Facility for more information.
- Do not connect or disconnect the charg ing
cable while charg ing because th is increases
the risk of an explosion .
(D Tips
-Only charge the vehicle battery through the
connections in the engine compartment.
-Read all of the manufacturer's instructions
for the charger before charg ing the ve hicle
battery .
Ch eck ing and F illing
Windshield washer
system
F ig . 263 E ngin e compar tmen t: was he r fl ui d reservo ir cap
M N
-N ' "' "' m
The windshield washer fluid reservoir O contains
the cleaning solution for the windshie ld and the
headlight washer system
c:;, fig. 263, c:;, page 274.
The reservoir capacity can be found in
<=> page 334.
To reduce the risk of lime scale depos its on the
spray nozzles, use clean water with low amounts
of calcium. Always add w indow cleaner to the wa­
ter . When the outside temperatures are cold, an
anti -freezing agent should be added to the water
so that it does not freeze .
@ Note
-The concentration of ant i-freez ing agent
must be adjusted to the veh icle operat ing
condit ions in the respective cl imate . A con­
centration that is too high can lead to vehi­
cle damage.
- Never add radiato r anti-freeze or other addi­
t ives to the washer fluid.
- Do not use a glass cleaner that conta ins
paint so lvents, because t his could damage
the paint.
Service interval display
The service interval display detects when your ve­
hicle is due for service.
T he serv ice interval d isplay wo rks in two stages:
-In sp ec tio n o r oil change remind er: after a cer-
tain distance driven , a message appears in the
.,.
2 8 1

Checking and Filling
instrument cluster display each time the ign i­
tion is switched on or off . The rema ining
distance or time is displayed br iefly.
- Inspection or oil change due: if yo ur vehicle
h as reached an inspection o r oi l change interval
o r both intervals at t he same time, the mes­
sage
Inspection due! or Oil change due! or Oil
change and inspection due!
appears br iefly af­
te r switch ing the igni tion on/off .
Checking service intervals
You can check t he rema ining distance o r time un­
til the next oil change o r next inspec tion i n the
Ca r menu. To do this, select: the
IC ARI function
button
> Car systems contro l bu tton > Service &
control > Service intervals .
Resetting the indicator
A n author ized A udi dealer or authorized A udi
Serv ice Facility will reset the serv ice interval d is­
p lay after pe rforming serv ice .
I f yo u have chan ged t he oil you rself, you must re ­
set t he oil change interva l.
To reset the in dic ator, se le ct : th e
ICAR I fu nc tion
but ton
> Car system s control button > Service &
control > Service intervals. T urn t he control knob
downwa rd to
Reset oil change interval an d press
the co ntro l knob.
{QJ Note
- On ly reset the oil ch ange in dicato r if the oil
was c han ge d.
- Fo llow ing the service i nte rvals is cr itical to
maintai ning the service life a nd value o f
your ve hicl e, especia lly t he engine. Even if
the m ileage on the veh icle is low, do not ex­
c e ed th e tim e fo r th e ne xt serv ic e .
282

u. a:, .... N
" N .... 0
0
I Wheels
Wheels and Tires
General information
~check your tires regularly for
damage (punctures, cuts, cracks
and bulges). Remove foreign ob­
jects from the tire tread.
~ If driving over curbs or similar
obstacles, drive slowly and ap ­
proach the curb at an angle.
~Have faulty tires or rims re­
placed immediately.
~Protect your tires from oil,
grease and fuel.
~Mark tires before removing
them so that the same running
direction can be maintained if
they are reinstalled.
~Lay tires flat when storing and
store them in a cool, dry location
with as little exposure to light as possible.
(D Note
-Please note that summer and winter tires are designed for
the conditions that are typical in those seasons. Audi recom­
mends using winter tires dur­
ing the winter months. Low
temperatures significantly de­
crease the elasticity of summ­
er tires, which affects traction
Wheels
and braking ability. If summer
tires are used in very cold
temperatures, cracks can form on the tread bars, resulting in
permanent tire damage that
can cause loud driving noise
and unbalanced tires.
-Burnished, polished or chromed rims must not be
used in winter driving condi­
tions. The surface of the rims does not have sufficient corro­
sion protection for this and
could be permanently dam­
aged by road salt or similar
substances.
Tire designations
Fig. 264 Tire specification codes on the
sidewall of a tire
.,.
283

Wheels
Bead
means the part of the tire that is
made of steel wires, wrapped or
reinforced by ply cords and that is
shaped to fit the rim .
Bead separation
means a breakdown of the bond
between components in the bead .
Cord
means the strands forming the
plies in the tire .
Cold tire inflation pressure
means the tire pressure recom­
mended by the vehicle manufac­
turer for
a tire of a designated
size that has not been driven for more than a couple of miles (kilo­
meters) at low speeds in the
three hour period before the tire pressure is measured or adjusted .
Curb weight
means the weight of a motor ve­
hicle with standa rd equipment in ­
cluding the maximum ca pacity of
fuel, oil, and coolant, air condi ­
tioning and addit ional weigh t of
optional equipment.
E x tra load tire
means a tire designed to operate
at higher loads and at higher
in -
28 6
flation pressures than t he corre­
spond ing standard tire. Extra load
tires may be identified as "X L",
"xl" , "EXTRA LOAD" , or "RF" on
the sidewall.
Gross Axle Weight Rating ("GAWR")
means the load-car rying capacity
of a single axle system , measu red
at the ti re-ground interfaces .
Gross Vehicle Weight Rating
("GVWR")
means the maximum total loaded
weight of the vehicle .
Groove
means the space between two ad­
jacent tread ribs .
Load rating (code)
means the maximum load tha t a
tire is rated to carry for a given i n­
flation pressure. You may no t find
this informat ion on all ti res be­
cause it is not required by law .
Maximum load rating
means the load rating for a tire at
the maximum permissible infla­
tion pressure for that tire .
Maximum loaded vehicle
weight
means t he sum of: