2018 AUDI A4 window

Warm and cold
Warm and cold
Climate control system
Description
The climate control system warms, cools and re­ moves humidity from the air in the vehicle interi­
or. It is the most effective when the windows and
sunroof * are closed. If there is a bui ld-up of heat
inside the vehicle, ventilation can he lp to speed
up the cooling process.
I n all heating mode f unctions except for
defrost,
the blower only switches to a higher speed once
the engine coolant has reached a sufficient tem­
perature .
Pollutant filt er
The po llutant filter removes poll utants such as
dust and pollen from the a ir .
Ke y recognit ion
The climate control settings are automatically
stored and assigned to the remote contro l key
that is in use .
76
® For the sake of the environment
-If you would like to reduce fuel consump­
t ion, sw itch the air conditioning
off. This
will also reduce emissions.
- In veh icles with a diesel engine, you can
switch the auxiliary heater
off in the Info­
tainment system.
(D Tips
- To prevent interference with the heating
and cooling output and to prevent the win­
dows from fogging over, the air intake in
front of the windshie ld must be free of ice,
snow or leaves.
- Condensation from the cooling system can
dr ip and form a pudd le of water under the
vehicle . This is norma l and does not mean
there is a leak.
- The energy management system may tem­ porarily switch
off certain functions, such as
the seat heating* o r rear window defogger.
T hese systems are ava ilable again as soon
as the ene rgy supply has been restored.

Warm and cold
system operates most efficiently in eco cooling
mode.
A/C MAX cooling mode*
You can switch the maximum cool ing mode on or
off using the rocker switch@. Th e air is not
coo led and humidity is not removed when cooling
mode is switched off. This can cause fog on the
windows. Cooling mode switches off automati­
cally when the outside temperature is below
zero. When the cooling mode is switched on, the
vehicle interior is cooled as quickly as possible
and dehumidified .
c:E) Recirculation mode
In recirculation mode, the air inside the vehicle is
circu lated and filtered. This prevents the unfil­
tered air outside the vehicle from entering the
vehicle interior. Switching recirculation mode on
when dr iv ing through a tunnel or when s itting in
traffic is recommended
Q &, .
Using the button, recirculation mode is~ using
the button. You can also switch the recirculation
mode off by pressing the knob (D or the ~ but­
ton.
AUTO
Automatic mode
Automatic mode maintains a constant tempera­
ture inside the vehicle. Air temperature, airflow
and air distribution are controlled automatically .
You can switch automatic mode on or off by
pressing the
knob@.
Temperature
You can adjust the temperature between 60°F
( + 16°()
and 84°F ( +28°() by turn ing the knob
(D . Outs ide of this range, LO or HI will appear in
the climate control system display . In both set­
tings, the climate control runs constantly at the
maximum cooling or heating level. The tempera­
ture is not regulated.
The temperature can be adjusted in the rear us­
ing the rear contro ls
Q fig. 91.
86'~ Blower
You can adjust the vo lume of air generated by the
blower to your preference using the rocker switch
@ . The blower should always run at a low setting
78
to prevent the windows from fogging and to en ­
sure a continuous exchange of air inside the vehi­
cle. To have the blower regulated automatically,
press one of the knobs
(D .
Air distribution
You can use the rocker sw itches @to adjust the
vents where the air will flow out of. Press the
rocker switches @repeatedly unti l the desired
air distribution setting is displayed in the climate
control system controls. To have the air distribu­
tion regulated automatically, press one of the
knobs
(D .
""lll"' OPEN/CLOSE the wide vent
You can open and close the wide vent in the cock­
pit using the rocker switch ®·
JI~ Seat heating and ventilation*
If you press the button J ,J, the seat heating/
ventilat ion is switched on at the highest leve l (3) .
The LEDs indicate the temperature level. To re­
duce the temperature, press the button again. To
switch the seat heating/ventilation off, press the
button repeatedly until the LED turns
off.
3% Defrosting
The windshield and side windows are defrosted
or cleared of condensation as quick ly as possible .
The maximum amount of air flows mainly from
the vents below the windsh ield. Recirculation
mode switches off. The temperature should be
set at
+72°F (+22°() or higher . The temperature
i s controlled automat ically .
Defrost is switched on and off
3% using the but­
ton. You can switch the function off by pressing a knob
(D .
Applies to vehicles with windshield defogger: the
windshield defogger switches on automatically
when outside temperatures are low. If you would like to sw itch the windshield defroster on man­
ually, press the
3%. The LED in the button blinks.
ClWREAR Rear window defogger
Press the button [email protected] switch the rear window de­
fogger on. It on ly operates when the engine is
running. It switches off automatically after
10 to .,,.

a co .... N ,....
N .... 0 0
3 co
20 minutes, depending on the outside
temperature.
To keep the rear window defogger on contin uous­
l y, press and hold the
QWREAR button longer
than
3 seconds. This is stored unti l the ignition is
switched off .
SYNC Synchronization
Use the rocker switc h® to sele ct the funct ion.
When synch ronization is switched on, the set­
tings for the driver's side are applied to the front
passenger's side and the rear (except for seat
heating/venti lation*) . When the settings on the
front passenger's side or in the rear are changed,
the synchron iz at ion is automatically sw itched off
and
3 -z one appears in the display .
SET REAR function
Use t he rocker switch ® to select the function .
When the function is switched on, you can adjust
all settings for the rear us ing the climate control
system controls in the cockpit. The rear climate
control system controls cannot be operated at
the same time . This function switches off auto­
mat ically after a certain period of time or after
leaving the menu.
Vent s
You can open or close the center and rear vents in
the cockpit and the vents in the rear center con­
sole us ing the r idged thumbwheels . The levers
adjust the d irection of the airflow from the vents.
The wide vent is opened and closed using the
r ocker switch
® ·
Residu al heat
You can activate the residual heat funct ion when
the ignition is switched off by pressing the knob
(D . The res idual heat from the coolant is used to
h eat the vehicle inte rior. The residual heat func­
tion swi tches off automatically afte r abou t 15
minu tes .
A WARNING
- You should not use the recirculation mode for an exten ded period of time, because no
fresh a ir is drawn in and the w indows can
Warm and c old
fog when cooling mode is switched off. This
increases the r isk of an accident.
- Individuals with reduced sensitivity to pain
or temperature could develop burns when
using the seat heat ing* function. To reduce
the risk of injury, these individua ls should
not use seat heating*.
(D Note
To avoid damaging the seat heat ing* ele­
ments, do not knee l on the seats or place
heavy pressure on one area of the seat.
Setup
The climate control system basic settings ore ac­
cessed in the Infotainment system .
.,. Select in the Infotainment system : I MENU! but­
ton
> Vehicle > l eft control button > Ai r co ndi ­
tioning
Auto recircu lation
When switched on, a utomat ic rec irculat ion con­
trols the recircu lation mode automatically . You
must press the
®MAX button if fog forms on
the windows.
Automatic auxiliary heater*
T he aux iliary hea ter he lps to wa rm the vehicle in ­
terior more q uickly.
Steering wheel heating
Applies to: vehicles with steering wheel heating
The steering wheel rim con be heated.
.,. Press the bu tton on the m ultif unct ion steeri ng
wheel to switch the steering whee l heating on
and
off~ r=:> poge 15, fig . 11 . The message
Steering wheel heating : on /Steering wheel
heating: off
appears in the instrument cluster
disp lay.
The temperature is maintained at a constant lev­ el when steering wheel heating is switched on .
T he s teer ing whee l heating se tt ings a re stored
automat ica lly and assigned to the remo te control
key that is in use.
79

a co .... N ,....
N .... 0 0
3 co
engaged, for example when you notice that the next traffic light is red . This produces an engine
braking effect, which helps to protect the brakes
and tires and reduces the emissions and fuel con ­
sumpt ion to zero (fuel shut-off dur ing decelera­
tion) .
Shift efficiently
Upshifting earlier is an effective way to save fuel.
Staying in a gear too long uses fuel unnecessari­
ly.
Applies to: vehicles with manual transmission
Shift as soon as possible from first to second
gear. S hifting to the next highest gear at approxi­
mately 2,000 RPMs if poss ible is recommended.
Applies to: vehicles with automatic transmissions
Press down on the acce le rator peda l slowly and
avoid "kick -down".
Avoid full acceleration
You should rarely travel at the maximum vehicle
speed. High speeds cause a disproportionately
high increase in fuel consumption, emissions and
traffic noise. Driving more slowly saves fuel.
Reduce idling time
The Start/Stop system* he lps to reduce the idling
time automatically. In vehicles without the Start/
Stop system*, it is efficient to switch the engine
off when stopped at railroad cross ings and long
r ed lights. Stopping the engine for 30-40 sec­
onds already saves more fuel than the amount of
extra fuel needed to restart the eng ine.
It takes a very long time in idle to warm the en­
g ine up to operating temperature. Wear and
emissions are especially h igh in the wa rm-up
phase . Therefore, you should begi n driving im­
mediately a fter starting the engine . Avoid high
RPMs while do ing this .
Have maintenance performed regularly
By having maintenance performed regu larly on
your veh icle, yo u ca n he lp to reduce f uel con­
sumption before yo u even start to drive. The
maintenance condition of your vehicle not only
affects traffic safety and long-term value but a l-
Driving
so impacts fuel consumption . A poorly main ­
tained engine can lead to fuel consumption that is 10% higher than norma l.
Avoid short trips
The eng ine and exhaust cleaning system must
reach their optimal operat ing temperatu re to ef­
f ectively reduce consumption and emissions.
A cold engine uses a disproportionately high
amount of fue l. The engine reaches operating
temperat ure and consumption normalizes on ly
after approximate ly 2.5 miles (4 km).
Check the tire pressure
To save fuel, make sure the tires are always in­
flated to the correct press ure
~ page 344. The
fuel consumption can increase by 5% if the pres­
s u re is only 0.5 bar too low. Due to the increased
rolling resistance, low tire pressures wi ll also
l ead to greater tire wear and will affect driving
behavior.
Do not drive on winter tires year-round, as this
will consume up to 10% more fuel.
Eliminate unnecessary weight
S in ce eve ry po und of ext ra weight increases f uel
consumption , a quick inspection of the luggage
compartment may be worth it to avoid unneces ­
sary weight .
When not be ing used , a roof rack should be re­
moved to decrease the wind resistance of the ve­
hicle. This will save you approximately 12% fuel
at speeds from 62 -75 mph (100 - 120 km/h) .
Save energy
The eng ine drives the generator, which generates
electric ity; the fuel consumpt io n also incr eases
with the demand for electr icity. The refore, switch
electrical eq uipment off when you no longer
need it . Examples of equipment that uses a lo t of
energy are air blowers at a high setting, the rear
window defogger and seat heating* .
@ Note
Do not leave engine idling unattended after
starting. If warning lights shou ld come on to
indicate improper operation, they would go
81

Driving
St ee ring lock1
)
The stee ring locks when you t urn the engine off
using the
! S T A RT ENGINE ST OP I button and
open the driver 's door. The locked steering helps
prevent v ehicle theft .
Emergency off function*
If it is abso lutely necessary, the engine can also
be turned off while dr iv ing at speeds star ting at
4 mph (7 km/h). To switch the eng ine off, press
the
! S TAR T ENGINE ST OP I button tw ice in a row
briefly or press and hold for longer than two sec­
onds.
A WARNING
- Never turn off the engine before the veh icle
has come to a comp lete stop . The full func­
t ion of the brake booster and the power
stee ring is not guaranteed. Yo u must use
more force to turn or b rake . Because you
cannot s teer an d brake as you usu ally
would, t his co uld lead to accidents and ser i­
ous in juries.
- Alw ays t ake the key wi th you w henever you
leave you r vehicle . Othe rw ise, the engi ne
cou ld be started o r electrical equipment
s uch as the power windows cou ld be operat­
ed . This can lead to se rious injury.
- For safety reasons, always park the vehicle
with the se lector lever in the P position
(a u­
tomat ic transmission) or with 1st gear en­
gaged (manual transmission). Otherwise
the vehicle could roll away u nintent ionally .
(D Note
If the eng ine has been under heavy load for
an extended per iod of t ime, heat builds up in
the engine compartment after the engine is
sw itched off and there is a risk of damaging
the engi ne . For this reason, let the engi ne run
for at idle for approximately two minutes
be­
fore shutting it off.
l) Th is fun ction is not avai la bl e in al l co un tries.
84
(D Tips
Fo r u p to 10 minutes after stopping the en­
g ine, the radiator fan may turn on again auto­
matically or it may continue to r un (even if
the ig nition is switched off) for the following
r easons:
- The coolant temperature is increas ing due
to trapped heat.
- If the eng ine is wa rm and the eng ine com­
partment a lso heats up from strong sun­
light .
- Applies to: vehicles with diesel particulate
filter: The emissions control system is heat­
ed through the regeneration process, even if
the engine has not reached its operat ing
tempe rature yet.
Messages
Engin e running . Warning! Turn off ignition be ­
fore leavin g vehicle
This message appears and a warning tone sounds
i f you open the drive r's door w hen the eng ine is
r un ning .
Applies to: vehicles with manual transmission
Please pres s clutch pedal
This message appears if you do not press the
clutch pedal to start the eng ine. The engine can
o nly be started w hen the clutch pedal is pressed.
Applies to: vehicles with automatic transmissions
Plea se pres s brake pedal
This message appears if you do not press the
bra ke peda l when sta rting t he eng ine .
Ill Remote control key : key not recognized. Is
the key still in the vehicle ?
This indicator light turns on and this message ap­
pears if the ignition key was removed from the
vehicle when the engine was running . If the igni­
tion key is no longer in the vehicle, you cannot
switch on the ignition or start the engine once

a co .... N ..... N .... 0 0
3 co
~ Applies to: automatic transmission: Select the
P selector lever position .
~ Turn the eng ine off ¢,&. .
~ Applies to: manual transmission: Engage 1st
gear.
~ Turn the steering wheel when parking on in ­
clines so that the wheels will roll into the curb
if the veh icle starts moving .
A WARNING
-Never accelerate or release the clutch pedal
carelessly when a gear or a selector lever
posit ion (automatic transmission) is engag­
ed whi le the vehicle is stationary and the en­
gine is running. Otherwise, the vehicle will
start to move immediately and this cou ld re­
sult in an accident.
- Emergency braking should only be used in
an emergency, when the normal brake peda l
has failed or the brake pedal is obstructed.
During emergency braking, your veh icle will
brake sim ilar to heavy brak ing . ESC and the
associated components (ABS, ASR, EDL)
cannot overcome the laws of physics,
Around curves and when road or weather
conditions are bad, a full brake application
can cause the vehicle to skid or the rear end
to swerve, which increases the risk of an ac­
c ident.
- If the power supply fails, you cannot set the
park ing brake if it is released . If th is is the
case, stop the veh icle on leve l ground and
secure it by engaging 1st gear (manual
transmiss ion) or select ing the P selector lev ­
er position (automatic transm iss ion). See an
authorized Aud i dealer or autho rized Aud i
Service Facility for assistance .
- Always take the vehicle key with you when
leaving your vehicle, even if for a short pe ri­
od of time. This applies particu larly when
children remain in the vehicle. Otherwise,
children could start the engine, release the
parking brake or operate electrical equip­
ment such as powe r windows, which in­
creases the risk of an acc ident.
- No one, especially children, shou ld remain
in the vehicle when it is locked. Locked
doors make it more difficult for emergency
D riving
workers to get into the vehicle, which puts
lives at risk.
(D Tips
Ap plies to : vehicles with auto matic transmissions
When stopp ing at a traff ic signa l or stopp ing
i n city traffic, you can set the park ing brake
manually . The vehicle does not have to be
held with the brake pedal. The park ing brake
eliminates the tendency to creep when a se­
l ector lever position is engaged. As soon as
you press the a ccelerator peda l, the parking
brake releases automatically and your vehicle
starts to move r=;,
page 89.
(j) Tips
-Occasional noises when the pa rking brake is
set and released are normal and are no t a
cause for concern.
- The parking brake goes through a self-test
cycle at regular intervals when the vehicle is
stopped. Any noises assoc iated with this are
normal.
- If there is a power failure, the parking brake
wi ll not set if it is released, and it will not
re lease if it is
set ¢.&. . See an a uthorized
Audi dealer or authorized Audi Service Fa­ cility for assistance.
Starting to drive
Various convenience and safety funct ions may be
available when the vehicle begins driving, de­
pending on vehicle equipment .
Starting on hills with the p arking brake set
Requirement: the driver's door must be closed .
~ To start driving comfortably when on a hill , set
the parking brake and begin driving as usual.
The braking force of the parking brake does not
release a utomatically until the wheels build up
enough driving force.
Starting on hills with hill hold assist
Hi ll ho ld assist makes it easier to start on hills.
Requirement: the driver's door must be closed
and the engine must be running.
89

Driving
"'T o activate hill hold assist, press and hold the
brake peda l for several seconds. The vehicle
must be in an uph ill direction of travel.
Afte r releasing the bra ke pedal, the brak ing pow­
er is ma intained for a brie f
moment¢ A to pre­
vent the vehicle from rolling back when starting .
During this time, you can eas ily beg in to move
your veh icle.
A WARNING
- If you do not begin dr iving immediately or
the engine stalls after releas ing t he brake
peda l, yo ur vehicle may begi n to roll back­
ward . Press t he b rake pedal o r set the park ­
i ng bra ke immed iate ly.
- The intelligent techno logy of hill hold assist
c annot overcome the lim itations imposed by
n atu ral physical laws. The incre ased comfo rt
offered by h ill hold assist sho uld not cause
yo u to take safety risks .
- Hill ho ld assis t can not hold the veh icle in
place on all h ills ( for example, i f the gro und
is slippery or icy) .
- T o reduce the risk of an ac cident, always
make sure the vehicle is si tuated safely
whi le stat ionary.
Driving offroad
General information
A ppl ies to: a ll r oad
The electro nic stabilization co ntrol (ESC) func­
tions were e nhanced for dr iv ing offroad. Offroad
mode c an be ac tivated whe n driving in situat ions
where slipp age or a different ia l loc k func tion is
necessary ¢ page 147. The h ill descent ass ist is
a lso available, which automatica lly brakes the
ve­
h icle and mainta ins a constant speed as a result
¢ page 148. In add ition, your Audi prov ides con­
tinuous all wheel drive.
However , you r Audi is not an offroad vehicle.
Only drive in terrain that is su itable for the vehi ·
cle and your driving abilit y. Never take an y un·
neces sary risks!
90
Afte r driving offroad
- After driving off road , remove b ranches and
other debris from the rad iator grille, under ­
body, and wheels . Look especially fo r foreign
objects (such as stones) that may be st uck in
the t ire tread.
- Clean the vehicle body and underbody and
in­
spect the vehicle for possible damage.
- Clean the windows, headlights, tail lights and
the license p late if they are dirty.
- Per form a brake test (especia lly after d riving
throug h water) .
A WARNING
-Be especially aware and attentive when d riv ­
ing under diff icu lt cond itions. Vehicle dam­
age and in juries may occur when driving at
excess ively high speeds or with incorrect
driving maneuvers.
- Always ad just yo ur speed and driving sty le
to the roads, terrain, traffic and weat her
conditions . Drive especially slowly if there is
low visibility when off road.
- Please note that t he wheels can sp in mo re
and the vehicle can swerve when in offroad
mode, espe cially when the road is slippery
or h as loose s urfa ce mate rial.
- D riving stability is reduce d when in offroad
mode.
@ For the sake of the environment
Avo id harm ing the env ironmen t and show
conside ration fo r nat ure.
(D Tips
Only drive where it is permitted and always
stay on the prov ided roads and paths .
Driver messages
Applies to : allroad
There is only one right way to drive in difficul t
conditions: slowly and with caution!
Observe the following when driving on unpaved
r oads :
1111>

Assistance systems
Switching off completely
.. Press the leve r into posit ion @ (clicked into
place), or
.. Switch the ignition off.
The speed yo u sto red w ill be mainta ined if the
cru ise control has been switched off tempora rily.
To resume the stored speed, release the brake or
clutch pedal and pu ll the leve r into position
(D.
Sw itching the ign ition off will erase the stored
speed.
A WARNING
You shou ld only resume the stored speed if it
is not too high for existing traffic cond itions.
Otherwise you can increase the r isk of an acci­
dent.
Camera-based traffic
sign recognition
Description
Applies to: veh icles with camera-based traffic sign recogni·
tion
Fig. 104 Inst rumen t cluster: traffic sign recognition
Fig. 105 Windsh ield: camera window fo r tra ffic sign recog ­
nit ion
104
Traffic sign recognition assists you when driving
by displaying detected speed limits or signs pro­
hibiting passing in the instrument cluster display
¢ fig. 104. Within the limits of the system, the
legal speed limits in schoo l zones are detected
and displayed .
General information
Traffic sign recognition can detect standard
speed limit signs that are within the camera's vis­
u al field. With assistance from navigation data,
detected speed limits are evaluated and shown in
the d isplay. The traffic s ign for the current de­
tected speed lim it will blink in the display if you
exceed the warning threshold set in the Infota in­
ment system
¢ page 1 OS.
Th e traffic sign recognition is subject to certa in
system limitat ions and may be unava ilable or on­
l y part ially ava ilab le in the follow ing s ituations:
- when visibility is poor, such as in snow, rain,
fog or heavy spray
- when there is glare, for example from oncom­
ing traffic or the sun
- at high speeds
- if the camera's visual
field¢ fig. 105 is covered,
for examp le by dirt or stickers. For information
on cleaning,
see¢ page 354
- if the traffic signs are completely or partially
covered, for examp le by trees, snow, dirt or
other vehicles
- if speed traffic signs do not conform to the
standards
- if traffic signs are damaged or bent
- if traffic signs are displayed on sign holders
with electronic signs
- if the traffic signs o r the config uration of the
road have changed (navigation data is no lon­
ger up-to-date)
_& WARNING
Pay attention to traffic and the area around
your vehicle when traff ic sign recogn ition is
turned on . The traffic s igns installed on the
road always take precedence over the display .
The drive r is always responsible for assessing
the traffic situation.
-